• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.5
• /
• pp.70-75
• /
• 2007

A dual-frequency dual-polarization (DFDP) antenna with high isolation between two ports by embedding $2{\times}1$ mushroom-like electromagnetic bandgap (EBG) cells is proposed. The equivalent circuit of a suspended microstrip line over $2{\times}1$ EBG cells is introduced. The numerical analysis from the equivalent circuit and measured results show that the microstrip line with embedded EBG cells has a distinctive and sharp rejection band and provides near 0 dB insertion loss outside the rejection band. By embedding the EBG cells under feedlines of a conventional DFDP antenna, the isolation between two ports of the antenna is enhanced more than 20 dB, as compared to that of a conventional DFDP antenna. The proposed DFDP antenna is fabricated and measured. The simulated and measured results show a good agreement. The measured polarization purity and gain of the antenna are 25 dB and 5.77 dBi at lower band, and 35 dB and 7.13 dBi at higher band, respectively.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.25-27
• /
• 2010

This paper presents a gain and phase mismatch calibration technique for an image-reject RF receiver. The gain mismatch is calibrated by directly measuring the output signal amplitudes of two signal paths. The phase mismatch is calibrated by measuring the output amplitude of the final IF output at the image band. The calibration of the gain and phase mismatch is performed at power-up, and the normal operation of the RF receiver does not interfere with the mismatch calibration circuit. To verify the proposed technique, a 2.4-GHz Weaver image-reject receiver with the gain and phase mismatch calibration circuit is implemented in a 0.18-${\mu}m$ CMOS technology. The overall receiver achieves a voltage gain of 45 dB and a noise figure of 4.8 dB. The image rejection ratio(IRR) is improved from 31 dB to 59.76 dB even with 1 dB and $5^{\circ}$ mismatch in gain and phase, respectively.

• Publications of The Korean Astronomical Society
• /
• v.13 no.1 s.14
• /
• pp.39-54
• /
• 1998

We have developed solar observational system in the department of Astronomy & Space Sciences of KyungHee University, in order to monitor solar activities and construct solar database for space weather forecasting at maximum of 23rd solar cycle, as well as an solar education and exercise for undergraduate students. Our solar observational system consists of the full disk monitoring system and the regional observation system for H a fine structure. Full disk monitoring system is made of an energy rejection filter, 16cm refractor, video CCD camera and monitor. Monitored data are recorded to VHS video tape and analog output of video CCD can be captured as digital images by the computer with video graphic card. Another system for regional observation of the sun is made of energy rejection filter, 21cm Schmidt-Cassegrain reflector, H a filter with 1.6A pass band width and $375\times242$ CCD camera. We can observe H a fine structure in active regions of solar disk and solar limb, by using this system. We have carried out intense solar observations for a test of our system. It is found that Quality of our H a image is as good as that of solar images provided by Space Environmental Center. In this paper, we introduce the basic characteristics of the KyungHee Solar Observation System and result of our solar observations. We hope that our data should be used for space weather forecasting with domestic data of RRL(Radio Research Laboratory) and SOFT(SOlar Flare Telescope).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.5
• /
• pp.463-470
• /
• 2015

In this paper, a new dual-band bandpass filter(BPF) that has resonators and feed lines with Stepped-Impedance Resonator(SIR) structures is proposed. Feed lines with SIR structure provide maximum magnetic field points which occur at the same locations of the input and output feed lines, so the insertion loss of BPF was reduced. Applying the SIR structure to the BPF for the first passband improves rejection characteristics between the first passband and the second passband. It reduces the coupling between the BPF for the first passband and the BPF for the second passband, so it makes the dual-band BPF more compact. The proposed design method provides independent changes of both the center frequency and the bandwidth for each resonator, and also improves filtering characteristics. The validity of the proposed design method is confirmed by comparisons between the designed parameters and the measured results satisfying WLAN specifications.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.649-652
• /
• 2007

In the world each bureau tries an introduction of Mobile WiMAX frequency in the various band. Particularly, 2.5 GHz band is likely to be used as the future mobile telecommunication using as the IMT-2000 additional band which determined in WRC, and it comes into the spotlight as the band of the global radio broadband service including the Mobile WiMAX. Thus, the activity for including the Mobile WiMAX to the IMT-2000 technical standard is unfolded for the WiBro market development in the ITU-R WP8F conference, and the adoption or rejection will be finally determined in the ITU-R RA-07. Therefore, this paper tried to look for the plan for reaction according to the IMT-2000 standard acceptance of WiBro technology and the foreign usage plan of 2.5 GHZ band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.6
• /
• pp.552-559
• /
• 2002

The EM(Engineering Model) LO(Local Oscillator) is designed for Ka-band satellite transponder. The VCO(Voltage Controlled Oscillator) is implemented using a high impedance inverter coupled with dielectric resonator to improve the phase noise performance out of the loop bandwidth. The phase of VCO is locked to that of a stable OCXO(Oven Controlled Crystal Oscillator) by using a SPD(Sampling Phase detector) to improve phase noise performance in the loop bandwidth. This LO exhibits the harmonic rejection characteristics above 43.83 dBc and requires 15 V and 160 mA. The phase noise characteristics are performed as -102.5 dBc/Hz at 10 KHz offset frequency and -104.0 dBc/Hz at 100 KHz offset frequency, respectively, with the output power of 13.50 dBm$\pm$0.33 dB over the temperature range of -20~+7$0^{\circ}C$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.105
• /
• pp.89-94
• /
• 2006

A compact microstrip band-selective filter for ultra-wideband(UWB) radio system is proposed. The filter combines the traditional short-circuited stub highpass filter and coupled resonator band-stop filter on both sides of the mitered 50-ohm microstrip line. To realize the pseudo-highpass filtering characteristic over UWB frequency band(3.1 GHz to 10.6 GHz), a distributed highpass filter scheme is adopted. Three coupled resonators are utilized to obtain the band stop function at the desired frequency band. By meandering the coupled resonators, there is $29\;\%$ size reduction in footprint compared to the traditional band-stop filter using L-shaped resonators. The measured results show that the filter has a wide passband of $146.7\;\%$(2.1 GHz to 10.15 GHz) with low insertion loss and the stop band of $10.04\;\%$(5.2 GHz to 5.75 GHz) for 3-dB bandwidth. The measured group delay is less than 0.7 ns within the passband except the rejection band.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.1
• /
• pp.10-15
• /
• 1999

We have studied a method to design and fabricate the Intermediate Frequency(IF) band pass filter with low shape factor which is used for CDMA base station on the 35°Y-cut X-propagation Quartz substrate. In order to fabricate a device of the low shape factor for the IF SAW filter on this substrate, we employed apodization weighted type interdigital transducer(IDT) as an input and withdrawal weighted type IDT as an output by using impulse modelling method. Also, using the Kaiser-Bessel window function, we have adopted 2200pairs and 1000pairs of input and oueut IDT respectively to minimize the effect of ripple. Furthermore, the width and the space of IDT finger are 3.6 ㎛ and 3.5 ㎛ respectively. Thus, we can have optimal results when the IDT thickness is 6000Å in consideration of the ratio of SAW's wavelength while it's aperture is 2mm for impedance matching. The fabricated SAW filter for CDMA had the property of almost 115.2MHz of a center frequency, less then 1.27MHz of bandwidth, less than 1.3 of shape factor, - l5dB of out band attenuation insertion loss and -45dB of rejection band.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.4
• /
• pp.38-42
• /
• 2010

In this paper, a design method of the compact narrow band filter on the microstrip board is proposed using slot-type split spiral resonators. The design technique of this filter is based on cascading filter stages consisting of the combination of slot-type split spiral resonators, capacitive gaps between patches, and inductive grounded stubs with the meander configuration. By these means, it was possible to get the nearly symmetric frequency responses, adjustable bandwidths, compact sizes. And also excellent characteristic of the out-of-band rejection is achieved in contrast to the conventional filter design technique. The measured insertion loss shows good results about -3.47dB at the center frequency($f_0$=1GHz) and passband return loss is less than -12.62dB. The 3dB fractional bandwidth(FBW) is approximately 7.3%. The results of the frequency response measured on the fabricated band pass filter substrate show satisfactory agreement with the simulated frequency responses by the MWS(Microwave Studio) of CST in the region of interest.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.3
• /
• pp.1-6
• /
• 2008

A dual band I/Q modulator which converts baseband input signals to 2.4GHz or 5GHz RF output has been proposed. The dual band I/Q modulator for 2.4GHz and 5GHz wireless LAN applications consists of $90^{\circ}$ phase shifter and wideband mixer. The I/Q modulator showed 15dB conversion loss at 2.4GHz and 16dB conversion loss at 5GHz. The sideband suppression is about 15dBc at 2.4GHz and 16dBc at 5GHz. Measured data shows 8.5% EVM at 2.4GHz, and 10% EVM at 5GHz for QPSK with symbol rate of 11Mbps. A carrier rejection is about 40dBc at 2.4GHz/5GHz band, and the I/Q modulator satisfied the output wireless LAN spectrum mask with baseband input signal.