• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 추계학술대회 논문집
• /
• pp.106-110
• /
• 2001

The ball-end milling process is widely used in the die/mold industries, and it is very suitable for the machining of free-form surfaces. However, this process is inherently inefficient process to compared with the end-milling or face milling process, since it relays upon the machining at the cutter/surface contact point. The machined part is the result of continuous point-to-point machining on the free-form surface. And cusps (or scallops) remain at the machined part along the cutter paths and they give the geometrical roughness of the workpiece. Thus, for the good geometrical roughness of the workpiece, it is required very tightly spaced cutter paths in this ball-endmilling process. However, with the tight cutter paths, the geometrical roughness of the workpiece is not regular on the workpiece since the cusp height is variable in the previously developed ISO-parametric or Cartesian machining methods. This paper suggests a method of tool path generation which makes the geometrical roughness of workpiece be constant through the machined surface. In this method, Ferguson Surface design Model is used and cusp height is derived from the instantaneous curvatures. And, to have constant cusp height, an increment of parameter u or v is estimated along the reference cutter path. In ball-end milling experiments, the cusp pattern was examined, and it was proved that the geometrical roughness could be regular by suggested tool path generation method.

• 대한기계학회논문집
• /
• 제13권3호
• /
• pp.433-442
• /
• 1989

본 연구에서는 볼 엔드 밀 절삭실험을 통하지 않고 일반적인 선삭가공 등에서 쉽게 구할 수 있는 2차원 절삭 데이터를 이용하여 볼 엔드 밀의 기하학적 형상 및 절삭조건이 주어졌을 때 모든 볼 엔드 밀 가공에서의 절삭기구를 해석하고 절삭력 모델을 구하고자 한다. 이를 위하여 볼 엔드 밀의 기하학적 특성 및 절삭 조건 등을 분석하고, 미소절삭날터를 이용한 3차원 절삭해석방법을 적용하여 미소 절삭력을 구하고 이들의 합력으로서 절삭력을 계산한다.

• 반도체디스플레이기술학회지
• /
• 제13권3호
• /
• pp.51-55
• /
• 2014

Ni-CNT(Carbon Nanotubes) composite coating is often used for the surface treatment of mechanical/electronic devices to improve the properties of the Ni coating. For the Ni-CNT coating, the dispersion of CNT fibers is a critical process. In this study, ultrasonic treatment instead of the conventional ball milling was attempted as a dispersion method for the electroless Ni-CNT coating. SEM-EDX analysis was performed and contact angle, sheet resistance, and micro-hardness were measured. Results showed that the ultrasonic treatment was comparable to the ball milling, as a dispersion method, but the difference was negligible. However, combined ball milling and ultrasonic treatment(double treatment) showed much improved micro-hardness value, above 350Hv(close to the value obtained by the Ni-CNT electroplating). In addition, electroless Ni-CNT(double-treated) coatings formed on the thin Ni film deposited by the electroless plating(double coating) showed better mechanical properties. Thus, double treatment and double coating are suggested as an improved electroless Ni-CNT coating method.

• 한국분말재료학회지
• /
• 제12권6호
• /
• pp.387-392
• /
• 2005

The p-type semiconductor $Bi_2Te_3-Sb_2Te_3$ thermoelectric materials were fabricated by melting, milling and sintering process and their thermoelectric properties were characterized. The compound materials were ball-milled with milling time and the powders were sintered by spark plasma sintering process. The ball milled powders had equiaxial shape and approedmately $1\~3{\mu}m$ in size. The figure of meritz of sintered thermoelectric materials decreased with milling time because of lowered electrical resistivity. The thermoelectric properties of $Bi_2Te_3-Sb_2Te_3$ materials have been discussed in terms of electrical property with ball mill process.

• 한국분말재료학회지
• /
• 제18권4호
• /
• pp.378-384
• /
• 2011

In this research, the indium dissolution properties of the waste LCD panel powders were investigated as a function of milling time fabricated by high-energy ball milling (HEBM) process. The particle morphology of waste LCD panel powders changed from sharp and irregular shape of initial cullet to spherical shape with an increase in milling time. The particle size quickly decreased to 15 ${\mu}m$ until the first minute, then decreased gradually about 6 ${\mu}m$ with presence of agglomerated particles after 5 minutes, which increased gradually reaching a uniform size of 13 ${\mu}m$ consist of agglomerated particles after 30 minutes. The glass recovery, after dissolution, was over 99% at initial cullet, which decreased to 90.1 and 78.6% with increasing milling time of 1 and 30 minute respectively, due to a loss in remaining powder of the surface ball and jar, as well as the filter paper. The dissolution amount of indium out of the initial cullet was 208 ppm before milling, turning into 223 ppm for the mechanically milled powder after 1 minute, and nearly 146~125 ppm with further increase in milling time because of the reaction surface decrease of powders due to agglomeration. With this process, maximum dissolving indium amount (223 ppm) could be achieved at a particle size of 15 ${\mu}m$ with 1 minute of milling.

• 한국결정성장학회지
• /
• 제34권4호
• /
• pp.125-130
• /
• 2024

헤마타이트와 순금속 Mg 분말에 대하여 볼밀링법을 이용하여 강자성 분말재료를 제조하였으며, 얻어진 분말시료를 800-1,000℃에서 방전플라즈마 소결법을 이용하여 벌크화를 실시하였다. 헤마타이트와 순금속 Mg의 혼합분말을 볼밀링 처리한 결과, 1시간 이전에 강자성 Fe-MgO 복합분말을 얻을 수 있었다. 얻어진 시료의 자화값 및 보자력은 볼밀링 처리 중 헤마타이트와 순금속 Mg의 고상반응에 의하여 변화하였는데, 포화자화 값은 볼밀링 시간에 따라 증가하여 5시간 후에 93.4 emu/g을 나타내었다. 볼밀링 5시간 시료는 방전플라즈마 소결 시 300℃ 이상에서 급격히 수축이 발생한 후 800℃까지 서서히 수축이 진행됨을 알 수 있었다. XRD 피크의 반가폭을 이용한 hall-plot으로부터 900℃에서 소결된 Fe-MgO 벌크체의 Fe 평균 결정립 크기는 50 nm 이었다. 또한 이 벌크시료의 보자력은 90 Oe로 여전히 높은 값을 보였는데 이것은 강자성 Fe 상의 결정립 성장이 소결과정 중에 억제되었기 때문인 것으로 판단된다.

• Bulletin of the Korean Chemical Society
• /
• 제31권9호
• /
• pp.2695-2697
• /
• 2010

• Carbon letters
• /
• 제26권
• /
• pp.11-17
• /
• 2018

Milled carbon fiber (mCF) was prepared by a ball milling process, and X-ray diffraction (XRD) diffractograms were obtained by a $2{\theta}$ continuous scanning analysis to study mCF crystallinity as a function of milling time. The raw material for the mCF was polyacrylonitrile-based carbon fiber (T700). As the milling time increased, the mean particle size of the mCF consistently decreased, reaching $1.826{\mu}m$ at a milling time of 18 h. The XRD analysis showed that, as the milling time increased, the fraction of the crystalline carbon decreased, while the fraction of the amorphous carbon increased. The (002) peak became asymmetric before and after milling as the left side of the peak showed an increasingly gentle slope. For analysis, the asymmetric (002) peak was deconvoluted into two peaks, less-developed crystalline carbon (LDCC) and more-developed crystalline carbon. In both peaks, Lc decreased and $d_{002}$ increased, but no significant change was observed after 6 h of milling time. In addition, the fraction of LDCC increased. As the milling continued, the mCF became more amorphous, possibly due to damage to the crystal lattices by the milling.

• 한국분말재료학회지
• /
• 제15권4호
• /
• pp.302-307
• /
• 2008

$Gd_2O_3$-doped $CeO_2$(GDC) solid solutions have been considered as a promising materials for electrolytes in intermediate-temperature solid oxide fuel cells. In this study, the nano-sized GDC powder with average panicle size of 69nm was prepared by a high energy ball milling process and its sintering behavior was investigated. Heat-treatment at $1200^{\circ}C$ of nano-sized GDC powder mixture led to GDC solid-solution. The enhanced densification over 96% of relative density was obtained after sintering at $1300^{\circ}C$ for 2h. It was found that the sinterability of GDC powder could be significantly improved by the introduction of a high energy ball milling process.

• 한국분말재료학회지
• /
• 제29권5호
• /
• pp.376-381
• /
• 2022

Tungsten disulfide (WS₂) nanosheets have attracted considerable attention because of their unique optical and electrical properties. Several methods for fabrication of WS₂ nanosheets have been developed. However, methods for mass production of high-quality WS₂ nanosheets remain challenging. In this study, WS₂ nanosheets were fabricated using mechano-chemical ball milling based on the synergetic effects of chemical intercalation and mechanical exfoliation. The ball-milling time was set as a variable for the optimized fabricating process of WS₂ nanosheets. Under the optimized conditions, the WS₂ nanosheets had lateral sizes of 500-600 nm with either a monolayer or bilayer. They also exhibited high crystallinity in the 2H semiconducting phase. Thus, the proposed method can be applied to the exfoliation of other transition metal dichalcogenides using suitable chemical intercalants. It can also be used with high-performance WS₂-based photodiodes and transistors used in practical semiconductor applications.