• 제목/요약/키워드: Balancing Design

검색결과 421건 처리시간 0.032초

평행식 진동탄환 암거 천공기의 연구 (IV)(V)-실기 설계 제작 및 보장실험-Development of Balanced-Type Oscillating Mole Drainer(IV)(V)

  • 김용환;이승규;서상용
    • Journal of Biosystems Engineering
    • /
    • 제2권1호
    • /
    • pp.7-24
    • /
    • 1977
  • This paper is the forth and fifth one of the study on balanced type oscillating mole drainer. In the light of the results from previous reports about the model tests, some design criteria were established and a prototype machine was set up for experimental purpose. Motion characteristics and functionof the each parts of the machine were checked and analyzed. After that, performance tests of the prototype machine were carried out in thefield. Obtained results are summarized as follows ; 1. Ten centimeter of the bullet diameter was determined so as to be able to attach it to the tractors with capacity of 30 PS to 40 PS. 2. To maintain the balance between the moments of the front shank and rear shank, the oscillating amplitude of the rear bullet was determined to be larger than that of the front bullet. At the same time , the oscillating direction of the rear bullet was designed with the inclines of ten to thirty degrees. 3. An octagonal dynamo transduced was developed for measuring the compressive force of the upper link is measuring the draft force of the machine. Acceptable linear relationship between forces and strain responses from O.D.T. was obtained. 4. Analysing the balancing mechanism of the acting part of the machine , it was found that the total draft force of the machine was equal to the difference between the sum of the draft force produced from the right and left side bending moments of the lower drawber and the compressive force on the upper link. 5. There are acceptable linear relationship between the strain and twisting moment by driving shaft, and between strain and shank moment. Above results enable us to carry out the field experiment with prototype machine. 6. When the test machine was used in the field, it was possible to reduce the oscillating acceleration by forty percent in average as compared it with the single bullet mole drainer. 7. When the test machine was used under the oscillating condition, the dratt torce was reduced by 27 percent to 59 percent as compared it with the test machine under non-oscillating condition, while the draft force was increased by 7 percent to 20 percent as compared it with the mole drainer having oscillating single bullet. The reasoning behind this fact was considered as the resistance force due to the rear shank and bullet. 8. As the amplitude and frequency of the bullet were increased, the torque was increased accordingly. This tendency could be varied with the various characteristics of the given soils. And the larger frequency and amplitute, the more increasing oscil\ulcornerlating power but decreasing draft brce were needed, and draft force was increased as the velocity was increased.9. When the amplitude of the rear bullet was designed to be larger than that of the front bullet, the minimum value of the moment was lowered and oscillating acceleration was reduced. And when the oscillating direction of the rear bullet was declined back\ulcornerwards, oscillating acceleration was increased along with the increasing angle of decli\ulcornernation. When the test machine was operated in high speed, the difference between maximum moments and minimum ones became narrow. This varying magnitude of moments appeared on the moment oscillogram seems to be correlated to the oscillating acceleration and draft force. 10. From the analysis of variance, it was found that those factors such as frequency, amplitude, and operating velocity significantly affected in the oscillating acceleration, the draft resistance, the torque, the moment, and the total power required. And interaction between frequency and amplitude affected in the oscillating acceleration. 11. Within the given situation of this study, the most preferable operating conditions of the test machine were 7 Hz in oscillating frequency, 0.54 m/sec in operating velocity, and 39.1 mm in oscillating amplitude of front and rear bullets. However, it is necessary to select the proper frequency and magnitude of oscillation depending on the soil properties of the field in which the mole drainer is practiced by use of a bal1nced type oscillating mole drainer. 12. It is recommended that a comparative study of the mole drainers would be performed in the near future using two separate balanced oscillating bullet with the one which is operated by oscillating the movable bullet in a single cylinder or other balanced type which may be single oscillating bullet with spring, damper or balancing weight, and that of thing. To expand the applicability of the balanced type oscillating mole drainer in practical use, it is suggested to develop a new mechanism which perform mole drain with vinyl pipe or filling material such as rice hull.

  • PDF

글로벌 공급사슬에서 경쟁협력 스케줄링을 위한 에이전트 기반 플랫폼 구축 (Development of Agent-based Platform for Coordinated Scheduling in Global Supply Chain)

  • 이정승;최성우
    • 지능정보연구
    • /
    • 제17권4호
    • /
    • pp.213-226
    • /
    • 2011
  • 글로벌 공급사슬 환경에서 글로벌하게 분산 조달, 생산, 유통하게 됨에 따라 전체 공급사슬의 스케줄을 최적화하기 위해서 공급사슬상의 개별 기업 혹은 공장의 스케줄링 최적화뿐만 아니라 각 개별 기업 혹은 공장의 스케줄을 긴밀하게 연계하는 것이 필요하게 되었다. 이는 경쟁과 협력을 동시에 하는 개별 기업 혹은 공장을 개별 에이전트로 보고 각 에이전트간 커뮤니케이션을 통해 개별 에이전트가 관할하는 스케줄러의 스케줄을 조정함으로써 가능해진다. 하지만 전통적인 스케줄링 연구는 개별 스케줄러의 최적화에 집중되어 있고, 에이전트 연구는 스케줄링 도메인에 적용한 예가 제한적이며 이 예도 개별 스케줄러 내의 최적화에 적용하거나 실제 현장 문제가 아닌 실험실 문제 수준에 그치고 있다. 따라서 본 연구에서는 전체 글로벌 공급사슬 스케줄의 최적화를 위해 개별 기업 혹은 공장 스케줄러의 스케줄링을 연계하는 경쟁협력 스케줄링을 위한 에이전트 기반 플랫폼을 구축하였다. 글로벌 공급사슬에서 경쟁협력 스케줄링을 위한 에이전트 기반 플랫폼을 구축하기 위해 첫째, 경쟁협력 스케줄링 분류 체계를 확립하고, 둘째, 경쟁협력 스케줄링을 위한 에이전트를 설계하고, 셋째, 경쟁협력 스케줄링을 위한 지식기반 의사결정 모델을 개발한 후, 넷째 조선산업에 적용 가능한 프로토타입 시스템을 개발했다. 이를 통해 글로벌 공급사슬상의 전체 스케줄의 품질과 에이전트간 커뮤니케이션의 노력에 대한 균형점을 찾을 수 있다. 이를 통해 공급사슬내 개별 기업 혹은 공장의 부분 최적화를 극복할 수 있는 대안을 제시할 것으로 기대한다.

평행식 진동탄환 암거 천공기의 연구(III)-견인력, 토크, 동력 및 모멘크에 관한 모형시험- (A Study on Balanced -type Oseillating Mole-Drainer(III)-Model Test for Draft Force, Torque, Power and Moment)

  • 김용환
    • Journal of Biosystems Engineering
    • /
    • 제1권1호
    • /
    • pp.1-6
    • /
    • 1976
  • This paper is the third one of the study on balanced type oscillating mole-drainer, the first one was presented in No 9. Gyeongsang College Report and the second one in Vol. 17, No.4 of the KSAE. In the first part of this study, the characteristics of traction forces between the nonoscillating earth working equipments and oscillating ones was compared. A model of the balanced type oscillating mole-drainer, which composed of a mechanism that may reduce the machine vibration, was designed following the dimensional analysis and similitude technique. The model test was carried out to clarify the balancing mechanism of the oscillating parts and other parts of the machine. In the light of the results from the model tests, a prototype machine was made for experimental purpose. Results from the field test by a reported in the near future. In the second report, the model tests were carried out under the same soil conditions, i.e, . oscillating frequency, running velocity, and oscillating amplitude, etc. It was clear that use of balanced type oscillating model could substantially reduce the vibration of the whole system of the machine, when compared with the nonoscillating type model. In this paper(the third report), results of investigation on the traction force, power requirement, and moment. etc, is presented. Analysis of variance technique was used for analyzing the effect of the frequency, amplitude, and running velocity on the draft force, torque, power requirements, and moments. The results obtained from the model tests are as follows, 1) By practicing a balanced-type oscillating mole-drainer, it was possible to reduce the traction resistance by 55.1-61. 2 percent of traction resistance, however, was 1.75 - 1.95 times greater than the value of resistance which was induced by use of a mole-drainer with single bullet. The resistance of rear shank against soil was considered as a main causing factor of the above results. 2) As the oscillation frequency was increased, the traction resistance was decreased. Considering on the effect of oscillation the greater the amplitude, and the slower the running velocity was, the greater the reduction ratio of traction resistance was. 3) The ratio of the traction resistance of oscillating mole-drainer to that of non-oscillating one could be represented as a function of dimensionless variable (V/$Af$). The results from the tests were well agreed with the reported results from the experim ents on oscillation plow or hoe. 4) By taking a lower value of (V/$Af$), reducing the traction resistance was possible. This fact meant, however, that the efficiency of mole drain practice would be lower. 5) It was experimentally confirmed under the same condition of soil that the variable (R/$rD1^3$) could be represented as a function of a variable($V^2/gD$) when a non\ulcornerocillating mole-drainer was used. 6) When a oscillating mole-drainer was used, the variable(R/$rD_1^{3}$) could be represented as a function of two variables ($v^2/gD_1$) and (V^2/gD_1$). 7) The torque was not affected by a change of frequency. However, a relation of proportionality existed between torque and amplitude, running velocity, and ratio of bullet diameter. When a balanced type oscillating mole-drainer with two bullets was used, torque was increased by 52.8-78. 4 percent and total power requirement was also increased. 8) Total power requirement was increased linearly in accordance with the increasing frequency, 41.96 percent of total power was used for oscillating action. The magnitude of total power requirement was 1. 8-9. 4 times greater than that of a non-oscillating mechanism. In the view point of power requirement, it was not advisable to increase the frequency, amplitude, running velocity, and ratio of bullet diameter at the same time. 9) Only the positive moment occured in the rear shank. Change of the diameter of a rear bullet, could not affect the balancing against the soil resistance. It was necessary for rear bullet to have a large resistance against soil only when the rear bullet was in backward motion. 10) Within an extent of the experimental base, optimum limits for several design factors were A=0.5cm, $f$=22.5Hz, V=O. 05m/sec, and $\lambda$=1.0 By adapting these values traction resistance was reduced by 40 percent and vibration acceleration wa s reduced by 60 percent. Even though the total , power requirements for operating a balanced type oscillation mechanism was greater ~than that of non-oscillating one, using a oscillating mechanism would be more effective. Because a balanced type oscillating mechanism is used, tractive resistance will be reduced and then the lighter . tractive equipment could be used.

  • PDF

공기조화, 냉동 분야의 최근 연구 동향 - 1998년 1999년 학회지 논문에 대한 종합적 고찰 - (Recent Progress in Air Conditioning and Refrigeration Research - A Review of papers Published in the Korean Journal of Air-Conditioning and Refrigeration Engineering in 1998 and 1999 -)

  • 이재헌;김광우;김병주;이재효;김우승;조형희;김민수
    • 설비공학논문집
    • /
    • 제12권12호
    • /
    • pp.1098-1125
    • /
    • 2000
  • A review on the papers published in the Korean Journal of Air-Conditioning and Refrigerating Engineering in 1998 and 1999 has been done. Focus has been put on current status of research in the aspect of heating, cooling, ventilation, sanitation and building environment. The conclusions are as follows. 1) A review of the recent studies on fluid flow, turbomachinery and pipe-network shows that many experimental investigations are conducted in applications of impingement jets. Researches on turbulent flows, pipe flows, pipe-networks are focused on analyses of practical systems and prediction of system performance. The results of noise reduction in the turbomachinery are also reported. 2) A review of the recent studies on heat transfer analysis and heat exchanger shows that there were many papers on the channel flow with the application to the design of heat exchanger in the heat transfer analysis. Various experimental and numerical papers on heat exchanger were also published, however, there were few papers available for the analysis of whole system including heat exchanger. 3) A review of the recent studies on heat pump system have focused on the multi-type system and the heat pump cycle to utilize treated sewage as the heat source. The defrosting and the frosting behaviors in the fin-tube heat exchanger is experimentally examined by several authors. Several papers on the ice storage cooling system are presented to show the dynamic simulation program and optimal operation conditions. The study on the micro heat pipes for the cooling of high power electronic components is carried out to examine the characteristics of heat and mass transfer processed. In addition to these, new type of separate thermosyphon is studied experimentally. 4) The recent studies on refrigeration/air conditioning system have focused on the system performance and efficiency for new alternative refrigerants. New systems operating with natural refrigerants are drawing lots of attention. In addition to these, evaporation and condensation heat transfer characteristics of traditional and new refrigerants are investigated for plain tubes and also for microfin tubes. Capillary tubes and orifice are main topics of research as expansion devices and studies on thermophysical properties of new refrigerants and refrigerant/oil mixtures are widely carried out. 5) A review of the recent studies on absorption cooling system shows that numerous experimental and analytical studies on the improvement of absorber performance have been presented. Dynamic analysis of compressor have been performed to understand its vibration characteristics. However research works on tow-phase flow and heat transfer, which could be encountered in the refrigeration system and various phase-change heat exchanger, were seemed to be insufficient. 6) A review of recent studies on duct system shows that the methods for circuit analysis, and flow balancing have been presented. Researches on ventilation are focused on the measurement of ventilation efficiency, and variation of ventilation efficiency with ventilation methods by numerous experimental and numerical studies. Furthermore, many studies have been conducted in real building in order to estimate indoor thermal environments. Many research works to get some information for cooling tower design have been performed but are insufficient. 7) A review on the recent studies on architectural thermal environment and building mechanical systems design shows that thermal comfort analysis is sitting environment, thermal performance analysis of Korean traditional building structures., and evaluation of building environmental load have been performed. However research works to improve the performance of mechanical system design and construction technology were seemed to be insufficient.

  • PDF

실시간 신호제어를 위한 신경망 적용 지체최소화 주기길이 설계모형 개발 (Development of Neural Network Based Cycle Length Design Model Minimizing Delay for Traffic Responsive Control)

  • 이정윤;김진태;장명순
    • 대한교통학회지
    • /
    • 제22권3호
    • /
    • pp.145-157
    • /
    • 2004
  • 국내 실시간 신호제어시스템은 주요교차로의 검지체계에서 산출되는 포화도 정보 및 실시간 신호운영자료를 토대로 차기 주기길이를 설계하고 있다. 이러한 국내 실시간 신호제어시스템의 주기길이 설계모형에 의해 설계되는 차기주기길이는 교통량이 증가하면 주기길이도 증가한다는 주기길이 결정 기본원리를 따르고 있으나 해당 주기길이 설계모형으로 결정되는 주기길이가 과연 지체최소화 주기인지 검토가 요구된다. 또한 국내 실시간 신호제어시스템의 주기길이 설계모형에는 운영자 결정 변수가 있어 차기 주기길이 설계가 비효율적일 수 있으므로 운영자 결정 변수를 제외한 주기길이 설계모형 개발이 필요하다. 이에 본 연구에서는 (1)국내 실시간 신호제어시스템의 주기길이 설계모형을 검토하고, (2)운영자 결정변수를 제외한 주기길이 설계모형을 개발한다. 국내 실시간신호제어시스템의 주기길이 설계모형을 검토한 결과 (1)교차로의 운영상태가 비포화일 경우 지체최소화 주기보다 큰 주기길이를 설계하는 것으로 검토되었고, (2)교차로의 현재 신호주기가 90초 이상일 경우 목적 운영포화도(Target operational volume-to-capacity ratio)가 0.90을 유지하는 반면 신호주기가 90초 미만일 경우 목적운영포화도가 0.90보다 작아지는 것으로 검토되었다. 본 연구는 이러한 점을 고려, 신경망을 이용하여 운영자 결정변수를 제외한 국내 실시간 신호제어시스템을 위한 지체 최소화 주기길이 설계 모형을 개발하였다. 모형 검증결과 본 연구에서 개발된 신경망 모형은 국내 실시간 신호 제어시스템과는 달리 지체최소화 주기길이와 유사한 패턴으로 주기길이를 설계한다는 결과를 도출하였다.택배서비스시장도 성장한 것으로 나타났다. 특히 정부주도에 의한 정보화추진이 전자상거래를 촉진시켜 택배서비스시장에 영향을 미친 것으로 분석되었다.수 있는 Load Balancing System을 제안한다.할 때 가장 효과적인 라우팅 프로토콜이라고 할 수 있다.iRNA 상의 의존관계를 분석할 수 있었다.수안보 등 지역에서 나타난다 이러한 이상대 주변에는 대개 온천이 발달되어 있었거나 새로 개발되어 있는 곳이다. 온천에 이용하고 있는 시추공의 자료는 배제하였으나 온천이응으로 직접적으로 영향을 받지 않은 시추공의 자료는 사용하였다 이러한 온천 주변 지역이라 하더라도 실제는 온천의 pumping 으로 인한 대류현상으로 주변 일대의 온도를 올려놓았기 때문에 비교적 높은 지열류량 값을 보인다. 한편 한반도 남동부 일대는 이번 추가된 자료에 의해 새로운 지열류량 분포 변화가 나타났다 강원 북부 오색온천지역 부근에서 높은 지열류량 분포를 보이며 또한 우리나라 대단층 중의 하나인 양산단층과 같은 방향으로 발달한 밀양단층, 모량단층, 동래단층 등 주변부로 NNE-SSW 방향의 지열류량 이상대가 발달한다. 이것으로 볼 때 지열류량은 지질구조와 무관하지 않음을 파악할 수 있다. 특히 이러한 단층대 주변은 지열수의 순환이 깊은 심도까지 가능하므로 이러한 대류현상으로 지표부근까지 높은 지온 전달이 되어 나타나는 것으로 판단된다.의 안정된 방사성표지효율을 보였다. $^{99m}Tc$-transferrin을 이용한 감염영상을 성공적으로 얻을 수 있었으며, $^{67}Ga$-citrate 영상과 비교하여 더 빠른 시간 안에 우수한 영상을 얻을 수

무용요법이 노인의 신체적.심리적 특성에 미치는 효과 (The Effect of Dance Therapy on Physical and Psychological Characteristics in The Elderly)

  • 이영란
    • 대한간호학회지
    • /
    • 제29권2호
    • /
    • pp.429-444
    • /
    • 1999
  • This study was performed to explore the effects of a dance therapy on physical and psychological characteristics in the elderly. The design of this study was a non-equivalent pre-post test experiment. The subjects consisted of elderly persons living in a facility located in Suweon and Bucheon. Fifty eight subjects, aged between 65 and 93 years who had normal cognition, sensory function, balance, and resting blood pressure. They underwent tests of balance, flexibility, muscle strength, depression, and anxiety as baseline data before dance therapy, and at 6th week and at the end of the 12nd week after following dance therapy. Twenty seven elderly persons were assigned to the experimental group and participated with the dance therapy between April and July, 1998. The dance therapy was developed by the author with the help of a dance therapist and a physiatrist. This therapy was based on the Marian Chace's dance therapy and Korean traditional dance with music. The dance therapy consists of 50 minutes session, 3 times a week for 12 weeks. One session was consisted of warming-up, expression, catharsis, sharing, and closing stage. The intensity of the dance therapy was at the 40 % of age-adjusted maximum heart rates. Data were analysed with mead standard deviation, Chi-square test, unpaired t-test, repeated measures ANOVA, and Bonferroni multiple regression using SAS program. 1. The results related to the physical characteristics were as follows : 1) The balance (standing on one leg, walking on the balancing bar), flexibility and muscle strength (knee extensor, knee flexor, ankle plantarflexor and dorsiflexor) of the experimental subjects significantly increased over time mere than that of the control subjects. 2) The experimental group had significantly higher score for balance, flexibility, muscle strength of knee extensor, and knee flexor than the control group at the 12nd week after dance therapy. 3) The experimental group had significantly higher score for muscle strength of ankle dorsiflexor and plantarflexor than the control group at the 6th week and the 12nd week after dance therapy. 2. The results related to psychological characteristics were as follows : 1) Scores of Geriatric Depression Scale, Hamilton Depression Rating Scale, and Zung's Self-rating Anxiety Scale of the experimental group were significantly decreased over time more than that of the control group. 2) The experimental group had significantly lower score for depression than the control group at the 12nd week after dance therapy. 3) The experimental group had significantly lower score for anxiety than the control group at the 6th week and the 12nd week after dance therapy. The findings showed that the dance therapy could be effective in improving the balances, flexibility, and muscle strength of lower limb, and effective in decreasing the depression and anxiety of the elderly. Additional merits of the dance therapy would be inexpensiveness, easy accessibility, and increasing interpersonal relationship. It can be suggested that the dance therapy is effective in the health promotion of the elderly.

  • PDF

과학과 미술 통합프로그램이 초등과학영재의 뇌 활성에 미치는 효과 (The Effects of Science and Art Integrated Program on Brain Activity of Gifted Students in Science)

  • 권영식;이길재
    • 한국초등과학교육학회지:초등과학교육
    • /
    • 제32권4호
    • /
    • pp.567-580
    • /
    • 2013
  • This study is to activate gifted students' brains for creativity ability and also an integrated science and art teaching program. The learning programs integrating science and art, which have 30 periods and 10 topics on art and the knowledge of science, were developed dependant on five steps - observing, having interests and curiosity, experimental designing and performing, internalizing, and expressing in an arts-based manner. This programs were applied to 20 senior gifted students in Y Elementary School in Gyeonggi province, by one group pretest-posttest design. The results from these integrated programs of science and art are as follows: First, in the performance of science tasks, prefrontal lobe(F7, FT7) of left brain increase the relative power of theta wave, whereas in the performance of drawing tasks increase the relative power of beta wave in prefrontal lobe(FP1) of left brain, bilateral frontal(F7, F3, Fz, F4, F8, FT7, FC3, FCz), bilateral temporal(T7, TP7, TP8, P7), parietal lobe of left brain(CP3, CPz, P3, Pz), bilateral occipital(O1, Oz, O2). Second, in the performance of science tasks, the relative power of beta wave activity in the left temporal lobe(T7) of the brains of talented students in science significantly decreased whereas it was greatly activated in another part, the left frontal lobe(F3) of the brain (p<.05). Third, in the performance of drawing tasks, the relative power of theta wave activity in five areas of the brain, namely the left temporal lobe(T7), the left frontal lobe(F3), the right frontal lobe(F4), and the left and right parietal lobes of gifted students in science who took the course of the integrated programs, was considerably increased statistically(p<.05). On top of that, these programs were especially effective in balancing the symmetrical development of both cerebral hemispheres by multiplying theta wave activity in the frontal lobes(F3, F4) and the parietal lobes(CP3, P3, P4), which are particularly related to creative thinking. According to the results of this study of brain-based teaching strategies combining science and art, it is an effective program to develop overall activate gifted students' brains for creativity ability. This is expected to be utilized to activate the brain areas for creativity of gifted students in science.

수출인프라강화사업이 식품유통기업 수출에 미치는 정책효과 분석 (An Analysis of Policy Effects of Export Infrastructure Strengthening Program on Export of Food Distribution Companies)

  • 황성혁;지성태
    • 유통과학연구
    • /
    • 제16권1호
    • /
    • pp.87-99
    • /
    • 2018
  • Purpose - The Export Infrastructure Strengthening Program(EISP) is a project to expand exports of agri-food products through providing customized export information to food distribution companies and supporting overseas information activities. A total of 39.6 billion won was provided by 2016. So, the purpose of this study is to analyze whether EISP is effective for expanding exports of agri-food products. Research design, data, and methodology - A simple average difference between the export performance of the policy beneficiaries and the non-policy beneficiaries can be biased if the export capacity or inherent characteristics of the enterprise are not taken into consideration. In order to solve the problem of such a bias, the propensity score matching(PSM) method has been employed in this study. PSM is a method of converting the characteristics of an export company into an index through logit analysis and then reducing the matching to one dimension to improve the accuracy of the performance measurement. Results - The balancing test was conducted to determine how the characteristics of the policy beneficiary group and the matched policy non-beneficiary group corresponded to each other. As a result of the test, we could not reject the null hypothesis that there was no difference between the two groups, so that after the matching, the two groups were similar and the explanatory variables were well controlled. Using the nearest neighbor matching with propensity score estimating through logit analysis, we estimated average treatment effect on the treated(ATT). The food companies participating the EISP had the effect of increasing the exports of $ 5.88 million. As a result, the number of export contracts increased by 11.77, the number of exporting countries by 7.52, the number of export items by 47.51, and the number of buyers' consultation by 3.50. And overseas marketing expenses increased by 35.92 million won. Except for the number of export contracts, other export performance results showed statistically significant results. Conclusions - As the EISP has a positive effect on the expansion of agro-food exports, efforts should be made to find out the limitations or problems of the policy in the future and to make a greater contribution to the increase of exports.

분산 시각미디어 검색 프레임워크를 위한 결함허용 시스템 설계 (The Design of Fault Tolerant System for Semantic Web based Visual Media Retrieval Framework)

  • 진휴정;심준용;김세창;원재훈;김정선
    • 한국정보과학회:학술대회논문집
    • /
    • 한국정보과학회 2006년도 가을 학술발표논문집 Vol.33 No.2 (B)
    • /
    • pp.228-232
    • /
    • 2006
  • Ontology를 이용한 분산 시각미디어 검색 프레임워크인 HERMES(The Retrieval Framework for Visual Media Service)[1][2]는 보다 정확한 시각미디어 정보를 제공하고 웹서비스(Web Services)를 적용하여 HERMES/Provider[1][2]의 자율성을 보장한다. 웹기반의 분산 환경에서 Visual Media Data에 대한 지능적인 검색을 위하여 Meta Data와 Ontology를 이용하고 이기종간 통신을 위한 웹서비스를 제공하는 HERMES/ Broker[1][2]에서 예상치 못한 문제가 발생할 경우 문제를 해결할 수 있는 방법이 제시되지 않았다. 일반적으로 웹 서비스를 제공하는 서버에서 발생되는 결함은 해당 웹 서비스를 이용하여 개발되는 어플리케이션의 갑작스런 중단이나 오류의 원인이 된다. 따라서 결함을 해결할 수 있는 대책이 필요하며 HERMES의 Broker 서버 또한 웹 서비스의 결함이 발생하더라고 이를 효과적으로 해결하여 클라이언트에게 웹 서비스를 정상적으로 제공할 수 있는 결함허용 시스템 도입이 매우 중요하다. 때문에 HERMES 프레임워크가 클라이언트에게 신뢰성과 안정성이 보장된 웹 서비스의 제공을 위해서 Broker 서버에서 발생할 수 있는 결함을 효과적으로 극복할 수 있는 메커니즘이 필요하다. 본 논문에서는 Broker 서버 에서 웹 서비스와 관련된 결함이 발생하더라고 올바르게 운영될 수 있으며 분산 이미지 검색 프레임워크인 HERMES의 구조적 특성에 적합한 결함허용 시스템 설계 기법을 제안하여 HERMES 프레임워크가 클라이언트에게 투명성 있는 서비스를 제공하고 높은 신뢰성과 안정성이 확보될 수 있도록 구성하고자 한다. Query 수행을 여러 서버로 분산처리하게 함으로써 성능에 대한 신뢰성을 향상 시킬 수 있는 Load Balancing System을 제안한다.할 때 가장 효과적인 라우팅 프로토콜이라고 할 수 있다.iRNA 상의 의존관계를 분석할 수 있었다.수안보 등 지역에서 나타난다 이러한 이상대 주변에는 대개 온천이 발달되어 있었거나 새로 개발되어 있는 곳이다. 온천에 이용하고 있는 시추공의 자료는 배제하였으나 온천이응으로 직접적으로 영향을 받지 않은 시추공의 자료는 사용하였다 이러한 온천 주변 지역이라 하더라도 실제는 온천의 pumping 으로 인한 대류현상으로 주변 일대의 온도를 올려놓았기 때문에 비교적 높은 지열류량 값을 보인다. 한편 한반도 남동부 일대는 이번 추가된 자료에 의해 새로운 지열류량 분포 변화가 나타났다 강원 북부 오색온천지역 부근에서 높은 지열류량 분포를 보이며 또한 우리나라 대단층 중의 하나인 양산단층과 같은 방향으로 발달한 밀양단층, 모량단층, 동래단층 등 주변부로 NNE-SSW 방향의 지열류량 이상대가 발달한다. 이것으로 볼 때 지열류량은 지질구조와 무관하지 않음을 파악할 수 있다. 특히 이러한 단층대 주변은 지열수의 순환이 깊은 심도까지 가능하므로 이러한 대류현상으로 지표부근까지 높은 지온 전달이 되어 나타나는 것으로 판단된다.의 안정된 방사성표지효율을 보였다. $^{99m}Tc$-transferrin을 이용한 감염영상을 성공적으로 얻을 수 있었으며, $^{67}Ga$-citrate 영상과 비교하여 더 빠른 시간 안에 우수한 영상을 얻을 수 있었다. 그러므로 $^{99m}Tc$-transierrin이 감염 병소의 영상진단에 사용될 수

  • PDF

CORBA-ORB, JAVA-RMI, 소켓을 이용한 그룹 통신의 구현 및 성능 분석 (Implementation and Performance Analysis of the Group Communication Using CORBA-ORB, JAVA-RMI and Socket)

  • 한윤기;구용완
    • 인터넷정보학회논문지
    • /
    • 제3권1호
    • /
    • pp.81-90
    • /
    • 2002
  • 대다수의 인터넷 기반의 분산 어플리케이션이나 클라이언트/서버의 응용은 부하균등, 통신 지연, 네트워크 결함 등의 문제점을 처리하여 사용자에게 서비스해야 한다. 또한 화상 회의, VOD, 병행 소프트웨어 공학과 같은 정교한 응용프로그램들은 추상적인 그룹 통신을 필요로 한다. 이러한 페러다임들을 현재의 CORBA 버전들은 적절히 수용하지 못한다. CORBA는 주로 Point-to-Point통신을 하기 때문에 분산 시스템에서 예측 행위를 하는 신뢰성 있는 응용 기술에 대한 구현은 지원하지 않는다. 따라서, 본 논문에는 분산 컴퓨팅 환경 하에서 CORBA-ORB를 이용한 그룹 통신, JAVA-RMI를 이용한 그룹 통신, 소켓을 이용한 그룹 통신 등을 설계 및 구현을 하였으며, 이에 따른 성능 분석을 실시하였다. 성능 분석은 객체의 증가에 따른 지연시간으로 측정하였고 CORBA의 ORB를 이용한 그룹 통신의 경우 평균은 14.5172msec, JAVA의 RMI를 이용한 그룹 통신의 경우 평균은 21.4085msec, 소켓을 이용한 그룹 통신의 경우 평균은 18,0714msec가 나왔다. 멀티캐스트와 UDP를 이용한 그룹 통신은 각각 0.2735msec, 0.2157msec로 측정되었음을 알 수 있다. 논문의 결과로 객체의 증가에 따라 CORBA-ORB 그룹 통신의 성능향상을 보였다. 본 연구는 결함 허용 클라이언트/서버 시스템. 그룹웨어, 텍스트 검색엔진. 금융 정보 시스템 등에 적용 가능하다.

  • PDF