• Journal of Biosystems Engineering
• /
• v.43 no.2
• /
• pp.94-102
• /
• 2018

Purpose: In this study, a maintenance free super-capacitor battery charging system based on the photovoltaic module, to be used in agricultural electric carriers, was developed and its charging characteristics were studied in detail. Methods: At first, the electric carrier system configuration is introduced and the electric control components are presented. The super-capacitor batteries and photovoltaic module used in the experiment are specified. Next, the developed charging system consisting of a constant current / constant voltage Buck converter as the charging device and a super-capacitor cell as a balancing device are initiated. The proposed circuit design, a developed PCB layout of each device and a proportional control to check the current and voltage during the charging process are outlined. An experiment was carried out using a developed prototype to clarify the effectiveness of the proposed system. A power analyzer was used to measure the current and voltage during charging to evaluate the efficiency of the energy storage device. Finally, the conclusions of this research are presented. Results: The experimental results show that the proposed system successfully controls the charging current and balances the battery voltage. The maximum voltage of the super-capacitor battery obtained by using the proposed battery charger is 16.2 V, and the maximum charging current is 20 A. It was found that the charging time was less than an hour through the duty ratio of 95% or more. Conclusions: The developed battery charging system was successfully implemented on the agricultural electric carriers.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.7
• /
• pp.95-102
• /
• 2014

There are a variety of structures below the surface are buried. In particular, if It is experiencing problems in the city gas pipe or electrical wire, our safety would be greatly jeopardized. Therefore, the underground structures which encounter a variety of pollutants are highly sensitive to corrosion. So if you are not identify the degree of corrosion, it can lead to large accidents such as gas leakage. Until now, person visit directly every underground structure to measure and record manually, but This approach requires a lot of human and material resources and the continuity of management. Therefore, the research to find out the risk factors quickly via the continuous management is needed, and in this paper the structures management systems in the vehicle being moved by combining ICT underground structures for state information wirelessly collects and analyzes system is proposed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.8
• /
• pp.879-885
• /
• 2008

A rotordynamic analysis was performed with a decant-type centrifuge, which is a kind of industrial centrifuge. The system is composed of screw rotor, bowl rotor, driving motors, gear box, and support rolling element bearings. These rotors have a rated speed of 4300 rpm, and were modeled utilizing a rotordynamic FE method for analysis, which was verified through 3-D FE analysis. Design goals are to achieve wide separation margins of lateral critical speeds, and favorable unbalance responses of the rotor in the operating range. Then, a complex analysis rotordynamic analysis of the system was carried out to evaluate its forward synchronous critical speeds and mode shapes, whirl natural frequencies, and unbalance responses under various balance grade. As a result of analysis, the rotordynamic analysis performed by separating a screw rotor and bowl rotor may cause an error in predicting critical speed of entire system. Therefore, the rotordynamic analysis of a coupled rotor combining a screw and bowl rotor must be performed in order to more accurately estimate dynamic characteristics of the decanter-type centrifuge as presented in this paper. Also, rolling element bearings with suitable stiffness should be selected to keep enough separation margin. In addition, in establishing balance grade of a screw and bowl rotor, ISO G2.5 balance grade is more recommended than ISO G6.3, in particular balancing correction of a screw rotor based on ISO G2.5 grade is strongly recommended.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.4
• /
• pp.73-84
• /
• 2015

Electricity generation using fossil fuels has caused environmental pollution. To solve this problem, research on new renewable energy sources (solar, wind power, geothermal heat, etc.) to replace fossil fuels is ongoing. These devices are able to generate power consistently. However, they have many weaknesses, such as high installation costs and limits to possible setup environments. Therefore, an active study on piezoelectric harvesting technology that is able to surmount the limitations of existing energy technologies is underway. Piezoelectric harvesting technology uses the piezoelectric effect, which occurs in crystals that generate voltage when stress is applied. Therefore, it has advantages, such as a wider installation base and lower technological costs. In this study, a piezoelectric harvesting device imitating seaweed, which has a consistent motion caused by fluid, is used. Thus, it can regenerate electricity at sea or on a bridge pillar, which has a constant turbulent flow. The components of the device include circuitry, springs, an electric generator, and balancing and buoyancy elements. Additionally, multiphysics analysis coupled with fluid, structure, and piezoelectric elements is conducted using COMSOL Multiphysics to evaluate performance. Through this program, displacement and electric power were analyzed, and the actual performance was confirmed by the experiment.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.44 no.4 s.316
• /
• pp.101-108
• /
• 2007

Parallel processing algorithms, coupled with advanced networking and distributed computing architectures, improve the overall computational performance, dependability, and versatility of a digital signal processing system In this paper, novel parallel algorithms are introduced and investigated for advanced sonar algorithm, conventional matched-field processing (CMFP). Based on a specific domain, each parallel algorithm decomposes the sequential workload in order to obtain scalable parallel speedup. Depending on the processing requirement of the algorithm, the computational performance of the parallel algorithm reveals different characteristics. The high-complexity algorithm, CMFP shows scalable parallel performance on the array of DSP processors. The impact on parallel performance due to workload balancing, communication scheme, algorithm complexity, processor speed, network performance, and testbed configuration is explored.

• Progress in Superconductivity
• /
• v.7 no.1
• /
• pp.6-10
• /
• 2005

We have studied feasibility of single-layer second-order $high-T_c$ SQUID gradiometers in magnetocardiography. We have measured human cardiomagnetic signals using a short-baseline (5.8 mm) single-layer second-order YBCO gradiometer in partially shielded environments. The gradiometer has an overall size of $17.6\;mm{\times}6\;mm$ and contains three parallel-connected pickup coils which are directly coupled to a step-edge junction SQUID. The gradiometer showed an unshielded gradient noise of $0.84\;pT/cm^2/Hz^{1/2}$ at 1 Hz, which corresponds to an equivalent field noise of $280\;fT/Hz^{1/2}$. The balancing factor was $10^3$. Based on the same design rules as the short-baseline devices, we have studied fabrication of 30 mm-long baseline gradiometers. The devices had an overall size of $70.2\;mm{\times}10.6\;mm$ with each pickup coil of $10\;mm{\times}10\;mm$ in outer size. As Josephson elements we made two types of submicron bridges, which are variable thickness bridge (VTB) and constant thickness bridge (CTB), from $3\;{\mu}m-wide$ and 300 nm-thick YBCO lines with a thin layer of Au on top by using a focused ion beam (FIB) patterning method. VTB was 300 nm wide, 200 nm thick, 30 nm long with Au removed and CTB 100 nm wide and 30 nm long. In temperature-dependent critical currents, $I_c(T)$, VTB showed an nonmetallic barrier-type behavior and CTB an SNS behavior. We believe that those characteristics are ascribed to naturally formed grain boundaries crossing the bridges.

• Korean Journal of Human Ecology
• /
• v.23 no.4
• /
• pp.665-680
• /
• 2014

The purpose of this study was to develop the construction process of orthopedic compression garments (OCG) for balancing of the left and right lumbar muscle power and strength to prevent low back pain. One male subject having low back pain was involved for investigating of the lumbar muscle power. EMG (Telemyo DTS2, Noraxon, U.S.A) was measured with/ without 3 types of waist assistant belt around the waist area of the subject. Based on the electromyogram value of left and right body, OCG were constructed as follows. Firstly, stretchable t-shirts type with supportive waist belt was selected for the convenience of wearing and laundering the OCG. The design lines of the front and back waist parts were created depending on the anatomy of the torso. Secondly, 3D pattern was developed using 3D Clo, RapidForm XOR, 2C-AN, and Yuka CAD program to increase the fit of the OCG. Finally, stretchable power-net was layered as linings in two ways, a single lining and double layered linings, and evaluated measuring lumbar muscle EMG by five subjects with low back pain. As the results, they were effective to balance the left and right lumbar muscle power and strength. Also the OCG with the double layered power-net lining was superior to the one layered lining in terms of fit and comfort.

• Journal of Korean Academy of Nursing
• /
• v.46 no.2
• /
• pp.260-270
• /
• 2016

Purpose: This study was conducted to develop a program to help emergency nurses overcome compassion fatigue, and to analyze the effects of the program. Methods: A nonequivalent control group pretest-posttest design was used. There were 14 participants in the experimental group and 18 subjects in the control group. The program was comprised of five, weekly 80-minute sessions including understanding and assessment of compassion fatigue, enhancing positive affect, balancing work-life, planning self care, training in relaxation techniques and cognitive restructuring, and getting social support. Research variables were ego-resiliency, compassion satisfaction and compassion fatigue of the ProQOL 5, and salivary cortisol. Data were analyzed using Chi-square test, independent t-test, and paired t-test. Results: The first hypothesis, "There will be a difference in scores for ego resiliency between the experimental group and the control group". was not supported. The second hypothesis, "There will be a difference in scores for compassion satisfaction between the experimental group and the control group" was supported (t=2.15, p=.046). The third hypothesis, "There will be a difference in scores for compassion fatigue between the experimental group and the control group" was not supported. Conclusion: The first program for emergency nurses to overcome compassion fatigue in Korea was effective in increasing emergency nurses' compassion satisfaction and decreasing salivary cortisol level in the experimental group. Therefore, this program for overcoming compassion fatigue is useful to increase emergency nurses' compassion satisfaction. However replication studies of short-term intensive program reflecting emergency nurses' opinion are needed.

• Journal of Broadcast Engineering
• /
• v.16 no.2
• /
• pp.258-273
• /
• 2011

This paper designs and implements a multi-view 3D video player system which is operated faster than existing video player systems. The structure for obtaining the near optimum speed in a multi-processor environment by parallelizing the component modules is proposed to process large volumes of multi-view image data at high speed. In order to use the concurrency of bottleneck, we designed image decoding, synthesis and rendering modules in a pipeline structure. For load balancing, the decoder module is divided into the unit of viewpoint, and the image synthesis module is geometrically divided based on synthesized images. As a result of this experiment, multi-view images were correctly synthesized and the 3D sense could be felt when watching the images on the multi-view autostereoscopic display. The proposed application processing structure could be used to process large volumes of multi-view image data at high speed, using the multi-processors to their maximum capacity.

• The KIPS Transactions:PartD
• /
• v.12D no.7 s.103
• /
• pp.1007-1016
• /
• 2005

A key issue for process language design is balancing the need for semantic richness with the need for ease of use. Most process modeling languages fail to satisfy above two conflicting aspects, which is an impediment to the widespread adoption of process modeling languages in the software industry despite of a variety of software process language studies. This paper describes a process modeling language RAiSE attempting to resolve such problem and presents the result of applying RAiSE to a well-known benchmark process, ISPW-6 software process example. RAiSE provides rigorous, yet clear semantics through combing essential features in various modeling paradigms and defining them in a well-structured graphical notation. Process models represented in RAiSE are interpreted and enacted by process engine implemented using CLiPS, a rule based expert system tool.