• Journal of the Korean Vacuum Society
• /
• v.11 no.2
• /
• pp.87-96
• /
• 2002

Outgassing from such sources as paints, coatings, adhesives and other non-metallic surfaces can contaminate satellites, especially second surface mirror and optical lens, it cause satellite to fail in own missions. The vacuum bake-out test using high temperature(more than $85 ^{\circ}C$)and high vacuum(less than $5.0{\times}1-^{-3}$ Pa) certify that the components of satellite work properly and can survive and operate in space environment like high vacuum. In the bake-out chamber installed at SITC of KARI, Rotary vacuum pump and Booster pump produce low vacuum of 5.0 Pa, and then two cryopumps produce high vacuum of below $5.0{\times}10^{-3}$ Pa. Also 48 ceramic heaters were provided to simulate high temperature. During the vacuum bake-out test, we detected contaminants using RGA(Residual Gas Analyzer) and measure the outgassing rate of the contaminant using the TQCM(Thermoelectric Quartz Crystal Microbalance). Also, IR/UV Spectrometer and witness plate be used to certify that the components were suitable for the spacecraft. This paper includes the preparation and procedures of the bake-out test for SAR(Solar Array Regulator) and MLI(Multi Layer Insulator), which were the components of the spacecraft. Especially, we discussed the methods and results of the contamination measurement. In the bake-out for SAR, the contamination was measured continuously although it was on the decrease from TQCM results. And RCA established that it is a highly polymerized compound. In the MLI bake-out using RGA and witness plate, we didn't detect any contamination materials.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.3
• /
• pp.247-257
• /
• 2001

In an effort to improve the dent resistance of exterior body panels at a reduced steel thickness, the bake hardenable steels added Ti or Nb with tensile strength of 35Kgf/$\textrm{mm}^2$ were investigated. The bake hardenability increased with the annealing temperature and solute carbon content. Bake hardening of 3 to 5Kgf/$\textrm{mm}^2$ was obtained in steels with a controlled solute carbon concentration range from 6 to 10ppm. The galvannealing temperature and time had little influence on the bake hardenability. The Fe-Zn alloying reaction of 35Kgf/$\textrm{mm}^2$ BH steel was remarkably retarded due to a 0.07%P addition. The optimum galvannealing temperatures of 35Kgf/$\textrm{mm}^2$ BH steel were ranged from 520 to 56$0^{\circ}C$ in view of the Fe content and powdering resistance. The cross-section and planar views of the galvannealed coatings to characterize morphology development were discussed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.05a
• /
• pp.597-600
• /
• 2001

ETSI has dominated in the field of mobile technology standardization, for instance GSM. The reasons why ETSI has a dominating power on standardization of the technology are as fellows. Firstly, ETSI has thoroughly monitored the external environment surrounding ETSI standardization activities, and has positioned well in this context. And secondly, ETSI has established flexible organizational structure and various working methods e.g. Bake-off. In this paper, Bake-off will be analyzed for drawing implications to working methods of Telecommunication Forums in our nations.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.708-713
• /
• 2008

Various kinds of contaminant are generated from many kinds of interior construction materials, furniture and life articles. People of today living indoor most of the time are exposed to these kinds of contaminant. In this connection, people are exerting their efforts to reduce the occurrence of contaminant from the interior finish materials. And it is the actual condition that research is being actively made on the method of reducing contaminant by performing bake-out for newly constructed housings. Bake-out is the method of temporarily increasing the generation of the harmful contaminant quantity including VOCs and Formaldehyde emitting from construction materials or finish materials by increasing the interior temperature of the newly constructed buildings or improved or repaired buildings, and then removing it by mobilizing ventilation system. In this study, the researcher measured the effect of reduced concentration according to ventilation or non-ventilation of the newly constructed but not yet resident public housings during the bake-out in order to grasp the effect of reduced interior air contaminant according to the elapse of timeat the time of bake-out.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.2
• /
• pp.91-100
• /
• 2012

This study analysis the effect of various temperatures (20, 35 and $50^{\circ}C$) on the formaldehyde emission from wood composites, which were particleboard (PB), medium density fiberboard (MDF), high density fiberboard (HDF) and laminated HDF (L-HDF) by Japanese desiccator method. Also, to reduce formaldehyde emission by wood composites, it has been suggested that undergo a bake-out conditions. On average, the level of formaldehyde emission increased many times with a $15^{\circ}C$ increase in temperature from 20 to $35^{\circ}C$ for PB, MDF, HDF and L-HDF, respectively. Formaldehyde emissions from wood composites could be expected to increase with increasing ambient temperature. At $35$ for 28 days bake-out treatment of boards, the free formaldehyde emission reduced 67.8% (PB), 40.1% (MDF), 37.8% (HDF), and 35.2% (L-HDF). On the other hand, after the bake-out at $50^{\circ}C$ for 28 days, the formaldehyde concentration decreased by 88.2, 66.9, 62.2 and 59.3% of the concentration before the bake-out for PB, MDF, HDF and L-HDF, respectively. An interesting of the bake-out treatment at $50^{\circ}C$ after 14 days, formaldehyde emission grade of PB & MDF down $E_2$ to $E_1$, and HDF & L-HDF down $E_1$ to $E_0$.

• Journal of the Korean housing association
• /
• v.17 no.4
• /
• pp.111-117
• /
• 2006

The harmfulness of HCHO and VOCs from construction material and furniture has been increased gradually. It must be need to prevent pollution materials' accumulation indoor effectively and to remove very small amount of harmful pollution materials in various plans, because these kinds of pollution materials greatly affect human body, Therefore, this study is focused to find out the improvements of Indoor Air Quality in execution of natural ventilation and bakeout to reduce indoor chemical pollution materials or not. After effects of indoor air quality by natural ventilation and bake-out being examined, it is follows the conclusion. As for the density change of TVOC and Toluene according to time lapse, in case the middle and high-story areas have bake-out, the density increased once, but it showed the gradual decrease after bake-out was stopped, and it was shown that it exceeded the standards recommended for newly built apartment. The bake-out is effective to discharge the HCHO and TVOC from the construction material and the furniture, and the natural ventilation is effective remove the indoor pollution materials.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.131-131
• /
• 2012

압전재료는 그 특성상 항공우주분야에서 활용범위가 넓어지고 있는데, 특히 진동제어 분야에 널리 이용되고 있다. 최근에는 위성카메라의 영상 품질개선을 위한 구동기(actuator) 연구도 진행 중이다. 그러나 위성체가 작동하는 우주환경인 고진공상태에서는 각 부품에서 발생할 수 있는 outgassing으로 인해 위성체가 오염되어 위성임무 실패를 초래할 수도 있다. 따라서 지상에서 위성체 부품에 대해 고온($60^{\circ}C$)과 고진공(5.0 E-03 Pa 이하)의 상태를 모사하여 오염물질을 제거함으로써 outgassing 발생을 막고, 오염근원을 검출할 수 있는 bacuum bake-out 시험이 필요수적이다. 압전체의 위성부품 활용성 연구를 위하여 bake-out 챔버를 이용하여 오염측정에 관한 연구를 수행하였다. Vacuum bake-out 시험시에는 TQCM을 사용하여 발생하는 오염물질의 방출률을 측정한다. 아울러, 압전체에 대한 시험 전후의 압전특성을 비교 분석하여 진공 및 온도 환경하에서의 특성 변화를 관찰하였다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.37-44
• /
• 2004

Automotive company has been endeavoring to develop high strength steels to get higher fuel efficiency of car since the oil shortage in 1970s and to cope with the recent strict environmental regulation. Outer panels(Hood, Roof, Door and Fender) for automobile require higher dent resistance. Bake-hardenable(BH) steels are known as useful for their high deep drawability and high dent resistance. Recently BH steels are increasingly adapted for outer panel use due to their high drawability and high dent resistance. In this study effect of temper rolling on formability (textures, r value) and bake hardenability is investigated fur improving characteristic of bake-hardenable steels.

• Journal of Korea Foundry Society
• /
• v.24 no.4
• /
• pp.231-237
• /
• 2004

Bake hardenable steel utilizes the phenomenon of strain aging to provide an increase in the yield strength of formed components. An increase of the carbon content will improve the bake hardening response: more solutes are available to pin mobile dislocations and to form the clusters more rapidly. But aging resistance decrease as increasing solute carbon. In order to under-stand the compatibility between bake hardenability and aging resistance. The optimum solute carbon control methods during manufacture should be determined. In this paper, the effect of continuous heat cycle conditions such as soaking temperature, rapid cooling start temperature, cooling rate on BH(Bake Hardenability), AI(Aging Index), YP-El(Yield Point Elongation) and other mechanical properties have been investigated. and following results were obtained. In the case of soaking temperature, BH increases with higher soaking temperature because of NbC $dissolution(830^{\circ}C)$, Therefore the solute carbon and BH at $850^{\circ}C$ and $870^{\circ}C$ are higher than these at $810^{\circ}C$. But BH at $870^{\circ}C$ is a little lower than that at $850^{\circ}C$ owing to the ferrite grain size. The measurement of amount of dissolution C using IFT(Internal Friction Test) can explain the relation of solute carbon and BH.

• Journal of the Mineralogical Society of Korea
• /
• v.31 no.2
• /
• pp.67-73
• /
• 2018

The objective of this study was to investigate the application of sulfate solvents for the economic and eco-friendly leaching of valuable metals from Au concentrate using an acid bake-water leaching system (AWS). AWS experiments were performed using an electric furnace with various baking temperatures ($100-500^{\circ}C$) and sulfate solvents ($H_2SO_4$, $K_2SO_4$, $(NH_4)_2SO_4$, $MgSO_4$, and $CaSO_4$). The efficiency of the valuable metal leaching increased as the baking temperature was increased to $400^{\circ}C$. Based on the AWS leaching time experiments, the maximum leaching rate occurred with the aqueous $(NH_4)_2SO_4$ solvent. This study demonstrates that aqueous $(NH_4)_2SO_4$ could be used as an effective solvent for valuable metal leaching using an AWS.