• Journal of Biosystems Engineering
• /
• v.43 no.1
• /
• pp.1-13
• /
• 2018

Purpose: The development of compact tractors that can be used in dry fields, greenhouses, and orchards for pest control, weeding, transportation, and harvesting is necessary. The development and performance evaluation of power transmission units are very important when it comes to tractor development. This study evaluates the performance of a driving power transmission unit of a 50 kW multi-purpose narrow tractor. Methods: The performance of the transmission and forward-reverse clutch, which are the main components of the driving power transmission unit of multi-purpose narrow tractors, was evaluated herein. The transmission performance was evaluated in terms of power transmission efficiency, noise, and axle load, while the forward-reverse clutch performance was evaluated in terms of durability. The transmission's power transmission efficiency accounts for the measurement of transmission losses, which occur in the transmission's gear, bearing, and oil seal. The motor's power was input in the transmission's input shaft. The rotational speed and torque were measured in the final output shaft. The noise was measured at each speed level after installing a microphone on the left, right, and upper sides. The axle load test was performed through a continuous equilibrium load test, in which a constant load was continuously applied. The forward-reverse clutch performance was calculated using the engine torque to axle torque ratio with the assembled engine and transmission. Results: The loss of power in the transmission efficiency test of the driving power unit was 6.0-9.7 kW based on all gear steps. This loss of horsepower was equal to 11-18% of the input power (52 kW). The transmission efficiency of the driving power unit was 81.5-89.0%. The noise of the driving power unit was 50-57 dB at 800 rpm, 70-77 dB at 1600 rpm, and 76-83 dB at 2400 rpm. The axle load test verified that the input torque and axle revolutions were constant. The results of the forward-reverse clutch performance test revealed that hydraulic pressure and torque changes were stably maintained when moving forward or backward, and its operation met the hydraulic design standards. Conclusions: When comprehensively examined, these research results were similar to the main driving power transmission systems from USA and Japan in terms of performance. Based on these results, tractor prototypes are expected to be created and supplied to farmhouses after going through sufficient in-situ adaptability tests.

• The Journal of the Korea Contents Association
• /
• v.11 no.1
• /
• pp.317-328
• /
• 2011

Logistic system and methods of the transportation have been changed rapidly by the variety of the logistics environment. It is necessary to analyze the efficiency of Korean trucking companies for enhancing the competitive power and operating. This paper will describe the analysis of the efficiency of the trucking companies with DEA models. By the CCR and the BCC models, which are in parts of DEA model, the efficiency and RTS(Return To Scale) of forty two selected trucking companies were studied. It was also analyzed how the study the input-output variables were effected. And then, some of the forty two trucking companies were shown as the benchmark. As the result of analysis on the two models, seven companies won the score '1' on CCR model and seventeen companies on BCC model. Moreover, this study showed that reducing the total asset out of input variables, and raising the sales profit out of the output variables played a main role to increase the efficiency of the trucking companies highly.

• Environmental and Resource Economics Review
• /
• v.20 no.1
• /
• pp.1-31
• /
• 2011

By employing Environmental Input-Output Table 2005, which has 76 intermediate sector and 21 energy sources, this paper analyses the flow of energy demand and $CO_2$ after estimating an induced $CO_2$ emissions from 76 industrial sectors. Index of $CO_2$ intensity($CO_2/GDP$) and other index of $CO_2$ intensity($CO_2/calory$) showed that final demand sector uses more high calory energy source. Intermediate sector used less environmental friendly energy source and emit more $CO_2$ at same calory. Industries those has high induced $CO_2$ emissions are Thermal Power($32.587CO_2-g/Won$), Cement($10.370CO_2-g/Won$), Road Transportation($7.255CO_2-g/Won$), Cokes and Other Coal Products($5.791CO_2-g/Won$), Steam and Hot water supply, Sewage, Sanitary services($4.575CO_2-g/Won$). It is shown that industry such as Iron and Steel which has low $CO_2$ intensity, high backward linkage effect and high forward linkage effect makes high induced $CO_2$ emissions. Environmental load and $CO_2$ emissions in overall economy will decrease when not high $CO_2$ intensity industry but also low $CO_2$ intensity industry makes lower $CO_2$ intensity.

• Journal of Navigation and Port Research
• /
• v.41 no.6
• /
• pp.373-380
• /
• 2017

Operational errors caused by human factors, which is the major cause of marine accidents, include lack of knowledge, misunderstanding knowledge, and inadequate procedures. Recently, the type of propulsion mounted on KCG cutters has been diversified. In particular, the water jet propulsion unit, which was mainly installed in small boats, have been gradually expanded to medium and large size Coast Guard cutters, reaching 50% of the total. Axes types are divided into 2 to 4, and the bucket types are divided into Double Reverse Bucket(DRB) and Single Reverse Bucket(SRB); in these, the backward and steering control methods are completely different. Diversification of these operating systems can increase factors causing human error by the ships' operators. However, there is a lack of research on the maneuvering methods, considering the inherent active characteristics of each type of water jet. In this paper, we analyze the sideway method suitable for the condition of Coast Guard Exclusive wharf without assistance, based on the astern performance of each type. Then, a ship handling simulator was used for the experiment; they compared and verified through interviews of captains.

• Particle and aerosol research
• /
• v.15 no.3
• /
• pp.91-104
• /
• 2019

In this study, hourly measurements of $PM_{2.5}$ and its major chemical constituents such as organic and elemental carbon (OC and EC), and ionic species were made between January 15 and February 10, 2018 at the air pollution intensive monitering station in Gwangju. In addition, 24-hr integrated $PM_{2.5}$ samples were collected at the same site and analyzed for OC, EC, water-soluble OC (WSOC), humic-like substance (HULIS), and ionic species. Over the whole study period, the organic aerosols (=$1.6{\times}OC$) and $NO_3{^-}$ concentrations contributed 26.6% and 21.0% to $PM_{2.5}$, respectively. OC and EC concentrations were mainly attributed to traffic emissions with some contribution from biomass burning emissions. Moreover, strong correlations of OC with WSOC, HULIS, and $NO_3{^-}$ suggest that some of the organic aerosols were likely formed through atmospheric oxidation processes of hydrocarbon compounds from traffic emissions. For the period between January 18 and 22 when $PM_{2.5}$ pollution episode occurred, concentrations of three secondary ionic species ($=SO{_4}^{2-}+NO_3{^-}+NH_4{^+}$) and organic matter contributed on average 50.8 and 20.1% of $PM_{2.5}$, respectively, with the highest contribution from $NO_3{^-}$. Synoptic charts, air mass backward trajectories, and local meteorological conditions supported that high $PM_{2.5}$ pollution was resulted from long-range transport of haze particles lingering over northeastern China, accumulation of local emissions, and local production of secondary aerosols. During the $PM_{2.5}$ pollution episode, enhanced $SO{_4}^{2-}$ was more due to the long-range transport of aerosol particles from China rather than local secondary production from $SO_2$. Increasing rate in $NO_3{^-}$ was substantially greater than $NO_2$ and $SO{_4}^{2-}$ increasing rates, suggesting that the increased concentration of $NO_3{^-}$ during the pollution episode was attributed to enhanced formation of local $NO_3{^-}$ through heterogenous reactions of $NO_2$, rather than impact by long-range transportation from China.

• Journal of Korea Port Economic Association
• /
• v.39 no.2
• /
• pp.77-95
• /
• 2023

The regional infrastructure industries of Gwangyang City, the subject of this study, are Gwangyang Port and Gwangyang Steel Mill. Therefore, it is necessary to analyze the regional economic ripple effects of the port logistics industry in Gwangyang City. In this study, a multi-stage approach using the RW and the LQ methodology using the national input-output tables in 2015 and 2019 is used to prepare the regional interindustry analysis chart in Gwangyang City, and an exogenous demand induction model that reclassified the port logistics industry was applied. Through this, the purpose of this study was to provide policy implications by figuring out the regional economic ripple effects of the port logistics industry quantitatively in Gwangyang City. As a result of the analysis, the industries with high production inducement effect and forward/backward linkage effect of the port logistics industry in Gwangyang City were analyzed as manufacturing, transportation, land and air logistics sectors. And the industries in which the added value inducement effect and the employment inducement effect were analyzed as an industry related to the service industry. Therefore, it is necessary to prepare support measures to foster the port logistics industry as a way to promote these industries and revitalize the local economy of Gwangyang City. To this end, it is desirable to improve policies and systems for the vitalization of the Gwangyang port maritime cluster and provide various policy support for the port logistics industry in Gwangyang City. This study is meaningful in suggesting policy implications for the regional economy of Gwangyang City based on the results of exogenous analysis of the port logistics industry in small and medium-sized cities. However, It seems that further studies related to this will be needed in the future.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.4
• /
• pp.567-587
• /
• 2018

A severe haze event occurred in October 2015 in Gwangju, Korea. In this study, the driving chemical species and the formation mechanisms of $PM_{2.5}$ pollution were investigated to better understand the haze event. Hourly concentrations of $PM_{2.5}$, organic and elemental carbon, water-soluble ions, and elemental constituents were measured at the air quality intensive monitoring station in Gwangju. The haze event occurred was attributed to a significant contribution (72.3%) of secondary inorganic species concentration to the $PM_{2.5}$, along with the contribution of organic aerosols that were strongly attributed to traffic emissions over the study site. MODIS images, weather charts, and air mass backward trajectories supported the significant impact of long-range transportation (LTP) of aerosol particles from northeastern China on haze formation over Gwangju in October 2015. The driving factor for the haze formation was stagnant atmospheric flows around the Korean peninsula, and high relative humidity (RH) promoted the haze formation at the site. Under the high RH conditions, $SO{_4}^{2-}$ and $NO_3{^-}$ were mainly produced through the heterogenous aqueous-phase reactions of $SO_2$ and $NO_2$, respectively. Moreover, hourly $O_3$ concentration during the study period was highly elevated, with hourly peaks ranging from 79 to 95ppb, suggesting that photochemical reaction was a possible formation process of secondary aerosols. Over the $PM_{2.5}$ pollution, behavior and formation of secondary ionic species varied with the difference in the impact of LTP. Prior to October 19 when the influence of LTP was low, increasing rate in $NO_3{^-}$ was greater than that in $NO_2$, but both $SO_2$ and $SO{_4}^{2-}$ had similar increasing rates. While, after October 20 when the impact of haze by LTP was significant, $SO{_4}^{2-}$ and $NO_3{^-}$ concentrations increased significantly more than their gaseous precursors, but with greater increasing rate of $NO_3{^-}$. These results suggest the enhanced secondary transformation of $SO_2$ and $NO_2$ during the haze event. Overall, the result from the study suggests that control of anthropogenic combustion sources including vehicle emissions is needed to reduce the high levels of nitrogen oxide and $NO_3{^-}$ and the high $PM_{2.5}$ pollution occurred over fall season in Gwangju.

• Journal of Korean Society for Atmospheric Environment
• /
• v.34 no.1
• /
• pp.16-37
• /
• 2018

In this study, difference in chemical composition of $PM_{2.5}$ observed between the year 2013 and 2015 at six air quality intensive monitoring stations (Bangryenogdo (BR), Seoul (SL), Daejeon (DJ), Gwangju (GJ), Ulsan (US), and Jeju (JJ)) was investigated and the possible factors causing their difference were also discussed. $PM_{2.5}$, organic and elemental carbon (OC and EC), and water-soluble ionic species concentrations were observed on a hourly basis in the six stations. The difference in chemical composition by regions was examined based on emissions of gaseous criteria pollutants (CO, $SO_2$, and $NO_2$), meteorological parameters (wind speed, temperature, and relative humidity), and origins and transport pathways of air masses. For the years 2013 and 2014, annual average $PM_{2.5}$ was in the order of SL ($${\sim_=}DJ$$)>GJ>BR>US>JJ, but the highest concentration in 2015 was found at DJ, following by GJ ($${\sim_=}SJ$$)>BR>US>JJ. Similar patterns were found in $SO{_4}^{2-}$, $NO_3{^-}$, and $NH_4{^+}$. Lower $PM_{2.5}$ at SL than at DJ and GJ was resulted from low concentrations of secondary ionic species. Annual average concentrations of OC and EC by regions had no big difference among the years, but their patterns were distinct from the $PM_{2.5}$, $SO{_4}^{2-}$, $NO_3{^-}$, and $NH_4{^+}$ concentrations by regions. 4-day air mass backward trajectory calculations indicated that in the event of daily average $PM_{2.5}$ exceeding the monthly average values, >70% of the air masses reaching the all stations were coming from northeastern Chinese polluted regions, indicating the long-range transportation (LTP) was an important contributor to $PM_{2.5}$ and its chemical composition at the stations. Lower concentrations of secondary ionic species and $PM_{2.5}$ at SL in 2015 than those at DJ and GJ sites were due to the decrease in impact by LTP from polluted Chinese regions, rather than the difference in local emissions of criteria gas pollutants ($SO_2$, $NO_2$, and $NH_3$) among the SL, DJ, and GJ sites. The difference in annual average $SO{_4}^{2-}$ by regions was resulted from combination of the difference in local $SO_2$ emissions and chemical conversion of $SO_2$ to $SO{_4}^{2-}$, and LTP from China. However, the $SO{_4}^{2-}$ at the sites were more influenced by LTP than the formation by chemical transformation of locally emitted $SO_2$. The $NO_3{^-}$ increase was closely associated with the increase in local emissions of nitrogen oxides at four urban sites except for the BR and JJ, as well as the LTP with a small contribution. Among the meterological parameters (wind speed, temperature, and relative humidity), the ambient temperature was most important factor to control the variation of $PM_{2.5}$ and its major chemical components concentrations. In other words, as the average temperature increases, the $PM_{2.5}$, OC, EC, and $NO_3{^-}$ concentrations showed a decreasing tendency, especially with a prominent feature in $NO_3{^-}$. Results from a case study that examined the $PM_{2.5}$ and its major chemical data observed between February 19 and March 2, 2014 at the all stations suggest that ambient $SO{_4}^{2-}$ and $NO_3{^-}$ concentrations are not necessarily proportional to the concentrations of their precursor emissions because the rates at which they form and their gas/particle partitioning may be controlled by factors (e.g., long range transportation) other than the concentration of the precursor gases.

• Korean Journal of Remote Sensing
• /
• v.30 no.2
• /
• pp.241-249
• /
• 2014

The continuous observations for atmospheric aerosol were carried out during 3 years (2009-2011) by using a multi-wavelength Raman lidar at the Gwangju Institute of Science and Technology (GIST), Korea ($35.11^{\circ}N$, $126.54^{\circ}E$). The particle depolarization ratios were retrieved from the observations in order to distinguish the Asian dust layer. The vertical information of Asian dust layers were used as input parameter for the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model for analysis of its backward trajectories. The source regions and transport pathways of the Asian dust layer were identified. The most frequent source region of Asian dust in Korea was Gobi desert during observation period in this study. The statistical analysis on the particle depolarization ratio of Asian dust was conducted according to their transport route in order to retrieve the variation of optical properties of Asian dust during long-range transport. The transport routes were classified into the Asian dust which was transported to observation site directly from the source regions, and the Asian dust which was passed over pollution regions of China. The particle depolarization ratios of Asian dust which were transported via industrial regions of China was ranged 0.07-0.1, whereas, the particle depolarization ratio of Asian dust which was transported directly from the source regions to observation site were comparably higher and ranged 0.11-0.15. It is considered that the pure Asian dust particle from source regions were mixed with pollution particles, which is likely to spherical particle, during transportation so that the values of particle depolarization of Asian dust mixed with pollution was decreased.

• Journal of the Korean earth science society
• /
• v.41 no.6
• /
• pp.557-574
• /
• 2020

The purpose of this study is to analyze the cause of high PM2.5 mass concentrations in Cheongju for the period of non-Asian dust days using the weather chart, the stream lines at 850 hPa, the backward trajectory, and the weather and air quality model. As a result of analyzing the time series of PM2.5 concentrations and weather charts for the episodic days in Cheongju, the weather patterns were shown in related to long-range transport of PM2.5 from China or surrounding areas. In fact, in the PM2.5 time series, 60-80 ㎍ m-3, which is more than 2-3 times higher than the concentration attributed to Cheongju activities, was observed as a background concentration related to long-range transport. The distribution of high PM2.5 concentration was typically dependent on the locations of the high and low pressures above the ground while the upper jet stream passed through the Korean Peninsula. Consequently, the high PM2.5 concentration in Cheongju is due to massive air pollutants in the form of smog originated from industrial, household and energy combustion sources of Beijing and other nearby regions of China. These air pollutants move along a fast zonal wind caused by the atmospheric pressure arrangement. high concentration of PM2.5 in Cheongju City is because the mass of air pollutants in the form of smog generated from industrial, household and energy combustion origins in Beijing or other nearby regions of China move along a fast wind speed zone according to the atmospheric pressure arrangement of long-distance transportation. Air pollutants including PM2.5 show an M-shaped pattern that passes through the topography of the Cheongju basin from north to south as a belt or band-shaped pollutant. The ground high pressure according to the above-ground high pressure expansion area and cut-off low or low pressure arrangement, or the bands in the form of river stems appear in a gradual incremental pattern that changes into a U-shape under the influence of the wind.