• 한국재료학회지
• /
• 제9권2호
• /
• pp.173-180
• /
• 1999

Thermally evaporated ZnTe films were investigated as a back contact material for CdS/CdTe solar cells. Two deposition methods, coevaporation and double-layer methods, were used for Cu doping in ZnTe films. ZnTe layers (0.2$\mu\textrm{m}$ thick) were deposited either on glass or on CdS/CdTe substrates without intentional heating of the substrates. Post-deposition annealing was performed at 200,300 and $400^{\circ}C$ for 3,6 and 9 minutes, respectively. Band gap of 2.2eV was measured for both undoped and doped films and a slight change in the shape of absorption spectra was observed in Cu-doped samples after annealing at $400^{\circ}C$. The resistivity of as-deposited ZnTe decreased from 10\ulcorner~10\ulcornerΩcm down to 10\ulcornerΩcm as Cu concentration increased from 0 to 14 at.%. There was not a noticeable change in less of annealing temperature up to $300^{\circ}C$ whereas films annealed at $400^{\circ}C$ revealed hexagonal (101) orientations as well. Some of Cu-doped ZnTe revealed x-ray diffraction (XRD) peaks related with Cu\ulcornerTe(x=1.75~2). Grain growth was observed from about 20nm in as-deposited films to 50nm after annealing at $400^{\circ}C$ by scanning electron microscopy (SEM). Cu distribution in ZnTe films was not uniform according to Auger electron spectroscopy (AES) measurements.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.108-111
• /
• 2002

CIGS film has been fabricated on soda-lime glass, which is coated with Mo film. by multi-source evaporation process. The films has been prepared with thickness of 1.0 ${\mu}m$, 1.75${\mu}m$, 2.0${\mu}m$, 2.3${\mu}m$, and 3.0${\mu}m$. X-ray diffraction analysis with film thickness shows that CIGS films exhibit a strong (112) preferred orientation. Furthermore. CIGS films exhibited distinctly decreasing the full width of half-maximum and (112) preferred peak with film thickness. Also, The film's microstructure, such as the preferred orientation, the full width at half-maximum(FWHM), and the interplanar spacing were examined by X-ray diffraction. The preparation condition and the characteristics of the unit layers were as followings ; Mo back contact DC sputter, CIGS absorber layer : three-stage coevaporation, CdS buffer layer : chemical bath deposition, ZnO window layer : RF sputtering, $MgF_2$ antireflectance : E-gun evaporation

• Current Photovoltaic Research
• /
• 제1권2호
• /
• pp.82-89
• /
• 2013

$Cu_2ZnSnS_4$ thin film have been fabricated by rapid thermal annealing of dc-sputtered metal precursor with Cu/ZnSn/Cu stack in sulfur ambient. A CZTS film with a good uniformity was formed at $560^{\circ}C$ in 6 min. $Cu_2SnS_3$ and $Cu_3SnS_4$ secondary phases were present at $540^{\circ}C$ and a trace amount of $Cu_2SnS_3$ secondary phase was present at $560^{\circ}C$. Single-phase large-grained CZTS film with rough surface was formed at $560^{\circ}C$. Solar cell with best efficiency of 4.7% ($V_{oc}=632mV$, $j_{sc}=15.8mA/cm^2$, FF = 47.13%) for an area of $0.44cm^2$ was obtained for the CZTS absorber grown at $560^{\circ}C$ for 6 min. The existence of second phase at lower-temperature annealing and rough surface at higher-temperature annealing caused the degradation of cell performance. Also poor back contact by void formation deteriorated cell performance. The fill factor was below 0.5; it should be increased by minimizing voids at the CZTS/Mo interface. Our results suggest that CZTS absorbers can be grown by rapid thermal annealing of metallic precursors in sulfur ambient for short process times ranging in minutes.

• Pediatric Infection and Vaccine
• /
• 제9권2호
• /
• pp.230-235
• /
• 2002

저자들은 임신 중에 수두를 앓거나 수두 환자와 접촉한 과거력이 없는 산모로부터 출산된 신생아가 생후 7일에 수두를 앓고 난 직후의 아이와 접촉한 후 생후 9개월에 우측 11번 흉곽 신경절을 따라 발생된 대상포진을 임상 및 검사로 확진하였고, acyclovir로 치유한 경험을 하였기에 문헌 고찰과 함께 보고하는 바이다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.389-389
• /
• 2012

Molybdenum is one of the most important materials used as a back ohmic contact for $Cu(In,Ga)(Se,S)_2$ (CIGS) solar cells because it has good electrical properties as an inert and mechanically durable substrate during the absorber film growth. Sputter deposition is the common deposition process for Mo thin films. Molybdenum thin films were deposited on soda lime glass (SLG) substrates using direct-current planar magnetron sputtering technique. The outdiffusion of Na from the SLG through the Mo film to the CIGS based solar cell, also plays an important role in enhancing the device electrical properties and its performance. The structure, surface morphology and electrical characteristics of Mo thin films are generally dependent on deposition parameters such as DC power, pressure, distance between target and substrate, and deposition temperature. The aim of the present study is to show the resistivity of Mo layers, their crystallinity and morphologies, which are influenced by the substrate temperature. The thickness of Mo films is measured by Tencor-P1 profiler. The crystal structures are analyzed using X-ray diffraction (XRD: X'Pert MPD PRO / Philips). The resistivity of Mo thin films was measured by Hall effect measurement system (HMS-3000/0.55T). The surface morphology and grain shape of the films were examined by field emission scanning electron microscopy (FESEM: Hitachi S-4300). The chemical composition of the films was obtained by the energy dispersive X-ray spectroscopy (EDX). Finally the optimum substrate temperature as well as deposition conditions for Mo thin films will be developed.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.323-324
• /
• 2011

현재 많은 blue LED소자의 제작 공정과 소자 표면에 texturing하는 과정이 보고되어 있다. 그 중n층이 위로 올라오는 수직형 LED 구조로 인해 표면 texturing 기술은 빛의 발광 효율을 증가 시킬 수 있는 중요한 기술 중 하나가 되었다. 1 이 연구에서, 우리는 InGaN을 바탕으로 한 LED 소자의 표면 roughening을 건식과 습식 공정을 모두 거치는 과정을 통하여 소자의 발광 효율을 높이는 시도를 하였다. 최근 전도성 물질 기판 위에 증착 되어 있는 수직형 LED 소자 2,3,4는 과거의 사파이어 기판 위에 증착 되어 있는 형태의 LED 소자에 비해 우수한 소자 특성을 보인다. 이는 과거 사파이어 기판을 사용함으로써 낮은 열적 특성과 더불어 전기 정도성에 몇 가지 제약을 초래하게 되었기 때문이다. 반면, 전도성 기판은 LED 구조의 back side ohmic contact을 가능하게 하였고, 더 나은 확산 특성을 보여 주었고 작동 전압 또한 감소 하였다. N층이 위에 있는 수직형 LED 소자는 KrF pulsed excimer laser로 인해 실현 되었다. 이 laser 빛이 투명한 사파이어 기판을 통해 얇은 GaN층에 입사되면, 기판과 GaN가 분리된다. 이 레이저 기술은 laser lift-off(LLO)로 성장된 기판으로부터 LED 구조를 분리하는데 성공하게 하였다. 우리는 건식 식각 공정을 이용하여 n 층이 위에 올라와 있는 구조인 수직형 LED 소자에 roughening을 주고 다시 이 표면에 습식 식각 공정을 적용하여 거친 부분의 거칠기를 또 한번 증가시켰다. 그리고 이 거칠어진 표면은 이 공정이 진행 되기 전의 소자에 비해 빛의 발광 효율이 증가 되었다. 이 두 공정을 포함한 식각 공정은 두 가지 장점이 생겼는데, 한가지는 GaN에서 외부로 방출할 수 있는 표면 지역이 증가되었고, 다른 한가지는 가파른 거칠기 특성으로 인해 critical angle을 증가시킨 것이다.

• Current Photovoltaic Research
• /
• 제3권3호
• /
• pp.85-90
• /
• 2015

Two-step processes for preparing $Cu(In,Ga)Se_2$ absorber layers consist of precursor layer formation and subsequent annealing in a Se-containing atmosphere. Among the various deposition methods for precursor layer, the nonvacuum (wet) processes have been spotlighted as alternatives to vacuum-based methods due to their potential to realize low-cost, scalable PV devices. However, due to its porous nature, the precursor layer deposited on Mo substrate by nonvacuum methods often suffers from thick $MoSe_2$ formation during selenization under a high Se vapor pressure. On the contrary, selenization under a low Se pressure to avoid $MoSe_2$ formation typically leads to low crystal quality of absorber films. Although TiN has been reported as a diffusion barrier against Se, the additional sputtering to deposit TiN layer may induce the complexity of fabrication process and nullify the advantages of nonvacuum deposition of absorber film. In this work, Mo oxide layers via thermal oxidation of Mo substrate have been explored as an alternative diffusion barrier. The morphology and phase evolution was examined as a function of oxidation temperature. The resulting Mo/Mo oxides double layers were employed as a back contact electrode for $CuInSe_2$ solar cells and were found to effectively suppress the formation of $MoSe_2$ layer.

• Current Photovoltaic Research
• /
• 제8권2호
• /
• pp.45-49
• /
• 2020

Molybdenum (Mo) thin films are widely used as back contact in copper indium diselenide (CISe) solar cells. However, despite this, there are only few published studies on the properties of Mo and characteristics of CISe solar cells formed on such Mo substrates. In this studies, we investigated the properties of sputter deposited Mo bilayer, and fabricated non-vacuum CISe solar cells using bilayer Mo substrates. The changes in surface morphology and electrical resistivity were traced by varying the gas pressure during deposition of the bottom Mo layer. In porous surface structure, it was confirmed that the electrical resistivity of Mo bilayer was increased as the amount of oxygen bonded to the Mo atoms increased. The resulting solar cell characteristics vary as the bottom Mo layer deposition pressure, and the maximum solar cell efficiency was achieved when the bottom layer was deposited at 7 mTorr with a thickness of 100 nm and the top layer deposited at 3 mTorr with a thickness of 400 nm.

• Macromolecular Research
• /
• 제17권7호
• /
• pp.458-463
• /
• 2009

Polyurethane (PU) is widely used as a cardiovascular biomaterial due to its good mechanical properties and hemocompatibility, but it is not adhesive to endothelial cells (ECs). Cell adhesive peptides, GRGDS and YIGSR, were found to promote adhesion and spreading of ECs and showed a synergistic effect when both of them were used. In this study, a surface modification was designed to fabricate an EC-active PU surface capable of promoting endothelialization using the peptides and poly(ethylene glycol) (PEG) spacer, The modified PU surfaces were characterized in vitro. The density of the grafted PEG on the PU surface was measured by acid-base back titration to the terminal-free isocyanate groups. The successful immobilization of pep tides was confirmed by amino acid analysis, following hydrolysis, and contact angle measurement. The uniform distribution of peptides on the surface was observed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). To evaluate the EC adhesive property, cell viability test using human umbilical vein EC (HUVEC) was investigated in vitro and enhanced endothelialization was characterized by the introduction of cell adhesive peptides, GRGDS and YIGSR, and PEG spacer. Therefore, GRGDS and YIGSR co-immobilized PU surfaces can be applied to an EC-specific vascular graft with long-term patency by endothelialization.

• 대한영양사협회학술지
• /
• 제12권4호
• /
• pp.404-410
• /
• 2006

This study was done to analyze the contents of food and nutrition information sites on the internet. In analysis, 276 web sites were used. Web sites from 3 internet search engines(Yahoo, Empas, Naver) were selected on the date of July 15th, 2004. The trained panels evaluated web sites' contents by the assessment tools using 3-point scale(2:strongly agree, 1:agree, 0:disagree). The contents classified by topics were functional foods(46.4%), cuisine and cooking(38.4%), food sanitation and safety(30.4%) and so on. Operators of web sites were individual(35.9%), company(30.4%) and public institution(33.7%). About 89.5% of web sites were operated for unspecified people. Contents of the web sites were well established especially in consistency in title and contents(1.6), scientific basis of explanations(1.2) and benefit of information(1.2) and so on while not well established in providing relevant sites(0.7), providing contact address and feed back mechanism(0.7) and so on. Web sites operated by public institutions are rated significantly higher than web sites operated by individual or company. In conclusion, in order to qualitatively improve food and nutrition information on the internet, continuing monitoring and evaluation are highly required and web sites operated by public institutions shall be developed further.