• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.237-237
• /
• 2015

The district of Marlborough has had more than its share of river management projects over the past 150 years, each one uniquely affecting the geomorphology and flood hazard of the Wairau Plains. A major early project was to block the Opawa distributary channel at Conders Bend. The Opawa distributary channel took a third and more of Wairau River floodwaters and was a major increasing threat to Blenheim. The blocking of the Opawa required the Wairau and Lower Wairau rivers to carry greater flood flows more often. Consequently the Lower Wairau River was breaking out of its stopbanks approximately every seven years. The idea of diverting flood waters at Tuamarina by providing a direct diversion to the sea through the beach ridges was conceptualised back around the 1920s however, limits on resources and machinery meant the mission of excavating this diversion didn't become feasible until the 1960s. In 1964 a 10 m wide pilot channel was cut from the sea to Tuamarina with an initial capacity of $700m^3/s$. It was expected that floods would eventually scour this 'Wairau Diversion' to its design channel width of 150 m. This did take many more years than initially thought but after approximately 50 years with a little mechanical assistance the Wairau Diversion reached an adequate capacity. Using the power of the river to erode the channel out to its design width and depth was a brilliant idea that saved many thousands of dollars in construction costs and it is somewhat ironic that it is that very same concept that is now being used to deal with the aggradation problem that the Wairau Diversion has caused. The introduction of the Wairau Diversion did provide some flood relief to the lower reaches of the river but unfortunately as the Diversion channel was eroding and enlarging the Lower Wairau River was aggrading and reducing in capacity due to its inability to pass its sediment load with reduced flood flows. It is estimated that approximately $2,000,000m^3$ of sediment was deposited on the bed of the Lower Wairau River in the time between the Diversion's introduction in 1964 and 2010, raising the Lower Wairau's bed upwards of 1.5m in some locations. A numerical morphological model (MIKE-11 ST) was used to assess a number of options which led to the decision and resource consent to construct an erodible (fuse plug) bank at the head of the Wairau Diversion to divert more frequent scouring-flows ($+400m^3/s$)down the Lower Wairau River. Full control gates were ruled out on the grounds of expense. The initial construction of the erodible bank followed in late 2009 with the bank's level at the fuse location set to overtop and begin washing out at a combined Wairau flow of $1,400m^3/s$ which avoids berm flooding in the Lower Wairau. In the three years since the erodible bank was first constructed the Wairau River has sustained 14 events with recorded flows at Tuamarina above $1,000m^3/s$ and three of events in excess of $2,500m^3/s$. These freshes and floods have resulted in washout and rebuild of the erodible bank eight times with a combined rebuild expenditure of $80,000. Marlborough District Council's Rivers & Drainage Department maintains a regular monitoring program for the bed of the Lower Wairau River, which consists of recurrently surveying a series of standard cross sections and estimating the mean bed level (MBL) at each section as well as an overall MBL change over time. A survey was carried out just prior to the installation of the erodible bank and another survey was carried out earlier this year. The results from this latest survey show for the first time since construction of the Wairau Diversion the Lower Wairau River is enlarging. It is estimated that the entire bed of the Lower Wairau has eroded down by an overall average of 60 mm since the introduction of the erodible bank which equates to a total volume of $260,000m^3$. At a cost of $$0.30/m^3$ this represents excellent value compared to mechanical dredging which would likely be in excess of $$10/m^3$. This confirms that the idea of using the river to enlarge the channel is again working for the Wairau River system and that in time nature's "excavator" will provide a channel capacity that will continue to meet design requirements.

• Anatomy & Biological Anthropology
• /
• v.31 no.4
• /
• pp.133-142
• /
• 2018

3D histology is a imaging system for the 3D structural information of cells or tissues. The synchrotron radiation propagation phase contrast micro-CT has been used in 3D imaging methods. However, the simple phase contrast micro-CT did not give sufficient micro-structural information when the specimen contains soft elements, as is the case with many biomedical tissue samples. The purpose of this study is to develop a new technique to enhance the phase contrast effect for soft tissue imaging. Experiments were performed at the imaging beam lines of Pohang Accelerator Laboratory (PAL). The biomedical tissue samples under frozen state was mounted on a computer-controlled precision stage and rotated in $0.18^{\circ}$ increments through $180^{\circ}$. An X-ray shadow of a specimen was converted into a visual image on the surface of a CdWO4 scintillator that was magnified using a microscopic objective lens(X5 or X20) before being captured with a digital CCD camera. 3-dimensional volume images of the specimen were obtained by applying a filtered back-projection algorithm to the projection images using a software package OCTOPUS. Surface reconstruction and volume segmentation and rendering were performed were performed using Amira software. In this study, We found that synchrotron phase contrast imaging of frozen tissue samples has higher contrast power for soft tissue than that of non-frozen samples. In conclusion, synchrotron radiation propagation phase contrast cryo-microCT imaging offers a promising tool for non-destructive high resolution 3D histology.

• Korean Journal of Heritage: History & Science
• /
• v.50 no.3
• /
• pp.64-87
• /
• 2017

Dahoe is a traditional braid in Joseon Dynasty. There are many Dahoe artifacts, which can give us a glimpse of the costume, culture, and life of that era. The study of Dahoe is necessary in various fields, but it is difficult because this manufacturing technique has been passed down from hand to hand. Few studies have been done so far. This research examines the manufacturing technique of KwangDahoe which is passed down by Maedeupjang (Decorative Knotting) and is generally used for knotting and/or tying objects. The main characteristic of TieKwangDahoe, made through the same method as WonDahoe, is the square hole in the middle. It was impossibile to remake the original braid because there is no confirmed number of the strand. Especially it is very difficult to do conservation and restoration on serious degradation state of the fiber. Therefore, it is necessary to analyze the non-destructive manufacturing techniques method for Dahoe and assess their applicability. First, we analyzed the artifacts' manufacturing technique based on the database of the Dahoe's manufacturing technique. In order to do that, we undertook schematization, restoration, morphological analyzation of the Dahoe. And then, X-ray CT scans were performed to improve the reliability of the DB. These results of scanning were interpreted based on the manufacturing technique. The selected Tie-KwangDahoe on the sword for the study are artifacts including artistic value and symbolism in Joseon Dynasty. Based on the analysis of the manufacturing technique, we found that both artifacts were made of 20-strand braid of single cross according to the length-scale measure. It was manufactured using 8-strand on left-right side, 12-strand on front-back side by the braiding manufacturing technique method Finally, this research suggests non-destructive analysis method of Dahoe's manufacturing technique is based on the database and the analysis results. I hope this research can be useful in various professional fields of Dahoe in the future. Moreover, I hope this can be of any help in preserving Korean cultural heritage.

• Korean Journal of Health Education and Promotion
• /
• v.2 no.1
• /
• pp.31-61
• /
• 2000

Introduction. Despite the fact that half of premature deaths are caused by unhealthy lifestyles such as smoking tobacco, sedentary lifestyle, alcohol and drug abuse and poor nutrition, there are no theoretical models which accurately explain these health promotion related behaviors. This study tests a new model of health behavior called the Model of Health Promotion Behavior. This model draws on elements and frameworks suggested by the Health Belief Model, Social Cognitive Theory, the Theory of Planned Action and the Health Promotion Model. This model is intended as a general model of behavior but this first test of the model uses amount of exercise as the outcome behavior. Design. This study utilized a cross sectional mail-out, mail-back survey design to determine the elements within the model that best explained intentions to exercise and those that best explained amount of exercise. A follow-up questionnaire was mailed to all respondents to the first questionnaire about 10 months after the initial survey. A pretest was conducted to refine the questionnaire and a pilot study to test the protocols and assumptions used to calculate the required sample size. Sample. The sample was drawn from 2000 eligible participants at two blue collar (utility company and part of a hospital) and two white collar (bank and pharmaceutical) companies located in Southeastern Michigan. Both white collar site had employee fitness centers and all four sites offered health promotion programs. In the first survey, 982 responses were received (49.1％) after two mailings to non-respondents and one additional mailing to secure answers to missing data, with 845 usable cases for the analyzing current intentions and 918 usable cases for the explaining of amount of current exercise analysis. In the follow-up survey, questionnaires were mailed to the 982 employees who responded to the initial survey. After one follow-up mailing to non-respondents, and one mailing to secure answers to missing data, 697 (71.0％) responses were received, with 627 (63.8％) usable cases to predict intentions and 673 (68.5％) usable cases to predict amount of exercise. Measures. The questionnaire in the initial survey had 15 scales and 134 items; these scales measured each of the variables in the model. Thirteen of the scales were drawn from the literature, all had Cronbach's alpha scores above .74 and all but three had scores above .80. The questionnaire in the second mailing had only 10 items, and measured only outcome variables. Analysis. The analysis included calculation of scale scores, Cronbach's alpha, zero order correlations, and factor analysis, ordinary least square analysis, hierarchical tests of interaction terms and path analysis, and comparisons of results based on a random split of the data and splits based on gender and employer site. The power of the regression analysis was .99 at the .01 significance level for the model as a whole. Results. Self efficacy and Non-Health Benefits emerged as the most powerful predictors of Intentions to exercise, together explaining approximately 19％ of the variance in future Intentions. Intentions, and the interaction of Intentions with Barriers, with Support of Friends, and with Self Efficacy were the most consistent predictors of amount of future exercise, together explaining 38％ of the variance. With the inclusion of Prior Exercise History the model explained 52％ of the variance in amount of exercise 10 months later. There were very few differences in the variables that emerged as important predictors of intentions or exercise in the different employer sites or between males and females. Discussion. This new model is viable in predicting intentions to exercise and amount of exercise, both in absolute terms and when compared to existing models.

• Journal of Distribution Research
• /
• v.16 no.1
• /
• pp.141-177
• /
• 2011

I. Research Objectives: Most of the previous studies on diffusion have concentrated on efficacy of WOM communication with the use of variables at individual level (Iacobucci 1996; Midgley et al. 1992). However, there is a paucity of studies which investigated network's structural properties as antecedents of WOM from the perspective of consumers' sociocultural propensities. Against this research backbone, this study attempted to link the network's structural properties and consumer' WOM behavior on cross-national basis. The major research objective of this study was to examine the relationship between network properties and WOM by comparing Korean and Chinese consumers. Specific objectives of this research are threefold; firstly, it sought to examine whether network properties (i.e., tie strength, centrality, range) affect WOM (WOM intention and quality of WOM). Secondly, it aimed to explore the moderating effects of cutural orientation (uncertainty avoidance and individuality) on the relationship between network properties and WOM. Thirdly, it substantiates the role of innovativeness as antecedents to both network properties and WOM. II. Research Hypotheses: Based on the above research objectives, the study put forth the following research hypotheses to validate. ${\cdot}$ H 1-1 : The Strength of tie between two counterparts within network will positively influence WOM effectivenes ${\cdot}$ H 1-2 : The network centrality will positively influence the WOM effectiveness ${\cdot}$ H 1-3 : The network range will positively influence the WOM effectiveness ${\cdot}$ H 2-1 : The consumer's uncertainty avoidance tendency will moderate the relationship between network properties and WOM effectiveness ${\cdot}$ H 2-2 : The consumer's individualism tendency will moderate the relationship between network properties and WOM effectiveness ${\cdot}$ H 3-1 : The consumer's innovativeness will positively influence the social network properties ${\cdot}$ H 3-2 : The consumer's innovativeness will positively influence WOM effectiveness III. Methodology: Through a pilot study and back-translation, two versions of questionnaire were prepared, one in Korean and the other in Chinese. The chinese data were collected from the chinese students enrolled in language schools in Suwon city in Korea, while Korean data were collected from students taking classes in a major university in Seoul. A total of 277 questionnaire were used for analysis of Korean data and 212 for Chinese data. The reason why Chinese students living in Korea rather than in China were selected was based on two factors: one was to neutralize the differences (ie, retail channel availability) that may arise from living in separate countries and the second was to minimize the difference in communication venues such as internet accessibility and cell phone usability. SPSS 12.0 and AMOS 7.0 were used for analysis. IV. Results: Prior to hypothesis verification, mean differences between the two countries in terms of major constructs were performed with the following result; As for network properties (tie strength, centrality and range), Koreans showed higher scores in all three constructs. For cultural orientation traits, Koreans scored higher only on uncertainty avoidance trait than Chinese. As a result of verifying the first research objective, confirming the relationship between network properties and WOM effectiveness, on Korean side, tie strength(Beta=.116; t=1.785) and centrality (Beta=.499; t=6.776) significantly influenced on WOM intention, and similar finding was obtained for Chinese side, with tie strength (Beta=.246; t=3.544) and centrality (Beta=.247; t=3.538) being significant. However, with regard to WOM argument quality, Korean data yielded only centrality (Beta=.82; t=7.600) having a significant impact on WOM, whereas China showed both tie strength(Beat=.142; t=2.052) and centrality(Beta=.348; t=5.031) being influential. To answer for the second research objective addressing the moderating role of cultural orientation, moderated regression anaylsis was performed and the result showed that uncertainty avoidance moderated between network range and WOM intention for both Korea and China, But for Korea, the uncertainty avoidance moderated between tie strength and WOM quality, while for China it moderated between network range and WOM intention. And innovativeness moderated between tie strength and WOM intention for Korea but it moderated between network range and WOM intention for China. As a result of analysing for third research objective, we found that for Korea, innovativeness positively influenced centrality only (Beta=.546; t=10.808), while for China it influenced both tie strength (Beta=.203; t=2.998) and centrality(Beta=.518; t=8.782). But for both countries alike, the innovativeness influenced positively on WOM (WOM intention and WOM quality). V. Implications: The study yields the two practical implications. Firstly, the result suggests that companies targeting multinational customers need to identify segments which are susceptible to the positive WOM and WOM information based on individual traits such as uncertainty avoidance and individualism and based on that, develop marketing communication strategy. Secondly, the companies need to divide the market on Roger's five innovation stages and based on this information, enforce marketing strategy which utilizes social networking tools such as public media and WOM. For instance, innovator and early adopters, if provided with new product information, will be able to capitalize upon the network advantages and thus add informational value to network operations using SNS or corporate blog.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.2 no.1
• /
• pp.65-73
• /
• 1999

Purpose: Regurgitation, vomiting and feeding intolerance are frequent in the neonates. Esophageal function and gastric peristalsis are not fully developed in the neonates, so we should give attention to reduce the incidence of regurgitation and vomiting after feeding. It is necessary to shorten the gastric emptying by change of feeding types and postprandial postures. Gastric emptying time was measured by ultrasound in the neonates to evaluate the effect of feeding types and postprandial postures. Method: We measured gastric antral cross sectional area along the abdominal aorta at the level of the superior mesenteric artery in longitudinal section at NPO state (4 hours after feeding), 0 and every 30 min. after feeding until the value goes below or back to the NPO state. Fifteen neonates were examined in each breast-fed and formula-fed group in supine position. Eighteen and 15 neonates were examined in supine and prone posture after formula feeding, respectively. We used 5 MHz convex prove with Aloka Echo Camera SSD-650. Result: 1) Gastric emptying time of breast-fed infants was $76.0{\pm}20.02$ min. which was significantly shorter than $96.0{\pm}20.28$ min. of formula-fed infants. 2) Gastric emptying time on postprandial prone posture was $85.0{\pm}22.43$ min. which was not significantly different from $96.0{\pm}20.28$ min. on postprandial supine posture. Conclusion: Breast feeding is strongly recommended to the neonates to shorten gastric emptying time. So we can expect to reduce the incidence of regurgitation, vomiting and feeding intolerance. The postprandial posture depends on the traditional trend which is safe and comfortable to the mothers.

• Journal of Preventive Medicine and Public Health
• /
• v.29 no.4 s.55
• /
• pp.785-799
• /
• 1996

We investigated the 1,004 workers who worked in a automobile factory to study the epidemiologic characterists of dermatoses due to cutting oils. Among the workers, 667(66.4%) answered the questionaire. They are belong to 5 departments of the factory-the Engine-Work(258 workers), Gasoline engine Assembly(210), Diesel engine Assembly(96), Power train Work(86), Power train Assembly(17). We measured the oil mist concentration in air of the departments and examined the workers who had dermatologic symptoms. The results were follows; 1) Oil mist concentration ; Of all measured points(52),9 points(17.2%) exeeded $5mg/m^3$- the time-weighed PEL-and one department had a upper confidence limit(95%) higher than $5mg/m^3$. 2) Dermatologists examined 213 workers. 172 of them complained any skin symptoms at that time - itching(32.5%), papule(21.6%), scale(15.7%), vesicle(12.5%) in order. The abnormal skin site found by dermatologist were palm(29.3%), finger & nail(24.6%), forearm(16.2%), back of hand(8.4%) in order. 3) As the result of physical examination, we found that 160 workers had skin diseases. Contact dermatitis was the most common; 69 workers had contact dermatitis alone(43.1%), 11 had contact dermatitis with acne(6.9%), 10 had contact dermatitis with folliculitis(6.3%), 1 had contact dermatitis with acne & folliculitis, and 1 had contact dermatitis with abnormal pigmentation. Others were folliculitis(9 workers, 5.6%), acne(8, 5.0%), folliculitis & acne (2, 1.2%), keratosis(1, 0.6%), abnormal pigmentation (1, 0.6%), and non-specific hand eczema (47, 29.3%). 4) The prevalence of any skin diseases was 34.0 pet 100 in cutting oil users, and 13.3 per 100 in non- users. Especially, the prevalence of contact dermatitis was 23.0 per 100 in cutting oil users and 23.0 per 100 in non-users. 5) We tried patch test(standard serise, oil serise, organic solvents) on 49 patients to differentiate allergic contact dermatitis from irritant contact dermatitis and found 20 were positive. 6) In a multivariate analysis(independant=age, tenure, kinds of cutting oil), the risk of skin diseases was higher in the water-based cutting oil user and both oil user than non-user or neat oil user(odds ratio were 2.16 and 2.78, respectively). And the risk of contact dermatitis was much higher at the same groups(odds ratio were 5.16 and 6.82, respectively).

• Korean Journal of Agricultural Science
• /
• v.10 no.2
• /
• pp.221-234
• /
• 1983

A study was conducted to devise a method to estimate the edible meat weight in live broilers. White Cornish broiler chicks CC, Single Comb White Leghorn egg strain chicks LL, and two reciprocal cross breeds of these two parent stocks (CL and LC) were employed A total of 240 birds, 60 birds from each breed, were reared and sacrificed at 0, 2, 4, 6, 8 and 10 weeks of ages in order to measure various body parameters. Results obtained from this study were summarized as follows. 1) The average body weight of CC and LL were 1,820g and 668g, respectively, at 8 weeks of age. The feed to gain ratios for CC and LL were 2.24 and 3.28, respectively. 2) The weight percentages of edible meat to body weight were 34.7, 36.8 and 37.5% at 6, 8 and 10 weeks of ages, respectively, for CC. The values for LL were 30.7, 30.5 and 32.3%, respectively, The CL and LC were intermediate in this respect. No significant differences were found among four breeds employed. 3) The CC showed significantly smaller weight percentages than did the other breeds in neck, feather, and inedible viscera. In comparison, the LL showed the smaller weight percentages of leg and abdominal fat to body weight than did the others. No significant difference was found among breeds in terms of the weight percentages of blood to body weight. With regard to edible meat, the CC showed significantly heavier breast and drumstick, and the edible viscera was significantly heavier in LL. There was no consistent trend in neck, wing and back weights. 4) The CC showed significantly larger measurements body shape components than did the other breeds at all time. Moreover, significant difference was found in body shape measurements between CL and LC at 10 weeks of age. 5) All of the measurements of body shape components except breast angle were highly correlated with edible meat weight. Therefore, it appeared to be possible to estimate the edible meat wight of live chickens by the use of these values. 6) The optimum regression equations for the estimation of edible meat weight by body shape measurements at 10 weeks of age were as follows. $$Y_{cc}=-1,475.581 +5.054X_{26}+3.080X_{24}+3.772X_{25}+14.321X_{35}+1.922X_{27}(R^2=0.88)$$ $$Y_{LL}=-347.407+4.549X_{33}+3.003X_{31}(R^2=0.89)$$ $$Y_{CL}=-1,616.793+4.430X_{24}+8.566X_{32}(R^2=0.73)$$ $$Y_{LC}=-603.938+2.142X_{24}+3.039X_{27}+3.289X_{33}(R^2=0.96)$$ Where $X_{24}$=chest girth, $X_{25}$=breast width, $X_{26}$=breast length, $X_{27}$=keel length, $X_{31}$=drumstick girth, $X_{32}$=tibotarsus length, $X_{33}$=shank length, and $X_{35}$=shank diameter. 7) The breed and age factors caused considerable variations in assessing the edible meat weight in live chicken. It seems however that the edible meat weight in live chicken can be estimated fairly accurately with optimum regression equations derived from various body shape measurements.