• Journal of Mechanical Science and Technology
• /
• 제14권3호
• /
• pp.314-319
• /
• 2000

Back-face strain compliance (BFS compliance) for the four-point bend specimen has been calibrated for various crack length ratios. Finite element technique was employed to simulate four-point loading and calculate back-face strain of the bend specimen. The numerically determined strain variation along the back face indicates that the sensitivity to gage placement increases with crack length and back-face strain at the gage length less than O.2W, where W is the width of the bend specimen, can be measured within 5% deviation of the maximum BFS. Non-dimensional back-face strain compliance, -E'BCW, was calibrated with FE analysis and experiment. The experimentally determined compliance indicates good agreement with the numerical compliance and can be expressed as a function of crack length ratio.

• 한국산학기술학회논문지
• /
• 제17권12호
• /
• pp.686-691
• /
• 2016

용접강구조물에서는 용접비드와 같은 응력집중부가 많이 존재한다. 또한 용접부에서는 용접결함이 발생할 가능성이 많다. 반복적인 피로하중이 응력집중부에 작용하면 응력집중부에서 피로균열이 발생하고, 발생된 균열의 전파에 의해 피로파괴사고를 일으킨다. 따라서 피로파괴사고를 미연에 방지하기 위하여 균열발생수명과 균열전파수명과 같은 피로수명의 파악이 필요하다. 본 연구에서는 피로균열전파특성 연구에 사용되는 컴플라이언스를 도출하였다. 이 컴플라이언스는 피로균열의 자동화 측정에 활용할 수 있다. 본 연구에서는 CT시험편에 대하여 in-house FEM program을 사용하여 컴플라이언스를 계산하였다. 이 계산결과는 저자의 앞선 연구에서 본 프로그램을 사용하여 계산한 J integral의 계산결과와 대비하여 a/W와의 관계를 제시하였다. 그리고 또한 CT시험편 Back Face의 중앙부로부터 위아래 방향의 스트레인 분포에 계산을 실시하였다. 이 분포에서는 중심으로부터 위아래로 갈수록 스트레인이 감소하는 경향을 나타내었다. 이상의 계산과정으로부터 균열진전시험의 자동수행을 위한 컴플라이언스를 얻을 수 있었다. 이것으로부터 CT 시험편의 피로균열진전시험의 자동화에 활용이 가능하게 되었다.

• Steel and Composite Structures
• /
• 제29권1호
• /
• pp.23-37
• /
• 2018

In this paper, seismic provisions related to built-up special concentrically braced frames (BSCBFs) are investigated under cyclic loading using non-linear finite element analysis of a single-bay single-story frame. These braces, which contain double angle and double channel brace sections, are considered in two types of single diagonal and X-braced frames. The results of this study show that current seismic provisions such as observing the 0.4 ratio for slenderness ratio of individual elements between stitch connectors are conservative in BSCBFs, and can be increased according to the type of braces. Furthermore, such increments will lead to decreasing or remaining the current middle protected zone requirements of each BSCBFs. Failure results of BSCBFs, which are related to the plastic equivalent strain growth of members and ductility capacity of the models, show that the behaviors of double channel back-to-back diagonal braces are more desirable than those of similar face-to-face ones. Also, for double angle diagonal braces, results show that the failure of back-to-back BSCBFs occurs faster in comparison with face-to-face similar braces. In X-braced frames, cyclic and failure behaviors of built-up face-to-face models are more desirable than similar back-to-back braces in general.

• 대한기계학회논문집
• /
• 제17권9호
• /
• pp.2145-2152
• /
• 1993

The objective of this paper is to examine the detection limit, growth characteristics and notch curvature radius in short crack problem. Measurement techniques such as ultrasonic method and back-face strain compliance method were adopted. The fatigue crack growth rate of the short crack is slower than that of a long crack for a notched specimen. The characteristic of crack growth and crack closure is same as the case of a delay of crack growth caused by constant amplitude load for an ideal crack or single peak overload for a fatigue crack. The short crack is detected effectively by ultrasonic method. A short surface crack occurs in the middle of specimen thickness and is transient to a through crack depth is larger than the notch curvature radius.

• 대한기계학회논문집
• /
• 제14권1호
• /
• pp.96-102
• /
• 1990

본 연구에서는 압력용기 소재인 SPV 50Q와 고압강관 소재로 사용하는 SPV 50Q 와 고압강간 소재로 사용하는 API 5A-K55에서의 표면균열의 표면방향과 깊이방향 또한 두께 평균에 대한 균열열림을 스트레인 게이지와 CMOD(Crack Mouth Opening Displace- ment)게이지를 이용하여 측정 비교하였다. 또한 표면균열의 균열 열림하중을 측정위 치에 따라 평가하고, 본연구에 사용한 두 소재에 대해 균열 열림을 고려한 표면균열 진전평가가 각 방향에 대해 이루어졌다.

• 소성∙가공
• /
• 제29권3호
• /
• pp.163-171
• /
• 2020

We present a multi-step cold drawing for a non-equiatomic Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ high entropy alloy (HEA) with a simple face-centered cubic (FCC) crystal structure. The distribution of strain in the cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wires was analyzed by the finite element method (FEM). The effective strain was expected to be higher as it was closer to the surface of the wire. However, the reverse shear strain acted to cause a transition in the shear strain behavior. The critical effective strain at which the shear strain transition behavior is completely shifted was predicted to be 4.75. Severely cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wires up to 96% of the maximum cross-sectional reduction ratio were successfully manufactured without breakage. With the assistance of electron back-scattering diffraction and transmission electron microscope analyses, the abundant deformation twins were found in the region of high effective strain, which is a major strengthening mechanism for the cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wire.

• 한국자동차공학회논문집
• /
• 제20권4호
• /
• pp.33-38
• /
• 2012

Sandwich composite panel with high strength steel face can reduce the weight of the automotive structural parts. Unlike the parts in aerospace application, the automotive parts are made by the forming process for mass production. The CAE simulation can predict the failures caused by forces and deformation during the forming process. Since the material properties are very important factor for the simulation, we performed the tensile test to get the material properties. The inspections by the optical microscope at each strain level show the states of the polymer resin. The material properties measured by the tensile tests are used for the input data of simulation. The simulation predicts the forming process of the bumper back beam very exactly compared with the try out results.

• 한국산업융합학회 논문집
• /
• 제10권1호
• /
• pp.39-46
• /
• 2007

The objective of this paper is to examine the detection limit, growth characteristics and notch curvature radius in short crack problem. Measurement techniques such as ultrasonic method and back-face strain compliance method were adapted. The fatigue crack growth rate of the short crack is slower than that of a long crack for a notched specimen. The short crack is detected effectively by ultrasonic method. A short surface crack occurs in the middle of specimen thickness and is transient to a through crack when maximum crack depth is larger than the notch curvature radius.

• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.300-307
• /
• 2002

Partial penetration welding joint is defined as groove welds welded from one side, without steel backing or groove welds welded from both sides but without back gouging. So it has an unwelded portion at the root of the weld. Study of partial penetration weldment fracture behavior includes residual stress analysis and fracture analysis. The J-integral loses its path independency in residual stress field. Therefore, it is necessary to introduce a new J-integral, J, which is defined including the effect of plastic deformation and thermal strain. In this study, theoretical formulation and program were developed for the evaluation of J-integral for the crack tip located in the weldment. Evaluations of fracture behavior were performed for partial penetration multi-pass weldment of 25.4mm thick plate by J-integral. From a point of fracture in partial penetration multi-pass welding, it seemed to be better to control root face smaller than 6.35mm.

• 대한한방내과학회지
• /
• 제15권1호
• /
• pp.176-209
• /
• 1994

1. The Jung-Sa(正邪) of the Excessive Liver-Symptoms belongs to the eleven symptoms, there are blue face, blue thin fingernail, anger, fancy of larg body, dizziness, eye flame, Bell's palsy, hard swelling pain at braest, side pain going on the belly from the side, side pain and movement at the left side. 2. The Mi-Sa(微邪) of the Excessive Liver-Symptoms belongs to the four symptoms, there are meat in eye, edema in cheek, lack of appetite and diarrhea. 3. The Juk-Sa(賊邪) of the Excessive Liver-Symptoms belongs to the only one symptom, this is nosebleeding. 4. The Hu-Sa(虛邪) of the Excessive Liver-Symptoms belongs to the three symptoms, there are scrotum constraction, strain in belly and constipation. 5. The Sil-Sa(實邪) of the Excessive Liver-Symptoms belongs to the twenty eight symptoms, there are red eye, raised eyes(兩眼上?), spitting blood, sternocostal turgid pain, turgidity in belly, drooping testis, vomiting water acid, sickening, belching, confusion, impatience, frequent forgetfulness, headache, giddness, eye pain, deaf, ringing in the ear, feeling inverse, drying mouth, stuffiness sensation in the chest, chest pain, stuffiness sensation in the belly, bellyache, quadriplegia, spasm of extremities, tremor, alternate spells of fever and chills, high fever and strain in muscle. 6. Those symptoms, Red corner of the eye, red face, swelling on the forehead, stiff-neck and back strong, opisthotonos, constracture of the limbs, vomiting yellow bitter water, speech impediment, epilepsy, depression, strong tongue, different thing in throat, fullness and distention of the gastric region, feeling sick and tenesmus, have no connected with the Excessive Liver-Symptoms(肝實證) 7. The Excessive Liver-Symptoms(肝實證) is connected with the ganjabyoung(肝自病) and Hwa(火) which the pathology is, than because Mock(木) is excessive and Mock-Saeng-Hwa(木生火), the ganjabyoung(肝自病) and Sil-Sa(實邪) are many. 8. There are the sixteen symptoms with the exception of The Excessive Liver-Symptoms(肝實證), because supposed that the scholars in medicine included the union syndroms(合病), the combine syndroms(兼病) and the analysis of symptoms(辨證) in The Analysis of Five Visceral Symptoms. 9. During consideration of the symptoms at the above statements, where are many causes by Gan-Pung(肝風), there is difficult of distinction between the excessive Liver-Symptoms(肝實證) and C.V.A(Cerebral Vascular Attack). Because than NaeKyung(內經) distinguished between the excessive Liver-Symptoms(肝實證) and C.V.A., the future medical specialists connected with the excessive Liver-Symptoms(肝實證) and C.V.A.. 10. An appearance of Sang-Hwa(相火) that the liver possessed is divided into an appearance of Hwa(火), there will be making a study att the more necessary. 11. The cuases of each syndroms are consist of the origins of syndroms, its pathology and the positions where the syndroms appeared, I consider that is the various ways how judge the syndroms except the Five Pathogenic Factors(五邪). 12. If more than study will be achieved in all, the new definition will be standed about the Excessive and Deficient Five Visceral Syndroms(五臟虛實證), I consider this will be the foundation data that study the Oriental Medicine and the important data that is a judgement standard of clininc.