• 전력전자학회논문지
• /
• 제18권6호
• /
• pp.573-578
• /
• 2013

In the case of the Back EMF voltage contains the harmonics, the motor torque ripple and vibration is occurred by the current pulsation, because IPMSM control algorithm is the model which is assumed that it contains a sinusoidal Back EMF voltage. To improve ride quality, in the case of IPMSM for EV, improving the torque control characteristics is necessary. Therefore, there is a need to minimize the influence of the harmonics. In this paper, the investigation to decrease the current distortion factor has been performed for improving torque control characteristics by applying the non-sinusoidal Back EMF to IPMSM model.

• Journal of Electrical Engineering and Technology
• /
• 제11권3호
• /
• pp.715-723
• /
• 2016

This paper proposes a design of optimal PI(D) controller for brushless DC (BLDC) motor speed control by the particle swarm optimization (PSO), one of the powerful metaheuristic optimization search techniques. The proposed control system is implemented on the TMS320F28335 DSP board interfacing to MATLAB/SIMULINK. With Back EMF detection, the proposed system is considered as a class of sensorless control. This scheme leads to the speed adjustment of the BLDC motor by PWM. In this work, the BLDC motor of 100 watt is conducted to investigate the control performance. As results, it was found that the speed response of BLDC motor can be regulated at the operating speed of 800 and 1200 rpm in both no load and full load conditions. Very satisfactory responses of the BLDC system can be successfully achieved by the proposed control structure and PSO-based design approach.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.447-450
• /
• 2002

A study on control of BLDC Is studying In progress, because of radical increase of survo motor at industrial machine and home machine. Nowaday, we study on control of BLDC, because of radical increase of survo motor at Industry and home. Although control ratio and output of the unit volume are good than the others , BLDC motor demands high cost. Therefor, the study on low cost BLDC have square wave back-emf is studing in progress. Therefor, BLDC Motor was studied to reduce high cost that have square wave back-emf at recently. This paper shows that BLDC Motor, developed highly responsility by using Genetic Algorithm(GA) that the advantages of learning ability, Also, this paper shows experiment and simulation at 200W BLDC that have squarewave back-emf by using Genetic Algorithm. At the result of this methods, the study prove experiment's right.

• Journal of Power Electronics
• /
• 제17권5호
• /
• pp.1223-1230
• /
• 2017

The back emf harmonics of a permanent magnet (PM) synchronous motor is a major source of torque ripple. For torque control applications including column fitted MDPS (motor driven power steering) systems, it is essential to reduce the mechanical vibrations due to torque ripples at low speeds. In this paper, a torque ripple reduction algorithm for interior PM synchronous motors is proposed. The harmonic currents that cancel the $6^{th}$ order torque harmonic are added to the nominal dq currents for MTPA (maximum torque per ampere) operation. The compensated harmonic currents are derived from flux linkage harmonics based on a FFT analysis of the back emf harmonics. Simulation and experimental results verify that the $6^{th}$ order torque harmonic and THD of the torque ripple are reduced by compensating the dq harmonic currents.

• 전력전자학회논문지
• /
• 제20권5호
• /
• pp.429-436
• /
• 2015

Torque ripples generate mechanical vibration at low speed and acoustic noise at high speed. The back emf harmonics of a PM synchronous motor is one of the main sources of torque ripples. To reduce torque ripples resulting from back emf harmonics, dq-axis harmonic currents that reduce the torque ripples are generally compensated to the current controller. Harmonic current compensation is effective at low speed, but it is not applicable at high speed because of the limited bandwidth of the current controller. In this study, dq-axis harmonic voltage compensation that can reduce torque ripples at high speed is proposed. The dq-axis harmonic voltages are calculated from the motor speed and the dq-axis harmonic currents. The effectiveness of the proposed method in reducing torque ripple is verified by a simulation and experiments.

• Journal of Magnetics
• /
• 제21권2호
• /
• pp.173-178
• /
• 2016

Six-step commutation control widely used in brushless DC (BLDC) motor can be applied to consequent pole permanent magnet (CPPM) belt starter generator (BSG) with trapezoidal back electromotive force (EMF) in the starter state. However, rotor position detection with three Hall sensors in BLDC motor can hardly be employed in CPPM BSG due to asymmetric flux distribution in each pole side of CPPM BSG. This paper presents a low-cost rotor position detection method for CPPM BSG in which six Hall sensors are proposed to be used based on the analysis of flux distribution by 3D FEA. In the method, the six Hall sensors are divided into three groups and two signals in each group are combined through performing logic operations. In addition, offset angle between back EMF and the related Hall signal can be compensated by moving the Hall sensors. Experiments of a 2 kW CPPM BSG prototype have also been performed to verify the proposed method.

• 반도체디스플레이기술학회지
• /
• 제20권4호
• /
• pp.38-43
• /
• 2021

Permanent magnet linear synchronous motor (PMLSM) is suitable for use in cleanroom environments and have advantages such as high speed, high thrust, and high precision. If the stators are arranged in the entire moving path of the mover, there is a problem in that the installation cost increases. To solve this problem, discontinuous armature arrangement PMLSM has been proposed. In this case, the mover receives a greater detent force in the section where the stator is not arranged. When a large detent force occurs, it appears as a ripple component of the thrust during PMLSM operation. If the shape of the stator is changed to reduce the detent force, the characteristics of the back EMF are changed. Therefore, in this paper, the detent force and the harmonic components of back EMF were reduced through multi-purpose shape optimization. To this end, the FEA model was constructed and main effect analysis was performed on the major shape variables affecting each objective function. Then, the optimal shape that minimizes the objective function was derived through the response surface analysis method.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권6호
• /
• pp.380-386
• /
• 2000

This paper presents the mathematical modelling analysis of Brushless Synchronous Motor(BLSM). The dynamic and the steady state characteristics of BLSM are simulated and analyzed : electromagnetic torque, speed, line voltage, and current. We used mathematical modelling to model of BLSM with sinusoidal back EMF, namely the shaft transformation referencing rotor frame from a, b, c three to produce constant torque like synchronous motor. The experiment result has already similar to compare with simulation result : torque error about 7%, speed error about 5%. The validity of proposed modelling and analysis was confirmed by the experimental result.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.656-659
• /
• 2000

Recently, the skeleton type 2-phase brushless DC motor has been used in electric home appliance for low price and low energy consumption. In this paper, we analyzed a skeleton type 2-phase BLDC motor using time-step finite element method. And the validity of analysis is confirmed by measuring the flux distribution on the surface of permanent magnet and back-EMF. As well, we have calculated the dynamic characteristics of target motor considering the Hall sensor position. So, we have found the optimum switching position, and improved efficiency of 2-phase BLDC motor.

• Journal of Electrical Engineering and Technology
• /
• 제1권1호
• /
• pp.52-57
• /
• 2006

In this paper, a new 'impedance sensing' method is described. This method overcomes the shortcomings of the impedance sensing method. According to the new method, sensing voltage pulse is applied to the idle phase in the minimum inductance region and the beginning of the increasing inductance region to detect rotor position. The negative torque produced by the sensing voltage pulse can be neglected in the minimum inductance region and the efficiency of SRM is improved. In the minimum inductance region the back electromotive force (EMF) can be neglected. And in the increasing inductance region the EMF opposes the rise of current in the phase, so the position estimation scheme is reliable. Therefore the new 'impedance sensing' method is sufficiently precise even under the high back EMF effect. The adjustment of turn-on angle and turn-off angle is also easy to be realized. The technique is very useful in applications where cost or size is primary concerns, such as electric bicycle drives. Experimental results are presented to verify the proposed method.