• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.219-222
• /
• 2007

The Full-Off Fitting of Movable Bracket using conventional line have received a dynamic contact impact between contact wire and pantograph of electric rolling stock, so this impact cause a rapid vibration of foreword and back near the supporting point of movable bracket. The Full-Off Fitting on Movable Bracket in conventional line differs from that in high speed line. Now conventional line have required a speed up for new electric locomotive and electric car. In speed-up track and big impact place, the Full-Off Fitting and the dropper often get demage. We have done a study of buffering function to solve that problem in conventional line. We have find a need adopting buffer fitting. It is decrease a dynamic impact between contact wire and pantograph of electric rolling stock.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.3
• /
• pp.115-121
• /
• 2001

In micro automation technology, the concurrent realization of a high resolution and a large operating rage has been achieved by a dual actuator, usually called by piggy-back system, conventionally. But, because of its manufacturing cost, the complexity of control, and the limit of overall bandwidth, the contract-free and single servo actuators have been suggested with specific applications. In this paper, we suggest a novel non-contact surface actuator suing combination of the Lorentz force and the magnetized force, and discuss the actuating principles including an analytical approach. Differently from the existing planar system, an operating range of the suggested system can be expanded by an additional attachment of active elements. Therefore, it is estimated to be suitable for the next-generation moving system.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.889-894
• /
• 2001

A three dimensional transient thermo-elastic frictional contact analysis of airplane brakes is performed. The velocity history of the airplane during braking is calculated from energy conservation law. ABAQUS code is used in the analysis, and user subroutines supported in the ABAQUS are coded to calculate the frictional heat generation between pads and linings attached to back/pressure plate and rotor, respectively. Numerical results are compared with experimental ones.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.127-128
• /
• 2006

일반적으로 screen printing 전극은 양산용 태양전지에 많이 응용되고 있다. 이것은 공정이 진공상태 내에서 이루어지지 않으므로 비교적 간단하게 증착 가능하고, co-firing으로 인한 공정단계의 함축과, 기판의 화학적인 오염이 적으며, 시료를 용도에 따라 다양하게 선택적으로 사용할 수 있고, 많은 수량의 태양전지에 전극을 저비용으로 빠르게 형성할 수 있기에 throughput 이 높은 장점이 있다. 하지만 lithography에 의한 전극보다 저항이 높고, uniformity가 낮은 단점이 있다. 본 연구에서는 Ag 전면전극과 Al 후면전극을 형성하고 conventional furnace에서 co-firing하여 열처리조건에 따라서 전극이 최적화된 가장 낮은 저항을 갖도록 하여 단점을 개선하여 보았다.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.269-279
• /
• 2000

This paper deals with the development of biomechanical model on a seat with backrest support in the vertical direction. Four kinds of biomechanical models are discussed to depict human motion. One DOF model mainly describes z-axis motion of hip, two and three DOF models describe z-axis of hip and head, and while nine DOF model suggested in this study represents more motion than the otehr model. Three kinds of experiments were executed to validate these models. The first one was to measure the acceleration of the floor and hip surface in z-axis, the back surface in x-axis, and the head in z-axis under exciter. From this measurement, the transmissiblities of each subject were obtained. The second one was the measurement of the joint position by the device having pointer and the measurement of contact position between the human body and the seat by body pressure distribution. The third one was the measurement of the seat and back cushion by dummy. The biomechanical model parameters were obtained by matching the simulated to the experimental transmissiblities at the hip, back, and head.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.245-245
• /
• 2010

This paper and the rear passivation experiment was local back surface field Nd:$YVO_4$ green laser and the experiment was used performed to screen printing. Laser power 100%, with a fixed frequency for 60kHz Current of 29A and 30A were tested in two conditions. The point contact distances of 0.2mm, 0.4mm, 0.6mm, 0.8mm and 29A and 30A current conditions, it was found that is suitable for 0.4mm.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.538-543
• /
• 2008

A roller with a shaft and hot oil paths for pressing electrodes of polymer batteries were modeled and analyzed by FEM. There are many hot oil tubes in the roller and shaft, through which $72^{\circ}C$ hot oil flows for heating the surface of a roller and shaft. Thermal deformations and temperatures distributions of the roller and shaft were calculated and a convection boundary condition on surfaces was used. The influence of existence of a groove in the shaft on the flatness of a roller surface caused by thermal deformation was investigated. In addition, the amount of spring-back of electrodes under vacuum pressure and heating was calculated after the hot rolling process. It was shown from this study that the groove in one shaft had a favorable effect on the surface flatness.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.216-216
• /
• 2012

The purpose of this work is to investigate a back surface field (BSF) on variety wafer resistivity for industrial crystalline silicon solar cells. As pointed out in this manuscript, doping a crucible grown Cz Si ingot with Ga offers a sure way of eliminating the light induced degradation (LID) because the LID defect is composed of B and O complex. However, the low segregation coefficient of Ga in Si causes a much wider resistivity variation along the Ga doped Cz Si ingot. Because of the resistivity variation the Cz Si wafer from different locations has different performance as know. In the light of B doped wafer, we made wider resistivity in Si ingot; we investigated the how resistivities work on the solar cells performance as a BSF quality.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.54.2-54.2
• /
• 2009

결정질 실리콘 태양전지의 알루미늄 후면전극이 패시베이션층의 공극을 통하여 확산됨으로써 국부 후면전계(local back surface field)가 형성되는 후면 점접촉 구조를 제조하였으며, 이에 대한 공정조건 및 특성을 연구하였다. 후면 패시베이션층은 실리콘 기판과 금속전극사이에 삽입됨으로써 표면 재결합속도를 낮추고, 후면 반사도를 높여 광흡수 경로를 증가시킬 수 있다. 고가의 사진식각기술 대신에 저가의 단순한 공정인 레이저 식각기술을 사용하여 후면 패시베이션층에 균일하고 잘 정렬된 공극 패턴을 형성할 수 있었다. 레이저 식각 조건 및 소성조건에 따른 Al 확산 국부 후면전계의 단면 형상을 주사전자현미경(SEM)을 사용하여 관찰하였으며 이에 대한 전기적, 광학적 특성 변화를 조사하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.6
• /
• pp.58-65
• /
• 2007

The arbitrarily-bended pipe is widely used in a heat exchanger system. Thus, the pipe bending process has important role in performance and productivity of heat exchanger system. The purpose of this study is to investigate the bending process for manufacturing of sound pipe. And, the spring-back effect and the variation of pipe thickness should be controlled effectively. The change of spring-back ratio and the thickness variation of pipe according to the change of bending radius, bending angle and pipe thickness are analyzed by FEM analysis. The analytic results are compared with the experimental data, accordingly the results show good agreement. The method of the analysis can be applied for manufacturing of precision bended pipe.