• Current Photovoltaic Research
• /
• v.2 no.1
• /
• pp.1-7
• /
• 2014

We developed a method of growing thin Si film at $600^{\circ}C$ by hot wire CVD using a very thin large-grained poly-Si seed layer for thin-film Si solar cells. The seed layer was prepared by crystallizing an amorphous Si film by vapor-induced crystallization using $AlCl_3$ vapor. The average grain size of the p-type epitaxial Si layer was about $20{\mu}m$ and crystallographic defects in the epitaxial layer were mainly low-angle grain boundaries and coincident-site lattice boundaries, which are special boundaries with less electrical activity. Moreover, with a decreasing in-situ boron doping time, the mis-orientation angle between grain boundaries and in-grain defects in epitaxial Si decreased. Due to fewer defects, the epitaxial Si film was high quality evidenced from Raman and TEM analysis. The highest mobility of $360cm^2/V{\cdot}s$ was achieved by decreasing the in-situ boron doping time. The performance of our preliminary thin-film solar cells with a single-side HIT structure and $CoSi_2$ back contact was poor. However, the result showed that the epitaxial Si film has considerable potential for improved performance with a reduced boron doping concentration.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.6
• /
• pp.387-392
• /
• 2017

A high-performing all-transparent photodetector was created by configuring a $MoO_x$/NiO/ZnO/ITO structure on a glass substrate. The ITO bottom layer was applied as a back contact. To achieve the transparent p/n junction, p-type NiO was coated on the n-type ZnO layer. Reactive sputtering was used to spontaneously form the ZnO or NiO layer. In order to improve the transparent photodetector performance, the functional $MoO_x$ window layer was used. Optically, the $MoO_x$ window provided a refractive index layer (n=1.39) lower than that of NiO (n=2), increasing the absorption of the incident light wavelengths (${\lambda}s$). Moreover, the $MoO_x$ window can provide a lower sheet resistance to improve the carrier collection for the photoresponses. The $MoO_x$/NiO/ZnO/ITO device showed significantly better photoresponses of 877.05 (at ${\lambda}$=460nm), 87.30 (${\lambda}$=520 nm), and 30.38 (${\lambda}$=620 nm), compared to 197.28 (${\lambda}$=460 nm), 51.74 (${\lambda}$=520 nm) and 25.30 (${\lambda}$=620 nm) of the NiO/ZnO/ITO device. We demonstrated the high-performing transparent photodetector by using the multifunctional $MoO_x$ window layer.

• 한국HCI학회:학술대회논문집
• /
• 2008.02a
• /
• pp.337-341
• /
• 2008

This paper presents a vibrotactile space mouse which use pin-type vibrotactile display modules and a gyroscope chip. This mouse is a new interface device which is not only an input device as an ordinary space mouse but also a tactile output device. It consists of a space mouse which use gyroscope chip and vibrotactile display modules which have been developed in our own laboratory. Lately, by development of vibrotactile display modules which have small size and consume low power, vibrotactile displays are available in small sized embedded systems such as wireless mouses or mobile devices. Also, development of new sensors like miniature size gyroscope by MEMS technology enables manufacturing of a small space mouse which can be used in the air not in a plane. The vibrotactile space mouse proposed in this paper recognizes motion of a hand using the gyroscope chip and transmits the data to PC through Bluetooth. PC application receives the data and moves pointer. Also, 2 by 3 arrays of pin-type vibrotactile actuators are mounted on the front side of the mouse where fingers of a user's hand contact, and those actuators could be used to represent various information such as gray-scale of an image or Braille patterns for visually impared persons.

• Journal of Hydrogen and New Energy
• /
• v.21 no.6
• /
• pp.487-492
• /
• 2010

For developing a two-stroke free-piston hydrogen engine with high efficiency and low emission, determination of the scavenging type is one of the most important factor. In this research, backfire characteristics for loop scavenging were analyzed with the number of piston crevice volume and piston expansion speed. Rapid Compression Expansion Machine, RCEM was used for combustion research of the free piston $H_2$ engine in the experiment. As the results, it was shown that although backfire occurring in a loop scavenging type can be partially controled by a complete exhaust of burned gas, possibility of backfire basically exist due to the structure which piston crevice volumes contact with fresh mixture in a scavenging port. However, a loop scavenging may be considered as combustion chamber of a free piston $H_2$ engine from the point of view that backfire does not occur nearby lean equivalence ratio obtained high thermal efficiency. It was also analyzed that an advances of backfire occurrence timing with increase of the fuel-air equivalence ratio were due to promotion of flame propagation into piston crevice volumes by decrease of the quenching distance.

• Journal of Fashion Business
• /
• v.20 no.6
• /
• pp.94-110
• /
• 2016

A necessity for infants, diapers are not only used over long durations, but are also in direct contact to the infants' skin, making the choice of diaper to be of utmost importance. Current interest in cloth diapers is rapidly increasing because of issues concerning the baby's health, green environment, and economy. However, previous researches on cloth diapers are limited to simply investigating the form and material of commercial cloth diapers. There are few in-depth researches for the optimal cloth diaper development. This is therefore a fundamental research for the development of optimized cloth diapers, and analyzes the difference in absorption depending on the placement of seam line (liner, darts, and I pattern), the locations of liquid spraying (1 cm and 8 cm ahead of the center), and the amount of liquid capacity (10 and 20 ml). Currently, the development of diaper patterns considers the crotch shape of the infants and the skin length deformation. As a result, in the case of the I-pattern, the horizontal seam line prevents water from spreading to the front and back, thus reducing the absorbed area. This result was more clearly visible when water was sprayed at the center. The effect of the seam line became more obvious when there was more water (20 ml); also, when water was sprayed at the center, more leakage was observed. Using the results of this research, implementation of horizontal seam is expected to prevent the upward spread of urine.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.20 no.1
• /
• pp.27-32
• /
• 2000

In this paper, ultrasonic wave in the thermoelastic regime was generated in a steel disk by illuminating a pulse laser (Q-switched Nd:YAG) on the surface of the sample and was detected on the other side by Michelson interferometer which was stabilized by feed back control. The experimentally detected displacement waveform of the ultrasonic wave showed good agreement with the theoretically expected one. Also it was shown that sound speeds of longitudinal and shear wave were similar to ones measured by pulse-echo method using a contact transducer. As an application of the noncontact ultrasonic measurement by using laser based ultrasonics, the sound speed in the sample was monitored while the sample was heated in a furnace, and the result showed that it decreased according to the increase of sample temperature.

• Korean Journal of Materials Research
• /
• v.26 no.8
• /
• pp.422-426
• /
• 2016

With the increase in installed solar energy capacity, comparison and analysis of the physical property values of solar cells are becoming increasingly important for production. Therefore, research on determining the physical characteristic values of solar cells is being actively pursued. In this study, a diode equation, which is commonly used to describe the I-V behavior and determine the electrical characteristic values of solar cells, was applied. Using this method, it is possible to determine the diode ideality factor (n) and series resistance ($R_s$) based on light I-V measurements. Thus, using a commercial screen-printed solar cell and an interdigitated back-contact solar cell, we determined the ideality factor (n) and series resistance ($R_s$) with a modified diode equation method for the light I-V curves. We also used the sun-shade method to determine the ideality factor (n) and series resistance ($R_s$) of the samples. The values determined using the two methods were similar. However, given the error in the sun-shade method, the diode equation is considered more useful than the sun-shade method for analyzing the electrical characteristics because it determines the ideality factor (n) and series resistance ($R_s$) based on the light I-V curves.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.1
• /
• pp.50-66
• /
• 2010

This Shanghai region study is a sample survey of female college students in their early 20s. This study collected and analyzed the information of shapes through a direct contact survey to understand the breast figures and the measurements of bodies to provide basic information to improve brassiere production for adult females in China. Data was analyzed through a SAS 9.0. The characteristic of the final brassiere pattern that had been corrected and complemented from the results of the $l^{st},\;2^{nd},\;3^{rd}$, and $4^{th}$ fitting tests is defined as a brassiere inserted with a round wire that has the 3/4cup to wrap the bust area by about 3/4. It consists of an upper and lower nonwoven fabric cup that has a flat-shaped wing of a circular dart. The drawing method of the pattern of this brassiere is applied with the conditions to cover the body naturally under the diverse and organic relations of the material factor of stretch material and wire, functional factor, and sewing factor. The final pattern is created as a bigger angle of wing pattern and a short inner side diameter because there are more Chinese women with a back of bending figure compared to Korean women.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.10
• /
• pp.1370-1374
• /
• 2018

A heterojunction $SnS_2/p-Si$ photodetector was fabricated by RF magnetron sputtering system. $SnS_2$ was formed with 2-inch $SnS_2$ target. Al was applied as the front and the back metal contacts. Rapid thermal process was conducted at $500^{\circ}C$ to enhance the contact quality. 2D material such as $SnS_2$, MoS2 is very attractive in various fields such as field effect transistors (FET), photovoltaic fields such as photovoltaic devices, optical sensors and gas sensors. 2D material can play a significant role in the development of high performance sensors, especially due to the advantages of large surface area, nanoscale thickness and easy surface treatment. Especially, $SnS_2$ has a indirect bandgap in the single and bulk states and its value is 2 eV-2.6 eV which is considerably larger than that of the other 2D material. The large bandgap of $SnS_2$ offers the advantage for the large on-off current ratio and low leakage current. The $SnS_2/p-Si$ photodetector clearly shows the current rectification when the thickness of $SnS_2$ is 80 nm compared to when it is 135 nm. The highest photocurrent is $19.73{\mu}A$ at the wavelength of 740 nm with $SnS_2$ thickness of 80 nm. The combination of 2D materials with Si may enhance the Si photoelectric device performance with controlling the thickness of 2D layer.

• Journal of the Korean Society of Costume
• /
• v.59 no.3
• /
• pp.82-95
• /
• 2009

The kind and the use of the fabrics for crown manufacture in the Baekje period has been studied by characterizing the imprinted fabrics on the crowns and the diadem ornaments from the old tomb. The contact region with the skin inside of the crown and the region between the bark of white birch and the gilt bronze openwork plates contained fabrics. The fabrics used in the gilt-bronze crown were all plain weave silk except that of Yongwonri tomb where loosely woven thin tabby was used. There have been 4-types of iron framed diadem of the Baekje, which comprise the inverted triangle-shaped diadem only with iron frame, the diadem with gold plate ornament in the iron frame, the diadem decorated with mica plate and gold plate, and the diadem with silver ornament in the iron frame. The fabrics used in the triangle shaped iron frame diadem include plain weave silk, irregular plain woven silk, thin tabby, complex silk gauze, twill weave on plain ground, and warp-faced compound weave. The iron frames were wrapped with the fabrics from one layer up to three layers, and the iron diadem was covered with one later of loosely woven textile such as irregular plain woven silk, thin tabby, and complex silk gauze. But in case of decorating the iron diadem with gold Plate ornaments, multiple layers of fabric were used to sustain the weight of the ornaments. The fabrics in the iron diadem frame were sewed with running stitch, overedge stitch or hemming stitch, diagonal hemming stitch, half back stitch), and overcast stitch.