• 토지주택연구
• /
• 제8권4호
• /
• pp.257-266
• /
• 2017

LH has been using ultra high strength reinforcing bars (SD500 and SD600), since 2011. Such a change requires an adjustment of the old extra rates of bar splice to reflect use of ultra high strength reinforcing bars, as these rates had been set based on SD400 bars. It is particularly difficult to calculate precisely rebar lap-splice locations for large areas, such as those in apartment buildings. This research aims to adjust the extra rates of bar splice to reflect a reasonable rate; the rebar lap-splice length is not an exact estimation, but instead, an extra rates of bar splice is set and the rebar lap-splice length is increased by 2% (D 10) - 7% (025) depending on the bar size. The subjects of this study are LH apartments undergoing frame construction. We studied the quantity estimations from the design drawings, and analyzed the settlement quantities of construction field. The results of the study revealed that, when each of the quantities are analyzed, consider adjusting the extra rates of bar splice of some rebar to 1% - 3.5%. This was caused by an overuse of reinforcing bars in onsite construction and the use of supporting bars that have not been reflected in the documents, among other reasons. Based on the results of our study, an improvement plan for the current extra rates of bar splice seems to be necessary, cutting or raising the rate depending on the analysis of the data. Through this study, we expect to contribute to the calculation of reasonable construction costs, improvements in the quality of rebar work, and improvements in the capacity of design techniques for apartment buildings.

• Journal of Communications and Networks
• /
• 제16권5호
• /
• pp.548-558
• /
• 2014

Load distribution is vital to the performance of multipath transport. The task becomes more challenging in real-time multimedia applications (RTMA), which impose stringent delay requirements. Two key issues to be addressed are: 1) How to minimize end-to-end delay and 2) how to alleviate packet reordering that incurs additional recovery time at the receiver. In this paper, we propose sub-packet based multipath load distribution (SPMLD), a new model that splits traffic at the granularity of sub-packet. Our SPMLD model aims to minimize total packet delay by effectively aggregating multiple parallel paths as a single virtual path. First, we formulate the packet splitting over multiple paths as a constrained optimization problem and derive its solution based on progressive approximation method. Second, in the solution, we analyze queuing delay by introducing D/M/1 model and obtain the expression of dynamic packet splitting ratio for each path. Third, in order to describe SPMLD's scheduling policy, we propose two distributed algorithms respectively implemented in the source and destination nodes. We evaluate the performance of SPMLD through extensive simulations in QualNet using real-time H.264 video streaming. Experimental results demonstrate that: SPMLD outperforms previous flow and packet based load distribution models in terms of video peak signal-to-noise ratio, total packet delay, end-to-end delay, and risk of packet reordering. Besides, SPMLD's extra overhead is tiny compared to the input video streaming.

• 한국콘텐츠학회논문지
• /
• 제5권2호
• /
• pp.187-197
• /
• 2005

본 논문에서는 위치 기반 서비스에서 이동 객체의 궤적을 색인하기 위해 기존에 제안되었던 TB-트리의 성능을 개선시킬 수 있는 확장된 TB-트리(Extented TB-Tree:ETB-Tree)를 제안한다. ETB-트리는 선행 노드를 직접적으로 접근하기 위해 이동 객체의 처음 세그먼트와 마지막 세그먼트가 저장된 단말 노드를 가리키는 포인터 정보와 더불어 디스크에서의 페이지를 가리키는 페이지 번호를 별도의 테이블에 같이 유지함으로써 저장시 동일한 이동 객체의 선행노드를 빨리 검색할 수 있고, 궤적 질의시에도 바로 디스크에 접근해 해당 객체의 제적들을 검색함으로써 검색 성능을 향상시킬 수 있다. 아울러 ETB-트리는 새로운 이동 객체의 제적 정보가 삽입될 때마다 메모리 상의 트리 구조 뿐만 아니라 디스크에 반영함으로써 트리의 일관성을 유지한다. 마지막으로, 성능 평가를 분석한 결과, 제안하는 색인 기법이 기존의 색인 기법들에 비해 삽입과 제적 질의의 검색 측면에서 더 우수함을 보임을 알 수 있다.

• 한국운동역학회지
• /
• 제27권1호
• /
• pp.35-43
• /
• 2017

Objective: The purpose of this study was to determine how gaze angle affects muscle activity and kinematic variables during treadmill walking and to offer scientific information for effective and safe treadmill training environment. Method: Ten male subjects who have no musculoskeletal disorder were recruited. Eight pairs of surface electrodes were attached to the right side of the body to monitor the upper trapezius (UT), rectus abdominis (RA), erector spinae (ES), rectus femoris (RF), bicep femoris (BF), tibialis anterior (TA), medialis gastrocnemius (MG), and lateral gastrocnemius (LG). Two digital camcorders were used to obtain 3-D kinematics of the lower extremity. Each subject walked on a treadmill with a TV monitor at three different heights (eye level; EL, 20% above eye level; AE, 20% below eye level; BE) at speed of 5.0 km/h. For each trial being analyzed, five critical instants and four phases were identified from the video recording. For each dependent variable, one-way ANOVA with repeated measures was used to determine whether there were significant differences among three different conditions (p<.05). When a significant difference was found, post hoc analyses were performed using the contrast procedure. Results: This study found that average and peak IEMG values for EL were generally smaller than the corresponding values for AE and BE but the differences were not statically significant. There were also no significant changes in kinematic variables among three different gaze angles. Conclusion: Based on the results of this study, gaze angle does not affect muscle activity and kinematic variables during treadmill walking. However, it is interesting to note that walking with BE may increase the muscle activity of the trapezius and the lower extremity. Moreover, it may hinder proper dorsiflexion during landing phase. Thus, it seems to reasonable to suggest that inappropriate gaze angle should be avoided in treadmill walking. It is obvious that increased walking speed may cause a significant changes in biomechanical parameters used in this study. It is recommended that future studies be conducted which are similar to the present investigation but using different walking speed.

• 생약학회지
• /
• 제47권1호
• /
• pp.79-83
• /
• 2016

This study developed an HPLC analysis method for the determination of isoegomaketone (IK) and perillaketone (PK) in Perilla frutescens (L.) Britton leaves. P. frutescens ethanol extract was optimized through an HPLC analysis using a C18 column ($250{\times}4.6mml$, D, $S-5{\mu}m$, 12 nm) with gradient elution of water and acetonitrile as the mobile phase at a flow rate of 1 mL/min and a UV detection wavelength of 254 nm. The results of this method showed linearity in the calibration curve at a coefficient of correlation ($R^2$) of IK 0.9995, PK 0.9998. The limits of detection (LOD) for IK and PK were $0.234{\mu}g/mL$ and $0.952{\mu}g/mL$. The limits of quantification (LOQ) for IK and PK were $0.017{\mu}g/mL$ and $0.043{\mu}g/mL$. The inter-day precision RSDs of IK and PK in the P. frutescens were 1.25 to 2.69% and 0.36 to 1.10%, respectively, and the intra-day precision RSDs of IK and PK were 0.96 to 2.51% and 0.90 to 1.93%, respectively. The accuracies of IK and PK were 96.31 to 97.92% and 101.26 to 105.14%. In conclusion, this method was applied successfully to the detection of IK and PK in P. frutescens.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.196-196
• /
• 2011

Molecular $N_2O$ has bee known to react over oxygen vacancy on a reduced rutile $TiO_2$(110)-1${\times}$1 surface to desorb as molecular $N_2$ leaving oxygen atom behind. In the present study, we investigated the reaction of $N_2O$ on rutile $TiO_2$(110) using temperature-programmed desorption (TPD). Our results indicate that $N_2O$ does not react over the oxygen vacancy under a typical UHV experimental condition. On a rutile $TiO_2$(110)-1${\times}$1 with a well-defined oxygen vacancy concentration of 5% ($2.6{\times}10^{13}/cm^2$), $N_2O$ desorption features show a monolayer peak maximum at 135 K followed by a small peak maximum at 170 K. When the oxygen vacancy is blocked with $H_2O$, the $N_2O$ peak at 170 K disappears completely, indicating that the peak is due to molecular $N_2O$ interacting with oxygen vacancy. The integrated amount of desorbed $N_2O$ plotted against the amount of adsorbed $N_2O$ however shows a straight line with no offset indicating no loss of $N_2O$ during our cycles of TPD measurements. In addition, our $N_2O$ uptake measurements at 70~100 K showed no $N_2$ (as a reaction product) desorption except contaminant $N_2$. Also, $H_2O$ TPD taken after $N_2O$ scattering up to 350 K indicates no change in the vacancy-related $H_2O$ desorption peak at 500 K showing no change in the oxygen vacancy concentration after the interaction with $N_2O$.

• 한국의류학회지
• /
• 제31권8호
• /
• pp.1190-1201
• /
• 2007

This study is to review the costumes of female Shamans through Gamrotaenghwa(甘露幀畵) in the late Joseon Dynasty of the 18th and 19th centuries. The picture of Mudangnaeryeok(巫堂來歷) showing Shamanic performances which is kept in Kyujanggak, Seoul National University was the only one thing enabling to compare with the Shamanic costumes shown in Gamrotaenghwa. The earlier Gamrotaenghwa doesn't show the Shamanic features but that of the later part of 18th century shows specific costumes so that the scene of Shamanic performance can be guessed. The Shamanic costumes are classified into 5 types. Type A is considered to have followed the figures shown commonly in earlier Gamrotaenghwa of the 16th and 17th centuries, rather than the traditional costumes. Types B through E show the costumes of the Joseon dynasty. With the basic costumes of skirt and Chogori(a kind of jacket, Type B), the variable costumes worn for each type of Shamanic performances are Mongduri(蒙頭里, Type C), Jeonbok(戰服, Type D) and Cheolrik(天翼, Type E). Reviewing the general style of those costumes, the upper part was tight and the lower part was silhouette of big volume, and the length of Chogori was a little long in the early of 18th century but it became shorter with narrower sleeves from the later part of the same century. According to the general literatures about the outer collars were not overlapped and its side parts were open, with half or no sleeves. In case that the target of Shamanic performance is male god, the Shaman wore the male costumes represented by Cheolrik and Jeonbok. Because these Cheolrik and Jeonbok which were worn during the Shamanic performance have the symbolic meaning to correspond with the male god, they didn't function as ordinary costumes.

• Ocean and Polar Research
• /
• 제32권3호
• /
• pp.309-319
• /
• 2010

To assess community structure and diversity of archaea, a clone sequencing analysis based on an archaeal 16S rRNA gene was conducted at three sediment depths of the continental slope and Ulleung Basin in the East Sea. A total of 311 and 342 clones were sequenced at the slope and basin sites, respectively. Marine Group I, which is known as the ammonia oxidizers, appeared to predominate in the surface sediment of both sites (97.3% at slope, 88.5% at basin). In the anoxic subsurface sediment of the slope and basin, the predominant archaeal group differed noticeably. Marine Benthic Group B dominated in the subsurface sediment of the slope. Marine Benthic Group D and Miscellaneous Crenarchaeotal Group were the second largest archaeal group at 8-9 cm and 18-19 cm depth, respectively. Marine Benthic Group C of Crenarchaeota occupied the highest proportion by accounting for more than 60% of total clones in the subsurface sediments of the basin site. While archaeal groups that use metal oxide as an electron acceptor were relatively more abundant at the basin sites with manganese (Mn) oxide-enriched surface sediment, archaeal groups related to the sulfur cycle were more abundant in the sulfidogenic sediments of the slope. Overall results indicate that archaeal communities in the Ulleung Basin show clear spatial variation with depth and sites according to geochemical properties the sediment. Archaeal communities also seem to play a significant role in the biogeochemical carbon (C), nitrogen (N), sulfur (S), and metal cycles at each site.

• ETRI Journal
• /
• 제24권3호
• /
• pp.211-220
• /
• 2002

This study characterizes an oxide etching process in a magnetically enhanced reactive ion etching (MERIE) reactor with a $CHF_3/CF_4$ gas chemistry. We use a statistical $2^{4-1}$ experimental design plus one center point to characterize the relationships between the process factors and etch responses. The factors that we varied in the design include RF power, pressure, and gas composition, and the modeled etch responses were the etch rate, etch selectivity to TiN, and uniformity. The developed models produced 3D response plots. Etching of $SiO_2$ mainly depends on F density and ion bombardment. $SiO_2$ etch selectivity to TiN sensitively depends on the F density in the plasma and the effects of ion bombardment. The process conditions for a high etch selectivity are a 0.3 to 0.5 $CF_4$ flow ratio and a -600 V to -650 V DC bias voltage according to the process pressure in our experiment. Etching uniformity was improved with an increase in the $CF_4$ flow ratio in the gas mixture, an increase in the source power, and a higher pressure. Our characterization of via etching in a $CHF_3/CF_4$ MERIE using neural networks was successful, economical, and effective. The results provide highly valuable information about etching mechanisms and optimum etching conditions.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2017년도 춘계학술대회
• /
• pp.205-206
• /
• 2017

2016년 7000만 달러를 투자해 스마트폰 기반 캐주얼 게임을 각색한 3D 애니메이션 영화 <앵그리버드>가 상영된 후 전 세계적으로 누적 흥행 수입 5.14억 달러를 초과하는 등 큰 성공을 이루었다. 게임을 각색한 영화에서 입소문과 흥행 성적이 모두 좋았던 성공 사례는 매우 드물다. 구체적인 이야기 줄거리, 캐릭터 그리고 세계관이 없는 스마트폰 기반 캐쥬얼 게임을 어떻게 대중들의 사랑을 한 몸에 받는 상업 영화로 각색할 수 있었는지가 본 연구 목적이다. 본 연구는 먼저 스마트폰 기반 캐쥬얼 게임 <앵그리 버드>와 대형 온라인 게임 <와우>에 대해 비교를 진행하여 각색함에 있어서 장단점을 비교하고자 한다. 다음 <앵그리 버드>의 게임과 영화를 비교하여 두 매체 속에 존재하는 핵심요인 간 차이를 분석하고 설문조사를 통한 관객 평가 결과를 참조하여 가장 관객들의 인정을 받는 영화의 요소와 이런 종류의 영화에 대한 관객의 태도는 어떠한지를 알아보고자 한다.