• Wind and Structures
• /
• v.35 no.5
• /
• pp.353-368
• /
• 2022

Wind turbine blades are adjusted in real-time according to the wind conditions and blade deformations to improve power generation efficiency. It is necessary to predict and reduce the aeroelastic deformations of wind turbine blades. In this paper, the equivalent model of the blade is established by the finite element method (FEM), and the aerodynamic load of the blade is evaluated based on the blade element momentum (BEM) theory. The aeroelastic coupling model is established, in which the bending-torsion coupling effect of the blade is taken into account. The steady and dynamic aeroelastic deformations are calculated. The influences of the blade section's shear centre position and the blade's sweepback design on the deformations are analyzed. The novel approaches of reducing the twist angle of the blade by changing the shear centre position and sweepback of the blade are presented and proven to be feasible.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.4
• /
• pp.500-509
• /
• 2015

The numerical simulation of two-dimensional moving blade row interactions is conducted by CFD means to investigate the interactions between the front and rear propeller in a stratospheric airship contra-rotating open propeller configuration caused by different rotational speeds. The rotational speed is a main factor to affect the propeller Reynolds number which impact the aerodynamic performance of blade rows significantly. This effect works until the Reynolds number reaches a high enough value beyond which the coefficients become independent. Additionally, the interference on the blade row has been revealed by the investigation. The front blade row moves in the induced-velocity field generated by the rear blade row and the aerodynamic coefficients are influenced when the rear blade row has fast RPMs. The rear blade row moving behind the front one is affected directly by the wake and eddies generated by the front blade row. The aerodynamic coefficients reduce when the front blade row has slow RPMs while increase when the front blade row moves faster than itself. But overall, the interference on the front blade row due to the rear blade row is slight and the interference on the rear blade row due to the front blade row is much more significant.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.2
• /
• pp.105-111
• /
• 2013

Whirl tower test is conducted basically during helicopter rotor system development process. And for whirl tower test of rotor hub system, new design blade or existing blade which is remodeled for new rotor hub system is used. Because of simple shape and efficient aerodynamic characteristic, BO-105 helicopter blade is used for helicopter rotor hub development project widely. Originally BO-105 blade is used for hingeless hub system and blade root is used to flexure. So flap stiffness and lag stiffness at blade root area is relatively low compare with airfoil area. So, in order to apply the BO-105 blade to bearingless hub, blade root area have to be reinforced. And in this process, blade root area's section property is changed. In this paper, we suggest reinforcement method of BO-105 blade root area and study dynamic characteristic of bearingless rotor system with reinforcement BO-105 blade.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.4 s.9
• /
• pp.30-37
• /
• 2000

Several reverse design methods are developed and applied to the suction or pressure surface for finding design values of blade geometry for a given axial turbine blade. Re-designed blade profiles using shape parameters are compared with measured blade data. Essential shape parameters for blade design are induced by the procedure of reverse design for best fitting. Characteristics of shape parameters are evaluated through the system design method and restriction conditions of structural stability or aerodynamic flow loss. Some of shape parameters i.e blade radius or exit blade angle etc., are classified to weakly adjustable shape parameters, otherwise strongly adjustable shape parameters which would be applied for controlling blade shape. Average deviation values between the measured data and re-designed blade using shape parameters are calculated for each design method. Comparing with the average deviation for a given blade geometry, minimum shape parameters required to design a blade geometry are obtained.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.448-448
• /
• 2009

A new blade has been developed to apply to Doosan 3MW offshore wind turbine named as WinDS3000TM. The 3MW blade has been designed by the concept of slim external shape and optimized structure. High-performance glass fiber reinforced epoxy composites were used as the main material of the blade. The blade was manufactured using vacuum infusion process in order to increase the fiber volume fraction and to reduce micro-porosities. The blade has successfully passed the full-scale blade static test for certification. During the test, micro-failure signal and strain change of the blade were measured using acoustic emission sensors and strain gages. The blade has robust structure and weighs lighter compared to conventional blade since the new blade was designed by optimization process. The 3MW blade will be commercially applied to WinDS$3000^{TM}$ in 2010.

• The KSFM Journal of Fluid Machinery
• /
• v.8 no.4 s.31
• /
• pp.27-38
• /
• 2005

The present study investigated the effect of relative position of the blade on blade surface heat transfer. The experiments were conducted in a low speed wind tunnel with a stationary annular turbine cascade. The test section has a single turbine stage composed of sixteen guide vanes and blades. The chord length of the blade is 150 mm and the mean tip clearance of the blade is $2.5\%$ of the blade chord. The Reynolds number based on blade inlet velocity and chord length is $1.5{\times}105$ and mean turbulence intensity is about $3\%$. To investigate the effect of relative position of blade, the blade at six different positions in a pitch was examined. For the detailed mass transfer measurements, a naphthalene sublimation technique was used. In general, complex heat transfer characteristics are observed on the blade surface due to various flow characteristics, such as a laminar flow separation, relaminarization, flow acceleration, transition to turbulence and tip leakage vortices. The results show that the blade relative position affects those heat transfer characteristics because the distributions of incoming flow velocity and turbulence intensity are changed. Especially, the heat transfer pattern on the near-tip region is significantly affected by the relative position of the blade because the effect of tip leakage vortex is strongly dependent on the blade position. On the pressure side, the effect of blade position is not so significant as on the suction side surface although the position and the size of the separation bubble are changed.

• The Korean Journal of Emergency Medical Services
• /
• v.22 no.3
• /
• pp.35-45
• /
• 2018

Purpose: The purpose of this study was to compare laryngoscopic views and ease of use and success of intubation, via the percentage of glottic opening (POGO) scale when using the Miller blade and Macintosh blade in paraglossal approach. Methods: Forty intern doctors were randomized for laryngoscopy to be performed in a crossover manner. They performed endotracheal intubation with Miller blade and Macintosh blade in two airway scenarios: normal airway and difficult airway with edema. We observed the rate of successful intubation, time required for visualizing the glottis, time to complete endotracheal intubation, ease of intubation, and the POGO scale. Results: In the normal airway, there was no difference in intubation between the two endoscopes. In the difficult airway, the time for visualizing the glottis (7.80 versus 10.24 sec; p=.006), the time to tube passage (19.38 versus 23.03 sec; p=.038) and the time to complete endotracheal intubation (21.84 versus 28.54 sec; p=.022) with Miller blade was shorter than with Macintosh blade. The POGO scale(%) of the Miller blade was higher than that of the Macintosh blade's (62.25 versus 56.32; p=.030). Conclusion: Compared to the Macintosh blade, Miller blade provided better visualization of the glottis and POGO scale, and faster time to completion of endotracheal intubation.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.85-89
• /
• 2004

The inner side between HP stationary blades in #1 turbine of Nuclear Power Plant A is damaged by the FAC(flow assisted corrosion) which is exposed to moisture. For many years the inner side is repaired by welding the damaged part, however, FAC continues to deteriorate the original material of the welded blade ring. In this study, we have two stages to verify the integrity of stationary blade ring in nuclear power plant A. In the stage I, replication of blade ring is performed to survey the microstructure of blade ring. In the stage II, the stress analysis of blade ring is performed to verify the structural safety of blade ring. Throughout the two stages analysis of blade ring, the stationary blade ring had remained undamaged.

• Wind and Structures
• /
• v.16 no.3
• /
• pp.241-248
• /
• 2013

The wind turbine blade is a very important part of the rotor. Extraction of energy from wind depends on the design of blade. In this work, the analysis is done on a blade of length 38.95 m which is designed for V82-1.65 MW horizontal axis wind turbine (supplied by Vestas). The airfoil taken for the blade is NACA 634-221 which is same from root to tip. The analysis of designed blade is done in flap-wise loading. Two shapes of the spar are taken, one of them is of square shape and the other one is combination of square and cross shape. The blade and spar are of the same composite material. The Finite element analysis of designed blade is done in ANSYS. This work is focused on the two segments of blade, root segment and transition segment. Result obtained from ANSYS is compared with the experimental work.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.236-241
• /
• 2011

An active trailing-edge flap blade named as Seoul National University Flap (SNUF) blade is designed for reducing helicopter vibratory loads and the relevant aeroacoustic noise. Unlike the conventional rotor control, which is restricted to 1/rev frequency, an active control device like the present trailing-edge flap is capable of actuating each individual blade at higher harmonic frequencies i.e., higher harmonic control (HHC) of rotor. The proposed blade is a small scale blade and rotates at higher RPM. The flap actuation components are located inside the blade and additional structures are included for reinforcement. Initially, the blade cross-section design is determined. The aerodynamic loads are predicted using a comprehensive rotorcraft analysis code. The structural integrity of the active blade is verified using a stress-strain recovery analysis.