In Korea, attempts have been made to develop high strength concrete for the safety and design life improvement of nuclear power plants. In this study, the cracking potentials of nuclear power plant-high strength concretes (NPP-HSCs) containing industrial by-products with W/B 0.34 and W/B 0.28, which are being reviewed for their application in the construction of containment structures, were evaluated through autogenous shrinkage, unrestrained drying shrinkage, and restrained drying shrinkage experiments. The cracking potentials of the NPP-HSCs with W/B 0.34 and W/B 0.28 were in the order of 0.34FA25 > 0.34FA25BFS25 > 0.34BFS50 > 0.34BFS65SF5 and 0.28FA25SF5 >> 0.28BFS65SF5 > 0.28BFS45SF5 > 0.28 FA20BFS25SF5, respectively. The cracking potentials of the seven mix proportions excluding 0.28FA25SF5 were lower than that of the existing nuclear power plant concrete; thus, the durability of a nuclear power plant against shrinkage cracking could be improved by applying the seven mix proportions with low cracking potentials.
Lee Kwang-Myong;Kwon Ki-Heon;Lee Hoi-Keun;Lee Seung-Hoon;Kim Gyu-Yong
Journal of the Korea Concrete Institute
/
v.16
no.5
s.83
/
pp.621-626
/
2004
The use of blast-furnace slag (BFS) in making not only normal concrete but also high-performance concrete has several advantages with respect to workability, long-term strength and durability. However, slag concrete tends to show more shrinkage than normal concrete, especially autogenous shrinkage. High autogenous shrinkage would result in severe cracking if they are not controlled properly. Therefore, in order to minimize the shrinkage stress and to ensure the service life of concrete structures, the autogenous shrinkage behavior of concrete containing BFS should be understood. In this study, small prisms made of concrete with water-binder (cement+BFS) ratio (W/B) ranging from 0.27 to 0.42 and BFS replacement level of $0\%$, $30\%$, and $50\%$, were prepared to measure the autogenous shrinkage. Based on the test results, thereafter, material constants in autogenous shrinkage prediction model were determined. In particular, an effective autogenous shrinkage defined as the shrinkage that contributes to the stress development was introduced. Moreover, an estimation formula of the 28-day effective autogenous shrinkage was proposed by considering various W/B's. Test results showed that autogenous shrinkage increased with replacement level of BFS at the same W/B. Interestingly, the increase of autogenous shrinkage is dependent on the W/B at the same content of BFS; the lower W/B, the smaller increasing rate. In concluding, it is necessary to use the combination of other mineral admixtures such as shrinkage reducing admixture or to perform sufficient moisture curing on the construction site in order to reduce the autogenous shrinkage of BFS concrete.
This study investigated the optimal amount of FDKP(Freeze Dried Kimchi powder) to be added in BFS(breakfast sausage) in order to develop a new Korean style processed food, which can be used as a useful export item. The results of the study suggested that BFSs prepared with FDKP were more favored than BFS without FDKP. The specific findings are as follows: The BFS added with 3% FDKP was favored most in color, taste, softness and overall acceptability by the trained sensory panels. However, in case of unbaked BFS, 9% addition of FDKP was found to have preferred color. Overall, this study suggests that 3% of FDKP was optimal for the newly developed Kimchi BFS. On top of that this study also showed possibility of standardization of product using Korean traditional Kimchi.
Proceedings of the Korean Society of Crop Science Conference
/
2022.10a
/
pp.50-50
/
2022
Recently, the use of mulching film has increased in soybean cultivation. Polyethylene (PE) films and biodegradable films (BF) have the advantages of improving soil moisture retention, geothermal maintenance, and CO2 maintenance as well providing weed control. Furthermore, BFs are a material that can compensate for the shortcomings of PE because it has the ability to decompose naturally by soil microorganisms, sunlight, and geothermal heat. Many researches have been carrying out studies regarding the development of BFs for these very reasons. This study was conducted better understand which films are optimal for soybean cultivation after evaluations of soybean growth and film characteristics of various BFs. BFs Farmsbio (Farm Hannong), Heulgro Film (Sejin Bio), Vonto Film (Eco-Hansung), two unnamed biodegradable films (Seojin Bio and Taesung), and a PE film were used in this study. For the control plots, no mulching was used. Experimental fields were fertilized according to conventional cultivation methods, tilled, and then covered with either BFs or PE films. After 1 week, soybean (cv. Daechan) seeds were seeded. Germination rate and plant height were measured at weekly intervals after seeding. In addition, pH, EC, and decomposition and light transmittance levels of films were measured during the experimental period. Daily average temperatures and relative humidity in soils was measured during the experimental period. There was no significant difference in germination rates and plant height in both crops grown with BFs and PE films, but crops grown in the control plot had significantly lower germination rates and growth. Soil pH was not significantly different regardless of treatments (BF, PE, and non-mulching) at 14, 28, and 42 days after seeding. In general, the EC contents in the control plots was lower than in crops grown using BFs and PE films. With the exception of some BFs, light transmittance and decomposition levels of films did not, in general, increase up to 70 days after soybean seeding. Since this study is ongoing, we are continually investigating these parameters. The average daily moisture in soil was higher in crops grown with BFs and PE films than in the control plot. However, the daily average soil temperature was not consistent regardless of treatments. Therefore, the BFs used in this study can be used without negative impacts on soybean growth.
Journal of the Korean Recycled Construction Resources Institute
/
v.8
no.1
/
pp.18-24
/
2013
Recently, the interest is increasing about the eco-friendly concrete. Accordingly, the blast furnace slag(BFS), a by-product of industry is known for improving the durability through compaction in concrete and is expanding the use. The research about BFS in concrete be accomplished frequently. In this study, we should know the hydration characteristic of BFS concrete the through the adiabatic temperature rise test due to the replacement of a variety of BFS. In addition, we produced the regression analysis factors through the test result and analyzied the effect for the replacement of BFS. According to test results, the compressive strength showed a slight degradation or equal and the the adiabatic temperature rise figure and rising factors are went down for rising replacment of BFS. In the future, the study about the adiabatic temperature rise equation for the various replacement of BFS and binder is considered necessary.
Proceedings of the Korean Society of Crop Science Conference
/
2022.10a
/
pp.52-52
/
2022
Recently, PE (polyethylene) film has been used increasingly in com cultivation. However, PE films often cause soil and environment contamination. In order to reduce this problem, many researches have been carrying out studies on biodegradable films (BF) that are easily decomposed by soil microorganisms. Therefore, this study was conducted to determine which BF is optimal for growth and yield of com crops while also having the highest rates of film decomposition. BFs Farmsbio (Farm Hannong), Heulgro Film (Sejin Bio), Vonto Film (Eco-Hansung) as well as a selected PE film were used in this study. For the control, we used crops grown without any kind of mulching. Experimental fields were fertilized according to conventional cultivation methods, tilled, and then covered by either BF or PE. After 1 week, com (cv. MIBECK2ho) at the 3-leaf stage (16 days after seeding) was transplanted. Plant height was measured at 18 and 32 days after transplanting and heading stages. Yield components and yield were also measured at harvest. In addition, pH, EC, and decomposition and light transmittance levels of films were investigated during the experimental period. Daily average temperature, relative humidity and organic matter in soils were also measured during the experimental period. There was no significant difference in plant height, heading date, and silking between crops with BFs and PE, but the crops grown with BFs and PE films reached higher growth parameters in a shorter amount of time than the crops in the non-mulching control. Additionally, there were no significant differences in yield components such as length of ears, ear width, ear weight, and yield in crops that were grown using films or crops in the control plot. Light transmittance and decomposition levels of films generally increased with time after transplanting, and was highest in the Heulgro film than other BFs. Soil pH and organic matter in crops using BFs and PE films were significantly higher than in the control plot at 99 and 113 days after transplanting. In general, the EC contents in the control plot was lower than in crops using BFs and PE films. The average daily moisture in soil was higher when BFs and PE films were used than in the control plot. However, the daily average soil temperature was higher in crops using BFs and PE films than in the control plots at the beginning of the experimental period, but there was no consistent difference in soil temperature towards the later part of the experimental period. Therefore, the BFs used in this study were shown to be helpful without causing negative impacts on the growth and yield of com.
This article describes laboratory research done on strength evaluations for stabilized samples made of tropical fibrous peat. The stabilizing agents used were ordinary Portland cement (OPC) as binding agent and blast furnace slag (BFS) as additive. Stabilized samples were tested for their strength through unconfined compressive strength (UCS) and California bearing ratio (CBR). Different dosage rates of OPC and BFS were used in trial and error experiments for the most effective combination for stabilized peat samples that were at their natural moisture content. Stabilized trial samples were air cured for 90 days. After detecting the most effective dosage rate in the trial samples, their values were used to prepare CBR samples at their optimum moisture content (OMC). CBR samples were then air cured from 1 to 90 days and tested under un-soaked and soaked conditions. The most effective dosage rate for the stabilized peat samples was found to be close to when 75% for OPC and 25% of BFS per total weight of OPC, and BFS. As an example, if 11.25% OPC, and 3.75% BFS are mixed with peat and compacted at their OMC and air cured for 90 days, stabilized peat will have an increase in CBR of 0.8% to 45 % for un-soaked and 20% for soaked conditions.
Rheological properties of cement pastes containing blast furnace slag (BFS: 3,900, $7,910\;cm^2/g$) or fly ash powder (FA: 4,120, $8,100\;cm^2/g$) according to the ratio of water/binder (W/B) and the dosage of polycarboxylate type superplasticizer (PC) were investigated by a mini slump and a coaxial cylinder viscometer. In this experiment, the ratio of replacing OPC with BFS or FA was 30 wt%, the W/B was from 30 to 70 wt%. As a result, the fluidity of cement paste containing BFS or FA was improved with increasing W/B and the dosage of PC. BFS or FA replaced cement paste with W/B 70% and PC 0.3% showed the highest fluidity. The segregation range of cement paste was occurred below $10\;d/cm^2$ of the yield stress and below 50 cPs of the plastic viscosity by the coaxial cylinder viscometer. And also it was formed that the plastic viscosity and the yield stress of FA replaced cement paste were higher than them of BFS replaced cement paste.
Representative bulletproof materials, such as aramid or ultra-high molecular weight polyethylene(UHMWPE), have excellent strength and modulus in the plane direction but are very vulnerable to forces applied in the thickness direction. This paper reports a study on the effects of reinforcement in the thickness direction when bulletproof composite fabrics are prepared to improve their performance. Aramid and UHMWPE fabrics were combined using the film-bonding, needle-punching, or stitching methods and then subjected to low-velocity projectile and ball-drop impact tests. The results of the low-velocity projectile test indicated that the backface signature(BFS) decreased by up to 29.2% in fabrics obtained via the film-bonding method. However, the weight of the film-bonded fabric increased by approximately 23% compared with that obtained by simple lamination, and the fabric stiffened on account of the binder. Flexibility, light weight for wearability, and excellent bulletproof performance are very important factors in the development of bulletproof materials. When the needle-punching method was used, the BFS increased as the fibers sustained damage by the needle. When the composite fabrics were combined by stitching, no significant difference in weight and thickness was observed, and the BFS showed similar results. When a diagonal stitching pattern was employed, the BFS decreased as the stitching density increased. By contrast, when a diamond stitching pattern was used, the fabric fibers were damaged and the BFS increased as the stitching density increased.
Autogenous healing of concrete can be helpful in structural maintenance by healing cracks using a healing material created by the precipitation of calcite and by the hydration of unhydrated binder around the cracks. Against this backdrop, this study investigated the physicochemical properties and autogenous healing performance of ternary blended binder composed of ordinary Portland cement (OPC), blast furnace slag (BFS), and calcium sulfoaluminate (CSA) clinker. Ternary blended binders with various contents of OPC-BFS-CSA clinker were prepared, and their physicochemical properties and autogenous healing performances were examined using various analytical techniques and visually observed using a microscope. The obtained results indicated that increase in the BFS content accompanied the increased the amount of unreacted BFS even after 28 days of curing and had a positive effect on the autogenous healing performance due to its latent hydration. However, replacing the CSA clinker did not increase the autogenous healing performance owing to an insufficient sulfate source for the formation of ettringite. The main precipitates around the cracks were calcite, C-S-H. Other hydration products such as portlandite, monosulfate, and ettringite, which were not found in the Raman and scanning electron microscope analyses.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.