• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.1
• /
• pp.94-100
• /
• 2008

Noise barriers are being used more often to solve problems of noise pollution from traffic noise. Several types of noise barriers are being installed to increase the cost-effectiveness of noise barrier installation. In this study, the insertion loss is analyzed to evaluate the effectiveness of the noise barrier by using the BEM. In order to check the validity of the BEM, the BEM and Lam's theoretical analysis are compared with measurement, which is performed in the anechoic chamber for the 1/10 scale-down model, and good agreements are obtained. By using the two dimensional boundary element method, the insertion loss is calculated and analyzed for several typical noise barriers such as the vertical barrier, the barrier with an oblique edge on top, the T-shaped barrier and the barrier with interference device on top. With these analyses, it is possible to design more cost-effective noise barriers appropriate for a particular area.

• Journal of KSNVE
• /
• v.10 no.3
• /
• pp.444-450
• /
• 2000

Wheel-rail noise is normally classified into three catagories : rolling impact and squeal noise. In this paper rolling noise caused by the irregularity between a wheel and a rail is analysed as follows: The irregularity between the wheel and the rail is assumed as linear superposition of sinusoidal profiles. Wheel-rail contact stiffness is linearized by using Hertzian contact theory and then contact force between the wheel and the rail is calculated. vibration of the rail and the wheel is calculated theoretically by receptance method or FEM depending on the geometry of the wheel or the rail for the frequency range of 100-500 Hz important for noise generation. The radiation noise caused by those vibration response is computed by BEM To verify this analysis tools rolling noise is calculated by proposed analysis steps using typical roughness data and these results are compared with experimental rolling noise data. This analysis tools show reasonable results and finally used for the prediction of the Korean high speed train rolling noise.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.1
• /
• pp.22-37
• /
• 2016

This article investigates numerical modeling of surface piercing propeller (SPP) in unsteady open water condition using boundary element method. The home code based on BEM has been developed for the prediction of propeller performance, unsteady ventilation pattern and cross flow effect on partially submerged propellers. To achieve accurate results and correct behavior extraction of the ventilation zone, finely mesh has generated around the propeller and especially in the situation intersection of propeller with the free surface. Hydrodynamic coefficients and ventilation pattern on key blade of SPP are calculated in the different advance coefficients. The values obtained from this numerical simulation are plotted and the results are compared with experiments data and ventilation observations. The predicted ventilated open water performances of the SPP as well as ventilation pattern are in good agreement with experimental data. Finally, the results of the BEM code/experiment comparisons are discussed.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.763-766
• /
• 2002

A BEM is highly efficient method in the sense of economic computation. However, boundary integration is not easy for the complex and moving surface e.g. in a rotating blade. Thus, Kirchhoff surface is designed in an effort to overcome the difficulty resulting from complex boundary conditions. A Kirchhoff surface is a fictitious surface which envelopes acoustic sources of main concern. Acoustic sources may be distributed on each Kirchhoff surface element depending on its acoustic characteristics. In this study, an axial fan is assumed to have loading noise as a dominant source. Dipole sources can be computed based on the FW-H equation. Acoustic field is then computed by changing Kirchhoff surface on which near-field is implemented, to analyze the effect of Kirchhoff surface on it.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.346-350
• /
• 2000

In scroll compressors, there are two major noise sources. Sturctural path: excitation of the compressor housing by unbalance forces and forces generated by compression cycle. Gas cavity path: excitation of top cap by discharge gas pulsation. In this study, in order to analyze the radiated noise generated by the discharge gas pulsation, FEM/BEM model of the top cap is established. Measured pressure of discharge pulsation is introduced in the FEM model as the excitation and vibration response is calculated. Radiated sound pressure is then obtained by BEM method based on this vibration response. Results are compared with the measured data. It is shown that the trend of the noise radiation can be predicted in this approadch.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.434-439
• /
• 2000

In this paper, in order to study the geometric factor effect of a circular hole near a crack tip in a semi-infinite plate, the Dimensionless Stress Intensity Factor, $F(=\frac K {\sigma {\sqrt{\pi a}}})$ is analyzed at the crack tip using a two Dimensional Boundary Element Method (BEM) program which is known as superior in Fracture Mechanics. Kelvin's solution was used as a fundamental solution in BEM analysis and displacement extrapolation method was used to determine Stress Intensity Factor.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.6
• /
• pp.650-655
• /
• 2011

Analysis of two-dimensional Rayleigh wave scattering pattern by a surface defect is studied through modified boundary element method. BEM proposed in this paper has special treatment at each end of boundary which should have the Rayleigh wave go away without any generation of virtual reflections. It is shown that treatment for truncated boundary which is used to model two-dimensional Rayleigh waves' behavior in an elastic half-space is successfully implemented. To check numerical results' accuracy, time domain IFFT signal of the displacements is presented. Improvement on getting rid of unwanted influence of truncated boundary induced by 2-D Rayleigh waves on a flat surface of an elastic half-infinite medium is shown. As a final goal, the numerical results of Rayleigh wave scattering trend are plotted and they are compared with theoretical curves to prove its accuracy.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.89-93
• /
• 2004

To numerically construct the sound fields by a plenum fan mostly found in Air-Handling Unit (AHU), the Kirchhoff-BEM approach was applied to the near-field data of a turbo fan. The scattering effects were found to be significant by the plenum box structure for high-frequency components of source. The directivity petterns and sound pressure levels were also dependent upon the helmholts number which must be considered of the design stage for sound reduction program.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.7
• /
• pp.457-461
• /
• 2000

The finite element method (FEM) is suitable for the analysis of a complicated region that includes nonlinear materials, whereas the boundary element method (BEM) is naturally effective for analyzing a very large region with linear characteristics. Therefore, considering the advantages in both methods, a novel algorithm for the alternate application of the FEM and BEM to magnetic field problems with the open boundary is presented. This approach avoids the disadvantages of the typical numerical methods with the open boundary problem such as a great number of unknown values for the FEM and non-symmetric matrix for the Hybrid FE-BE method. The solution of the overall problems is obtained by iterative calculations accompanied with the new acceleration method.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.130-132
• /
• 1999

The finite element method (FEM) is suitable for the analysis of a complicated region that includes nonlinear materials, whereas the boundary element method (BEM) is naturally effective for analyzing a very large region with linear characteristics. Therefore, considering the advantages in both methods, a novel algorithm for the alternate application of the FEM and BEM to magnetic field problems with the open boundary is presented. This approach avoids the disadvantages of the typical numerical methods with the open boundary problem such as a great number of unknown values for the FEM and non-symmetric matrix for the Hybrid FE-BE method. The solution of the overall problems is obtained by iterative calculations accompanied with the new acceleration method.