• Applied Chemistry for Engineering
• /
• v.31 no.6
• /
• pp.607-611
• /
• 2020

In this research, we synthesized Au/TiO2/graphene composites using ionic surfactants for the exfoliation of graphite layers, directly. In the graphene composite, TiO2 with thin nanosheet shapes was distributed on the graphene surface and Au nanoparticles with less than 10 nm sizes were evenly distributed on the surface of the TiO2 nanosheets. The Au/TiO2/graphene composite was then applied to the photodegradation of various dyes such as methylene blue, methylene orange and rhodamine 6G, and B. Among them, the methylene blue showed the most excellent photodegradation activity (91.6%) while the rhodamine B exhibited 31.0%.

• Journal of the Korean Ceramic Society
• /
• v.36 no.7
• /
• pp.767-772
• /
• 1999

The effect of B2O3 addition on the sintering behavior dielectric and ferroelectric properties of Ba0.7Sr0.3TiO3 ceramics were investigated. The sample with 0.5wt% B2O3 was sintered under 115$0^{\circ}C$. The dielectric and ferroelectric properties of BST with 0.5wt% B2O3 was as good as BST without B2O3 sintered at 135$0^{\circ}C$ and its dielectric loss was even better When B2O3 was added over 1.0wt% the overdoped B2O3 remained in the specimens and formed a second phase which degraded the sintering behaivor dielectric properties of BST.

• Journal of the Korean Ceramic Society
• /
• v.42 no.9 s.280
• /
• pp.607-612
• /
• 2005

The effect of MgO diluents in combustion synthesis of $TiB_2$ nano particles was investigated. The reaction $TiO_2\;+\;B_2O_3\;+\;xMg\;{\rightarrow}\;TiB_2\;+\;5MgO$ was used to synthesize $TiB_2$ nano particles. The combustion velocity was measured to examine the relation between the reaction temperature and the morphologies of particles. The diluent MgO did not react with the reactants and played a role to decrease combustion temperature. As the MgO diluents contents increased, the particles with the smaller size and the narrower size distribution were synthesized. At the condition of 6 mole of MgO, the combustion wave velocity was about 5 cm/see and the synthesized particles showed the size of 60 nm with narrow size distribution.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2003.11b
• /
• pp.295-299
• /
• 2003

1. 고정화 $TiO_2$의 경우도 분말을 이용한 것과 같이 최적 광촉매 투입량이 나타났으며, 최적 투입량은 33.8 g/L이었고, 분말 $TiO_2$를 이용한 경우보다 빠른 초기반응속도를 보였으며, 최종반응시간도 빠른 것으로 나타났다. 2. 수용액에서 빠른 초기 제거속도의 1차적인 기작은 고정화 $TiO_2$ 표면으로의 흡착 때문이었으며, 빠른 흡착으로 인해 수용액 중의 RhB 농도가 빠르게 감소하여 광 투과율이 증가하므로 전체 반옹속도가 빠른 것으로 사료되었다. 3. 고정화 $TiO_2$를 이용한 유동층 반응기의 경우 최적 공기 공급량은 의한 Rhodamine B의 초기 제거속도는 분말보다 빠르지만 전체적인 제거시간은 흡착된 Rhodamine B의 분해 때문에 분말 $TiO_2$보다 느린 것으로 나타났다.

• Korean Journal of Materials Research
• /
• v.2 no.3
• /
• pp.207-212
• /
• 1992

The defect structure of calcium titanates with CaO excess or $TiO_2$ excess was studied by measuring electrical conductivities as a funcition of oxygen partial pressure at $85O^{\circ}C$ to $1050^{\circ}C$. Execess CaO may divide itself equally between A and B sites, resulting in $Ca_{Ti}$" and Vo", while excess $TiO_2$ form $V_{Ca}$" and Vo". The equilibrium electrical conductivity data indicate that the solubilities of CaO and $TiO_2$ in $CaTiO_3$ are 5000ppm and 2000ppm, respectively. Oxygen vacancies contributed to the ionic conduction which flatten the conductivity minima and did not make any defect association with oppositely charged defects.ely charged defects.

• The Korean Journal of Ceramics
• /
• v.5 no.4
• /
• pp.324-330
• /
• 1999

$Si_3N_4$-$TiB_2$ with 2 wt% $Al_2O_3$ and 4 wt% $Y_2O_3$ additives was hot pressed in a flowing $N_2$ environment with varying $TiB_2$ content from 10 to 50 vol%. Variations of mechanical (hardness, fracture toughness, and flexual strength), and tribological properties as a function of $TiB_2$ content were investigated. As the content of $TiB_2$ increased, relative density decreased due to the chemical reaction of $TiB_2$in $N_2$ environment. The reduction of density causes mechanical properties to be degraded with an increase of $TiB_2$ in $Si_3N_4$. Tribological properties were dependent of microstructure as well as mechanical properties, however, they were degraded strongly by the chemical reaction of $Si_3N_4$-$TiB_2$ during hot pressing in $N_2$ environment. SEM and TEM observations, and X-ray diffraction analysis that the chemical reaction products at the interface are TiCN, Si, and $SiO_2$. Also, the comparison of XRD patterns of the $Si_3N_4$-40 vol% $TiB_2$ composites hot pressed at $1,750^{\circ}C$ for 1 hour between in $N_2$ and in Ar gas was made. The XRD peaks of Si and $SiO_2$ were not found in Ar, but still a weak peak of TiCN was presented.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.313-318
• /
• 2001

The sliding wear behavior of Plasma-Sprayed Al$_2$O$_3$-TiO$_2$ Coating against Cemented Carbide were Investigated using a pin on disk type tester. The experiment was conducted using Al$_2$O$_3$-TiO$_2$ Coaling as pin material and Cemented Carbide as disk material and different operating conditions, at room temperature under a dry conditions. The results showed that the type B(250kw power) appeared average wear rate Is lowed than type A(80kw power). The specific wear rate of Specimen A1 Increased with normal load. But The specific wear rate of Specimen B1 decreased with normal load. Average wear rate of specimen A3, B3 are lowed than other but the sliding wear mechanism of edge were rough.

• Journal of the Korean Chemical Society
• /
• v.46 no.3
• /
• pp.179-186
• /
• 2002

A molecular orbital analysis based on the extended Huckel calculations has been carried out to study the OH bond activation of water on the $TiO_2$(110) surface. $H_2O$ binds with its axis perpendicular to the surfac on top of the five-coordinate $Ti^{4+}$ atom via its $3a_1$ orbital. In this bonding situation, the two-coordinated bridging $O^{2-}$ atom ($O_b$, basic site) on $TiO_2$(110) is too distant from an H atom of water to form hydrogen-bondig interactions with water that facilitate O-H bond cleavage. It has been elucidated that the O-H bond is appreciably weakened when the water molecule is tilted to give a hydrogen bond with the $O_b$ atom. This mechanism includes mutual transfer of electron density from the $3a_1$ orbital of the water molecule to the $Ti^{4+} 3d_{z2}$ orbital and from the $O_b$ P orbitals to the $2b_1$ of the adsorbed water molecule This should result in lengthening of the O-H bond in the surface complex and the subsequent dissociation into the fragments OH and H.

• Journal of Environmental Science International
• /
• v.13 no.10
• /
• pp.921-928
• /
• 2004

The photocatalytic decolorization of Rhodamine B (RhB) was studied using immobilized $TiO_2$ and fluidized bed reactor. Immobilized $TiO_2$(length: 1$\~$2 mm, width: 1$\~$3 mm, thickness: 0.5$\~$2 mm) onto silicone sealant was employed as the photocatalyst and a 30 W germicidal lamp was used as the light source and the reactor volume was 4.8 L. The effects of parameters such as the amounts of photocatalyst, initial concentration, initial pH, superficial velocity, $H_2O_2$ and anion additives. ($NO_3^{-},\;SO_4^{2-},\;Cl^{-},\;CO_3^{2-}$) The results showed that the optimum dosage of the immobilized $TiO_2$ were 87.0 g/L. Initial removal rate of RhB of the immobilized $TiO_2$ was 1.5 times higher than that of the powder $TiO_2$ because of the adsorption onto the surface of immobilized $TiO_2$ In the conditions of acidic pH, initial reaction rate was increased slowly and reaction time was shorted. The effect of anion type on the reaction rate was not much.

• Journal of the Korean Ceramic Society
• /
• v.40 no.1
• /
• pp.81-86
• /
• 2003

Microwave dielectric properties have been investigated in the$(1-x)CaTiO_3-xYAlO_3$ (x=0.1~1.0) solid solution system. The mixtures of $CaTiO_3$ and $YalO_3$using solid state method were sintered at various temperatures. Their dielectric constants and related temperature coefficients were strongly depend on the composition of the solid solution. The optimum properties were recorded as for ${\varepsilon}_r=47,$ $Q{\times}f_0$=35000 and ${\tau}_f=+11ppm/^{\circ}C$ without sintering agent. Even at $1200^{\circ}C$ full densification has been achieved with addition of $CaB_2O_4$ in the $0.75CaTiO_3-0.25YalO_3$ composition. The sample of $0.3 wt%-CaB_2O_4$ added $ 0.75CaTiO_3-0.25YalO_3$ sintered at $1300^{\circ}C$ for 3 h showed optimum microwave dielectric properties of ${\varepsilon}_r=47$, $Q{\time}f_0=37000$ and ${\tau}_f=+17ppm/^{\circ}C$, which demonstrates the promising candidates for microwave dielectric materials covering 5~7 GHz range.