• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.6
• /
• pp.677-686
• /
• 2006

This study was the effectiveness of two downflow BAF(Biological Aerated Filter) systems at conventional water treatment system. A BAF reactor placed in front of coagulation and sedimentation tanks(Mode A) and after coagulation and sedimentation tanks(Mode B) that were compared in terms of removal of suspended particles, organic matters, and ammonia nitrogen. The suspended particles removal efficiency was over 80% for both Mode A and B, although Mode A gave slightly better results. $BOD_5$ removal and nitrification efficiencies were more than 90% for both reactor. The organic matter and ammonia removals were also superior in the Mode A. The biofilm thickness and biomass increased as increment of EBCT and the upper part of reactor more about 30% than lower part. The specific oxygen uptake rate(SOUR) was higher the upper part of reactor and Mode A than the lower part of reactor and Mode B. A cost analysis showed that the Mode A system was more cost effectiveness. It could save the coagulant dose by about 67% and the chlorine demand by about 95%. The ideal place to put the BAF reactor was in front of the coagulation/sedimentation process.

• Journal of the Optical Society of Korea
• /
• v.13 no.3
• /
• pp.349-353
• /
• 2009

We propose a simple in-line variable optical attenuator (VOA) based on the bending effect of tapered single mode fibers. The influence of the taper structure and the reflective index of the external medium surrounding the taper region on the bending loss of the tapered fiber have been investigated experimentally. An attenuation range exceeding 35 dB and a very low excess loss of < 0.2 dB at 1550 nm were achieved. The measured polarization dependent loss of the present VOA at the attenuation level of 10 dB, 20 dB, and 30 dB were 0.1 dB, 0.2 dB, and 0.5 dB, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.11
• /
• pp.1582-1590
• /
• 1998

Combustion-driven oscillations in a surface burner have been investigated to clarify their characteristics. A model combustor is made and the oscillation frequencies are measured for various dimensions of the combustor. It is found that there are two modes of oscillations; one is the 'acoustic mode' at high frequencies, associated with the acoustic mode of the combustion system and the other is the 'combustion mode' at low frequencies around 100 Hz, associated with the instability of the flame. Acoustic mode is excited when the surface burner is placed where the phase of particle velocity leads that of acoustic pressure by $90^{\circ}$, for all the combustion conditions. Combustion mode is driven at high combustion rate by the lift of unstable flame near the lower limit of the combustible equivalence ratio. Combustion mode is greatly influenced by the inlet temperature of the premixed gas. When the inlet temperature is very high, the combustion mode does not occur.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.7
• /
• pp.374-379
• /
• 2006

The switch mode power supply is a source of EMI with other equipment as well as with its own proper operation because of rapid changes in voltages and currents within a switching converter. The EMI is transmitted in two forms: radiated and conducted. Conducted noise consists of two categories known as the differential mode and the common mode. Common mode noise current is a major source of EMI in the switch mode Power supply. Recently, a current balancing technique has been studied to reduce the common mode noise. This paper investigates the reduction of common mode noise according to a node expansion of the switch mode power supply which is based on a current balancing technique. In this paper, seven PCB patterns of the forward converter are manufactured and experimented.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.12
• /
• pp.43-49
• /
• 2004

In this paper, we have designed a mode size converter to reduce coupling loss between super-high delta silica optical waveguides and single mode fibers. The new mode size converter has three design aspects; periodically segmented taper waveguide for minimal size, lateral taper waveguide for simple fabrication, and surrounding trenches to improve coupling loss. In the optimal mode size converter design, coupling loss is 0.33dB/point without trenches and 0.2dB/point with trenches.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.127-132
• /
• 2006

This paper presents a dual-mode amplifier which operates as amplifier or frequency multiplier according to the input frequency. It satisfies the 802.11a/b/g frequency band of wireless LAN standard. A conventional dual-band wireless LAN transmitter consists of the separating power amplifiers operating at each frequency band, but the proposed dual-mode amplifier operates as an amplifier for the 802.11b/g signal and as a frequency multiplier for the 802.11a signal according to each LAN bias condition. The amplifier mode shows the gain of 13dB, the PldB of 17dBm and second harmonic suppression of below -37dBc. And the frequency-doubler mode shows the gain of 3.3dB, the output power of 7.3dBm and third harmonic suppression of below -50dBr.

• Journal of Astronomy and Space Sciences
• /
• v.27 no.2
• /
• pp.107-116
• /
• 2010

We developed the playback control software for a high-speed playback system which is a component of the Korea-Japan Joint VLBI Correlator (KJJVC). The Mark5B system, which is a recorder and playback system used in the Korean VLBI Network (KVN), has two kinds of operation mode. That is to say, the station unit (SU) mode, which is for the present Mark4 system, and the VSI mode, which is for the new VLBI standard interface (VSI) system. The software for SU is already developed and widely used in the Mark4 type VLBI system, but the software for VSI has only been developed for recording. The new VLBI system is designed with a VSI interface for compatibility between different systems. Therefore, the playback control software development of the VSI mode is needed for KVN. In this work, we developed the playback control software of the Mark5B VSI mode. The developed playback control software consists of an application part for data playing back, a data input/output part for the VSI board, a module for the StreamStor RAID board, and a user interface part, including an observation time control part. To verify the performance of developed playback control software, the playback and correlation experiments were performed using the real observation data in Mark5B system and KJJVC. To check the observation time control, the data playback experiment was performed between the Mark5B and Raw VLBI Data Buffer (RVDB) systems. Through the experimental results, we confirmed the performance of developed playback control software in the Mark5B VSI mode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.664-667
• /
• 2001

A flat-type L$_1$-B$_{8}$ Mode Ultrasonic motor(USM) uses longitudinal-bending multi-mode vibrator which is constructed with the metal-piezoceramic composite thin plate vibrator. Especially, the characteristics of vibrating displacement of the vibrator are important for the fabrication of USM. So, in this study, we tried to analyze them by the FEM(finite element method) simulation program. ANSYS 5.6 we used is a finite element software enabling the analysis of 2 or 3 dimensional structure of piezoelectric materials. Using this made us analyzing the resonance frequency and calculating displacement of vibrator and then the position of the projection.n.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.343-351
• /
• 2008

In this paper, a spiral shaped common mode filter(CMF) embedded in a flexible printed circuit board(FPCB) is proposed for a multi-function cable. The CMF embedded in a FPC cable presents a new concept as a multi-function cable by the common mode rejection characteristics without a surface mounted device(SMD) CMF. The embedded CMF has a wideband common mode rejection bandwidth and an enhanced differential mode characteristics compared to conventional CMFs that use a magnetic material such as a ferrite of high loss. The proposed CMF of 3 turn inductors has a common mode rejection bandwidth from 0.4 GHz to 3.12 GHz and has 1.95 dB at 3 GHz, 6.97 dB at 8 GHz improvements of a differential mode insertion loss compared to the commercial LTCC(Low Temperature Co-fire Ceramics) CMFs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.4
• /
• pp.447-452
• /
• 2011

In this paper, we present a compact triple-mode resonator. The resonator itself can provide three transmission poles and one transmission zero. The resonance condition of each mode is analyzed theoretically, and the transmission zero is generated by open stub. Using this proposed resonator, a compact three pole bandpass filter for 2.4 GHz WLAN application with one transmission zero is designed and fabricated. The fabricated triple-mode filter shows 3 dB bandwidth of 15.8 % with the center frequency 2.4 GHz and less then 1.17 dB in 2.4~2.5 GHz passband. The size of fabricated triple-mode filter including the feed lines is 15.9 mm${\times}$9.7 mm and very compact compared with previous reported triple-mode filter.