• Journal of Advanced Navigation Technology
• /
• v.21 no.4
• /
• pp.325-331
• /
• 2017

As a GPS stability problem arises, MLAT system is spotlighted as an alternative technology of ADS-B. MLAT system has a high position accuracy as much as ADS-B. Also, MLAT receives the mode A,C,S, and 1090ES(ADS-B) signals from the mounted aircraft transponder. MLAT receives signals from several receiver units and calculates aircraft positions. MLAT has ADS-B level positioning accurarcy using GPS and can calculate the position information with objects independently. According to global environment changes, Local area multiltilateration(LAM) surveillance system is under development for moving vehicles and aircraft detection in airport. These are still under testing in Tae-an Airfield. In the paper, we analyzed the performance by comparing the calculated position data from MLAT to RTK. In order to confirm the position accuracy of MLAT and the deviation of position data between fixed target and moving target on the ground during the field test in Tae-an Airfield.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.957-963
• /
• 2005

This paper presents technique of wideband TIA for optical communication systems using TSMC 0.25 ${\mu}m$ CMOS RF-Mixed mode. In order to improve bandwidth characteristics of an TIA, we use active inductor shunt peaking to cascode and common-source configuration. The result shows the 37 mW and 45 mW power dissipation with 2.5 V bias and 61 dB$\Omega$ and 61.4 dB$\Omega$ transimpedance gain. And the -3 dB bandwidth of the TIA is enhanced from 0.8 GHz to 1.45 GHz in cascode and 0.61 GHz to 0.9 GHz in common-source. And the input noise current density is $5 pA/\sqrt{Hz}$ and $4.5 pA/\sqrt{Hz}$, and -10 dB out put return loss is obtained in 1.45 GHz. The total size of the chip is $1150{\times}940{\mu}m^2$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.900-905
• /
• 2009

A common drain feedback CMOS wideband LNA with current bleeding and input inductive series-peaking techniques is presented in this paper. DC coupling is adopted between cascode and feedback amplifiers, so that the gain and NF of the LNA can be dynamically controlled by adjusting the bleeding current. The fabricated LNA shows the bandwidth of 2.5 GHz. The high gain mode shows 17.5 dB gain with $1.7{\sim}2.8\;dB$ NF and consumes 27 mW power and the low gain mode has 14 dB gain with $2.7{\sim}4.0\;dB$ NF and dissipates 1.8 mW from 1.8 V supply.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.9
• /
• pp.1027-1034
• /
• 2014

We present the Low Power Broadband Low noise amplifier(LNA) that can be applied a whole bandwidth from 3G to 4G LTE. This multi input LNA was designed to steadily amplify through a multi input method regardless the size of the input signal and operate on a wide range of frequency band from a standard 3G CDMA band 1.2GHz to LTE band 2.5GHz. The designed LNA consumes an average of 6mA on a 1.2V power supply and this was affirmed using computer simulation tests. The amplification which was corresponded to the lowest input signal is at a maximum of 20dB and was able to obtain the minimum value of the gain of -10dB. The Noise figure is less than 3dB at a High-gain mode and is less than 15dB at a Low-gain mode.

• Journal of Korea Foundry Society
• /
• v.23 no.2
• /
• pp.77-85
• /
• 2003

Some alloying elements such as Cr, B, Ti and Si were added individually or as a mixture to Fe-30 at.%Al alloys. The alloys were melted using an arc furnace and then heat-treated for homogenization at 1000$^{\circ}C$ for 7 days and followed by rolling at 1000$^{\circ}C$. The alloying elements on rolling characteristics were investigated by the microstructures and fracture mode before and after rolling. The microstructures before rolling showed that all of the alloys had equiaxed grains. On the other hand, the microstructures of rolling plane as well as its perpendicular plane became elongated after rolling. The alloys such as Fe-30Al, Fe-30Al-3Ti, Fe-30Al-0.5B, Fe-30Al-5Cr and Fe-30Al-3Ti-0.5B revealed better rolling behaviour from the point that intergranular and cleavage fractures were not fundamentally occurred. But the addition of 5Ti or 3Si to Fe-Al alloys had detrimental effects. The Ti-added alloy system such as Fe-30Al-5Ti, Fe-30Al-5Ti-5Cr, Fe-30Al-3Ti-5Cr and Fe-30Al-5Ti-0.5B were cracked through grain and showed cleavage fracture. The Si-added alloy system such as Fe-30Al-5Si, Fe-27Al-3Si and Fe-27Al-5Cr-3Si were cracked along the grain boundary and showed intergranular fracture. $DO_3{\leftrightarrow}B_2$ transition temperature of Fe-30at.%Al alloy was 520$^{\circ}C$, whereas the addition of 3Ti and 3Ti+0.5B comparably increased the temperature to 797 and 773$^{\circ}C$, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.1
• /
• pp.68-74
• /
• 2000

Experimental investigation on flame spread along suspended droplet arrays have been conducted with various droplet spacings and ambient air velocities. Especially, an opposed air stream is introduced to simulate fundamental flame spread behaviors in spray combustion. High-speed chemiluminescence imaging technique of OH radicals has been adopted to measure flame spread rates and to observe various flame spread behaviors. The fuel used is n-Decane and the air velocity varies from 0 to 17cm/s. The pattern of flame spread is grouped into two: a continuous mode and an intermittent one. It is found that there exists droplet spcings, above which flame spread does not occur. The increase of ambient air velocity causes the limit droplet spacing of flame spread to become small due to the increase of apparent flame stretch. As the ambient air velocity decreases, flame spread rate increases and then decreases after taking a maximum flame spread rate. This suggests that there exists a moderate air flowing to give a maximum flame spread rate due to enhanced chemical reaction by the increase of oxidizer concentration.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.32-33
• /
• 2009

We propose viewing angle switchable liquid crystal display(LCD) associated with fringe-field switching (FFS) mode with high aperture ratio characteristic. This device is composed of R(red), G(green), B(blue), pixel and W(white) pixel in which R,G,B pixel shows image and white pixel for both viewing angle control and image. Conventional viewing angle controllable liquid crystal display has not transmittance because the liquid crystal only tilts up without rotates in viewing angle control region. In this paper, we suggested that the device has high transmittance characteristic because the LC directors are rotated in which viewing angle control region are generated fringe electric field.

• Journal of Internet Computing and Services
• /
• v.12 no.3
• /
• pp.111-117
• /
• 2011

In this paper, the BER(Bit Error Rate) performance of a DVB-T2(Second Generation Digital Terrestrial Television Broadcasting System) in MISO(Multiple Input Single Output) transmission mode is evaluated by the computer simulation. In the DVB-T2 receiver, an IDD(Iterative Demapping and Decoder) technique is employed that exchanges extrinsic information between the demapper and the LDPC decoder. Simulation results show that the IDD-based DVB-T2 receiver in MISO transmission mode provides 2dB gain at BER of $10^{-4}$ but suffer from the frequency offsets between transmit antennas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.684-688
• /
• 2001

The structural, piezoelectric and dynamic range characteristics of modified PbTi $O_3$ceramics were investigated as a function of Mn $O_2$addition. With the increase of Mn $O_2$addition, Curie temperature was decreased. As the increase of Mn $O_2$addition, mechanical quality factor ( $Q_{mt3}$) in the third over tone thickness mode was increased. Dynamic range in the third over tone thickness mode was also increased with the increase of Mn $O_2$addition. The composition ceramics added to 0.075wt% Mn $O_2$showed the best properties for SMD type resonator using third over tone thickness vibration in terms of high Curie temperature more than 31$0^{\circ}C$ and dynamic range of 49.38dB.B.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.8
• /
• pp.457-466
• /
• 2002

The speed and position control of SRM(Switched Reluctance Motor) needs the encoder or resolver to obtain the rotor position information. These position sensors can be affected by the EMI, dusty, and high temperature surroundings. Therefore the speed and position sensorless control has been studied widely In this paper, the binary observer of the SRM which has two feedback compensation loops to control the speed of SRM is proposed. One loop reduces the estimation error like the sliding mode observer, and the other removes the estimation error chattering occurred in the sliding mode observer. This observer is constructed on the basis of variable structure control theory and has the inertial term to exclude the chattering. This method has a good estimation performance in spite of nonlinear modeling of SRM. The advantages of the proposed method are verified experimentally.