• Journal of Astronomy and Space Sciences
• /
• v.14 no.2
• /
• pp.386-394
• /
• 1997

In this study, a few of the modeling methods for flexible spacecraft were introduced and adopted to the modeling of a 3-axes stabilization satellite. The generated model was put into pre-built rigid body attitude control loop. A Lumped Parameter Model(Global Mode Model: GMM) was recommended for the absence of the Finite Element Method(FEM) model. Finally, GMM was compared with FEM in terms of designing a control filter. A 1st-order filter was designed to meet requirements of the controller since the new flexible model was applied, and that filter was added to motor controller and axis controller. MATLAB/Simulink was used as a tool for design and simulation of the control loop and filter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.803-808
• /
• 2006

This paper was a study about noise reduction through flow stabilization in duel using experimental method and numerical analysis at the same time. To determine the fan's type three kinds of fans(axial fan, centrifugal fan, and axial fan with centrifugal type) was examined to investigate the suitability for duct. As a result, under the equal number of rotation 2000 RPM, performance of an axial fan with centrifugal type was the most superior by 55dBA at 4.3CMM among other fans. After this, analyzed the results of the numerical analysis to find out the optimum design of pitch angle such as $0^{\circ},\;10^{\circ},\;15^{\circ}\;and\;20^{\circ}$. The intensity of turbulence was low when pitch angle was $15^{\circ}$ and air volume became peak by 5.08 CMM. It was observed that axis component of velocity increased gradually when pitch angle increased from $0^{\circ}\;to\;20^{\circ}$. Finally, designed the shapes of D/S(Down Stream) in duct that agreed inlet angle($\delta$) of stationary blades with pitch angle($\beta$) of axial fan with centrifugal type and derived flow to duct medial, and changed the shape of motor-mount to reduce occurance of unstable vortex in tip of impeller, and embodied noise reduction and improvement of air flow rate through flow stabilization.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.2
• /
• pp.129-136
• /
• 2014

Target-tracking systems are important for carrying out effective surveillance missions using mobile surveillance robots. In this paper, we propose a target-tracking algorithm using camera image data for a three-axis mobile surveillance robot and carry out an actual hardware test for verifying the proposed algorithm. The heading direction vector of a camera system is deduced from the position error between the viewfinder center and the object center in a camera image. The position error is obtained using the CAMShift(Continuously Adaptive Mean Shift) algorithm, an image processing technique. The performance test of an actual three-axis mobile surveillance robot was carried out for verifying the proposed target-tracking algorithm in a real environment.

• Journal of the Society of Naval Architects of Korea
• /
• v.52 no.6
• /
• pp.452-459
• /
• 2015

It is important to use bench test results in the design process of anti-rolling tanks. Traditional bench tester is usually designed to perform only roll motions about a fixed axis and relatively small so that the viscous effects may not be neglected. Novel bench tester which could adjust the motion center to realize the coupled motion of sway and roll has been devised and manufactured therefore, large scaled bench tester could be utilized for designing the passive anti-rolling tanks. The time history of the reference signal from the rotation sensor of the bench tester have been recorded and processed to determine the phase angle to derive the Response Amplitude Operator(RAO) of the stabilized ship. The breadth of ART tank model should be large up to 2 m to diminish viscous scale effect and the vertical position of the tank can be varied with the ship's center of motion. The periods and the amplitude of roll motion can be varied from 1.5 sec to 5 sec and up to ±20°, respectively. The components of the tester was expressed in three dimensional digital mockup (DMU) and assembled together in the CAD space. The final configuration of the bench tester has been determined by confirming the smooth operation of the moving parts without interference through the animation in CAD space. New analytic logic are introduced for the determination of hydrodynamic moment and phase difference due to fluid motion in ART and verified through the test. The developed bench tester is believed to be effective and accurate for the verification of stabilization effect of ART taking into the consideration of the sway effect in the design stage.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.8
• /
• pp.16-21
• /
• 2012

The gyro sensor that made by MEMS process is generated an accumulated error(drift) and escape the zero angle following during calculation of rotate angle. This study propose BACF(Boot Angle Compensation Filter) algorithm for prevent escape zero angle and DCF algorithm for remove accumulated error. DCF algorithm is designed for acquire accurate turn of ratio by remove offset and noise components. BACF algorithm is obtained average offset that removed noise components by recursively calculate. Experimental environment, two-axis gyro sensor and mobile OIS camera mounted control board and 5Hz oscillation of ${\pm}0.5^{\circ}$ for the experiments were carried out. BACF and DCF algorithm is applied and the resulting accumulated error did not occur and exactly zero angle following results were made.

• Journal of the Korean Institute of Rural Architecture
• /
• v.24 no.4
• /
• pp.133-139
• /
• 2022

This study deals with the formation of Jongyeonbangjeok's Gwangju Factory in the 1930's to 80's, and the findings are shown below: In the period of formation, the factory was rectangular-shaped from north to south, and the structure was located at the center of the site, and in the east of it, there was a dormitory connected from south to north. The building was arranged with an open area on the south. In the east of the site where company houses were located, same-sized structures were arranged along the axis.In the period of change, the factory was restored about the damage from the Korean War, and it went through the process of division into two companies. As a result, the factory in the center of the site was divided into left and right ones, and the dormitory and the group of company houses were, too, divided into two, so division was made largely into southern and northern parts. In the period of stabilization, along with factory extension in each of the companies, welfare for factory workers was expanded by building more houses or opening sport facilities. After the 1980's, too, the existing factories were either extended or remodeled according to the induction of equipment, and some showed changes in their functions due to a fire or such.

• Journal of Astronomy and Space Sciences
• /
• v.20 no.4
• /
• pp.339-350
• /
• 2003

Engineering qualification model payload for a communications and broadcasting satellite(CBS) was developed by ETRI from May, 2000 to April, 2003. For. the purpose of functional test and verification of the payload, a real-time hardware-in-the-loop(HITL) CBS simulator(CBSSIM) was also developed. We assumed that the spacecraft platform for the CBSSIM is a geostationary communication satellite using momentum bias three-axis stabilization control technique based on Koreasat. The payload hardware is combined with CBSSIM via Power, Command and Telemetry System(PCTS) of Electrical Ground Support Equipment(EGSE). CBSSIM is connected with PCTS by TCP/IP and the payload is combined with PCTS by MIL-STD-1553B protocol and DC harness. This simulator runs under the PC-based simulation environment with Windows 2000 operating system. The satellite commands from the operators are transferred to the payload or bus subsystem models through the real-time process block in the simulator. Design requirements of the CBSSIM are to operate in real-time and generate telemetry. CBSSIM provides various graphic monitoring interfaces and control functions and supports both pre-launch and after-launch of a communication satellite system. In this paper, the HITL simulator system including CBSSIM, communications payload and PCTS as the medium of interface between CBSSIM and communications payload will be described in aspects of the system architecture, spacecraft models, and simulator operation environment.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.5
• /
• pp.373-381
• /
• 2021

This paper details the result of flight experiment that examines performance of roll angle estimation algorithm of slowly rolling munition taking time delay of measurement into account when measurement comes in delayed fashion. As the measurement is passed through low pass filter for numerical stabilization and de-noising purpose which induces time delay, we design augmented state Kalman filter that incorporates distribution models of stochastic delay over time. Flight experiment was conducted to verify the algorithm at around 250m high AGL(Above Ground Level) conveying velocity of 28m/s from fixed-wing mother plane to the munition. Munition was made spun with respect to its roll axis using internal reaction wheel afterward. Numerical comparison of proposing method's roll estimation performance with that of commercial aerospace graded GPS/INS shows that proposed filter design can effectively compensate time delay of measurement.