• Journal of Welding and Joining
• /
• v.22 no.6
• /
• pp.50-56
• /
• 2004

MlAB(magnetically impelled arc butt) welding is a sort of pressure welding method by melting two pipe sections with high speed rotating arc and upsetting two pipes in the axial direction. The electro-magnetic force, the driving force of the arc rotation, is generated by interaction of arc current and magnetic field induced from the magnetic flux generator in the welding system. In this study, an openable coil system for the generation of magnetic flux and a 3-dimensional numerical model for analyzing the electro-magnetic field were proposed. Through the fundamental numerical analyses, a magnetic concentrator was adopted for smoothing the magnetic flux density distribution in the circumferential direction. And then a series of numerical analysis were performed for investigating the effect of system parameters on the magnetic flux density distribution in the interested welding area.. Numerical quantitative analyses showed that magnetic flux density distribution generated from the proposed coil system is mainly dependent on the exciting current in the coil and the position of coil or concentrator from the pipe outer surface. And the gap between pipe ends and arc current are also considered as important factors on arc rotating behavior.

• Journal of the Korean Chemical Society
• /
• v.24 no.2
• /
• pp.91-100
• /
• 1980

A formula for calculation of the magnetic moments for octahedral $[Ti(III)A_3B_3]$ type complexes with axial symmetry has been developed and the magnetic moments for these complexes are calculated, using the experimental values of the distortion parameters$({\delta})$, spin-orbit coupling constants and orbital reduction factors. The calculated magnetic moments for axially distorted octahedral $[Ti(III)A_3B_3]$ type complexes are in resonable agreement with the experimental valuest It is found that the calculated magnetic moments decrease as the extent of axial distortion increases and the orbital reduction factor decreases. A calculation method of the magnetic moments for octahedral $[Ti(III)A_3B_3]$ type complexes which are in a ligand field of lower than axial symmetry has also been developed and the structure of distorted octahedral $[Ti(III)A_3B_3]$ type complexes are discussed on the basis of the of the calculated magnetic moments.

• Journal of the Korean Magnetics Society
• /
• v.13 no.4
• /
• pp.182-186
• /
• 2003

A new axial pressing method using pulse magnetizing field was studied to improve the remanence of Nd-Fe-B sintered magnets. In order to make near-net shape green compacts of butterfly, disk, or coin magnets, conventional axial-type pressing has been normally used. However, compared to the transverse-type pressing, it is not possible to obtain higher remanence by this method because the magnetic alignment of powder begins to deteriorate when the density of green compacts increases over a critical value. On the other hand, we found that an axial pressing under pulse magnetizing field was very effective to increase the degree of magnetic alignment of powder, yielding remanences even higher than those obtained by the transverse pressing. In this study, it was revealed that appropriate tapping density and how to apply pulse magnetic held were important to improve the grain alignment and thus remanence of Nd-Fe-B sintered magnet.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.290-293
• /
• 2000

Low frequency(<100Hz) weak magnetic field(<20gauss) is applied axially to an inductively coupled oxygen plasma(ICP), and its plasma characteristics are monitored by OES(Optical Emission Spectroscopy) and Langmuir probe. It is found that periodic magnetic field enhances ashing rate by 25％ and improves its uniformity upto 4.5％ over 8" wafer. From electron energy distribution function, both low and high energy electrons are identified and relative abundancy is found to be controlled by the applied frequency. Moreover, it is observed that ionization and dissociation species are varied with applied frequency. We insert an aluminium baffle in the chamber to get better uniformity and less plasma damage.

• Journal of applied mathematics & informatics
• /
• v.12 no.1_2
• /
• pp.267-279
• /
• 2003

The present investigation deals with the application of Adomian's decomposition method to blood flow through a constricted artery in the presence of an external transverse magnetic field which is applied uniformly. The blood flowing through the tube is assumed to be Newtonian in character. The expressions for the two-term approximation to the solution of stream function, axial velocity component and wall shear stress are obtained in this analysis. The numerical solutions of the wall shear stress for different values of Reynold number and Hartmann number are shown graphically. The solution of this theoretical result for a particular Hart-mann number is compared with the integral method solution of Morgan and Young［17］.

• Journal of the Korean Magnetics Society
• /
• v.5 no.2
• /
• pp.99-102
• /
• 1995

When the low magnetic field is applied to the synunetry axis of the axial synunetric electric field gradient tensor of the quadrupolar nucleus in the crystal with nuclear spin, I=1, two split resonance frequencies are observed by the Zeeman effect on the nuclear quadrupole resonance. The applied magnetic field is proportional to the difference of the two resonance frequencies and this proportionality constant for the $^{14}N$ of ${(CH_{2})}_{6}N_{4}$ single crystal is 0.16 mT/kHz. The NQR spectrometer is interfaced with a personal computer from which the resonance signals are displayed and the value of magnetic field is obtained directly from the difference of the two resonance frequeocies. The lowestest measured magnetic field was 0.20 mT using this NQR technique.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.6
• /
• pp.42-48
• /
• 2011

Generally, the structure without the stator core Axial Field Permanent Magnet (AFPM) generator was simple and there was nearly no cogging toque. And because it had the wide driving rate area, it had been being mainly used in the small wind power generation system. However, AFPM generator with non-slotted stator can't generate high voltage at low wind speed due to long air-gap. It is the reason of output efficiency drop. Therefore, in this paper, the AFPM synchronous generator with internal rotor and dual slotted stators for the small wind turbine is studied, and deal with a cogging torque minimization through the determination of optimum pole-arc ratio.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.5
• /
• pp.96-100
• /
• 2007

Condenser lens and objective lens are used to demagnify the image of the crossover to the final spot size. In lens, electrons are focused by magnetic fields. This fields is fringing field. It is important in electron focusing. Electron focusing occurs the radial component field and axial component field. Radial component produces rotational force and axial component produces radial force. Radial force causes the electron's trajectory to curve toward the optic axis and corss it. Focal length decreases as the current of lens increases. In this paper, we use the focal length for desiging the hardware of lens current control and present the results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.11
• /
• pp.932-938
• /
• 2017

Particle-in-cell method which blends Eulerian grids and Lagrangian particle is utilized to solve simplified hall-effect thruster. Since this study individually tracks not only neutrons and ions but also electrons, message passing interface(mpi) scheme is adopted for parallel computer cluster. Helical movement of an electron cloud in constant magnetic field is validated comparing with an exact solution. A plasma in radial magnetic field and axial electric field in a reaction cylinder is established. Electrons do double helix movement and are well anchored in a cylinder. Ionization of neutrons by impact with high-speed electrons generates ion particles. They are accelerated by axial electric field, which forms a plume of a plasma-effect thruster.

• Progress in Superconductivity and Cryogenics
• /
• v.22 no.1
• /
• pp.12-16
• /
• 2020

As high homogeneity in magnetic field is required to increase the resolution of MRI magnets, various shimming methods have been researched. Using one of them, the design of the superconducting active zonal shim coil for MRI magnets is discussed in this paper. The magnetic field of the MRI magnet is expressed as the sum of spherical harmonic terms, and the optimized current density of shim coils capable of removing higher-order terms is calculated by the Tikhonov regularization method. To investigate all potential designs derived from calculated current density, 4 sweeping parameters are selected: (1) axial length of shim coil zone; (2) radius of shim coils; (3) exact axial position of shim coils; and (4) operating current. After adequate designs are determined with constraints of critical current margin and homogeneity criterion, the total wire length required for each is calculated and the design with a minimum of them is chosen. Using the superconducting wire length of 9.77 km, the field homogeneity over 50 cm DSV is improved from 24 ppm to 1.87 ppm in the case study for 9.4 T whole-body MRI shimming. Finally, the results are compared with the finite element method (FEM) simulation results to validate the feasibility and accuracy of the design.