• 대한기계학회논문집A
• /
• 제41권5호
• /
• pp.391-399
• /
• 2017

절삭속도 및 이송속도가 평엔드밀로 하향절삭 가공된 측벽 형상에 미치는 영향을 실험을 통하여 알아보고자 한다. 실험은 절삭속도 및 공구 직경, 절삭날 당 이송거리를 변수로 하여 수행하며, 실험 결과로서 배분력과 축방향 형상을 측정한다. 연구 결과, 이송속도를 절삭속도로 나눈 값에 비례하는 날 당 이송거리가 작을수록 축방향 형상정밀도가 높아지는 것이 확인되었다. 아울러, 축방향 형상은 서로 다른 기울기를 갖는 두 직선이 특이점에서 만나는 형태로 단순화 할 수 있다. 그러므로 운전 중 작업자에 의한 형상정밀도의 추정 및 날 당 이송거리 조정에 의한 개선이 용이할 것으로 판단된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.490-495
• /
• 2009

In this study, estimate solution of ultimate axial capacity for axial loaded pile is proposed using step-wised shape. This is verified for effective appling on realistic factor by calibration chamber tests. Estimation method of ultimate axial capacity in this study is verified by calibration chamber test. The results of ultimate axial capacity through this proposed method have sufficiently low standard derivations and COVs. Also, this is verified through test that method is similarly resulted with measured values.

• 한국유체기계학회 논문집
• /
• 제3권4호
• /
• pp.30-37
• /
• 2000

Several reverse design methods are developed and applied to the suction or pressure surface for finding design values of blade geometry for a given axial turbine blade. Re-designed blade profiles using shape parameters are compared with measured blade data. Essential shape parameters for blade design are induced by the procedure of reverse design for best fitting. Characteristics of shape parameters are evaluated through the system design method and restriction conditions of structural stability or aerodynamic flow loss. Some of shape parameters i.e blade radius or exit blade angle etc., are classified to weakly adjustable shape parameters, otherwise strongly adjustable shape parameters which would be applied for controlling blade shape. Average deviation values between the measured data and re-designed blade using shape parameters are calculated for each design method. Comparing with the average deviation for a given blade geometry, minimum shape parameters required to design a blade geometry are obtained.

• 한국유체기계학회 논문집
• /
• 제9권3호
• /
• pp.7-13
• /
• 2006

Shape optimization of a rotor blade in a single-stage transonic axial compressor has been performed using a response surface method and three-dimensional Navier-Stokes analysis. Two shape variables of the rotor blade, which are used to define a blade skew, are introduced to increase an adiabatic efficiency. Throughout the shape optimization of a rotor blade, the adiabatic efficiency is increased to about 2.2 percent compared to that of the reference shape of the stator. The increase in efficiency for the optimal shape of the rotor is due to the pressure enhancement, which is mainly caused by moving the separation position on the suction surface of rotor blade to the downstream direction.

• 대한기계학회논문집B
• /
• 제29권5호
• /
• pp.625-632
• /
• 2005

This paper describes the shape optimization of a stator blade in a single-stage transonic axial compressor. The blade optimization has been performed using response surface method and three-dimensional Navier-Stokes analysis. Two shape variables of the stator blade, which are used to define a stacking line, are introduced to increase an adiabatic efficiency. Data points for response evaluations have been selected by D-optimal design, and linear programming method has been used for an optimization on a response surface. Throughout the shape optimization of a stator blade, the adiabatic efficiency is increased to 5.8 percent compared to that of the reference shape of the stator. The increase of the efficiency is mainly caused by the pressure enhancement in the stator blade. Flow separation on the blade suction surface of the stator is also improved by optimizing the stator blade. It is noted that the optimization of the stator blade is also useful method to increase the adiabatic efficiency in the axial compressor as well as the optimization of a rotor blade, which is widely used now.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제26회 춘계학술대회논문집
• /
• pp.297-305
• /
• 2006

본 논문에서는 터빈의 형상 변수에 따른 부분흡입형 초음속 터빈 손실 특성을 분석하기 위하여 초음속 노즐 형상, 축방향 간극 길이, 로터 앞전의 모서리각에 따른 초음속 터빈내 유동 해석을 실시하였다. 먼저 축방향 간극을 진행하면서 발생하는 유동의 익렬 팁방향의 휘어짐은 초음속 노즐 형상에 크게 영향을 받는다. 다음으로 모서리각은 익렬 앞전에서 발생하는 충격파등의 강도를 결정한다. 마지막으로 축방향 간극에서 발생하는 유동의 확산 및 혼합은 축방향 간극 길이에 크게 영향을 받았다. 따라서 터빈내에서 발생하는 손실 중 유체역학적 손실은 노즐 형상과 로터 앞전의 모서리각에 의해 결정되었으며, 부분 흡입 손실은 노즐 형상 및 축방향 간극 길이에 영향을 받았다.

• 드라이브 ㆍ 컨트롤
• /
• 제10권1호
• /
• pp.14-20
• /
• 2013

In the high rotational speed and pressure state, the leakage flow rate of the axial piston pump is one of the serious problems and make great reasons to decrease the volume efficiency. In this study, tribology characteristics is clarified for the hydrostatic slipper bearing in the swash plate type axial piston pump, by means of theoretical analysis for the different shape of the hydrostatic slipper bearing. It was analyzed by Mathcad software and used equal conditions at $0^{\circ}$ swash plate angle in each model. The results show that performance characteristics of the swash plate type axial piston pump are significantly influenced by the shape of the hydrostatic slipper bearing.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.209-214
• /
• 2001

Most reinforce concrete Columns of Building structure are subjected to both axial load and biaxial bending. However, It is hard to estimate the moment capacity of biaxial bending by exact solution. Thus, columns under biaxial bending are designed by approximate methods in practice. The purpose of this study is to compare experimental result with approximate methods and exact solution by computer. Parameters of the present test are compressive strength of concrete (350, 585, 650kgf/$\textrm{cm}^2$) and shape ratio of rectangular section. Ultimately, an experimental shape factor for rectangular RC column section is obtained through the test program. The shape of load contour is dominated by this shape factor obtained experimentally. So, reasonable design of RC columns subjected to both axial compression and biaxial bending depends on load contour.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.543-544
• /
• 2006

Shape optimization of a transonic axial compressor rotor operating at the design flow condition has been performed using three-dimensional Navier-Stokes analysis and three different surrogate models: i.e.., Response Surface Method(RSM), Kriging Method, and Radial Basis Function(RBF). Three design variables of blade sweep, lean and skew are introduced to optimize the three-dimensional stacking line of the rotor blade. The object function of the shape optimization is selected as an adiabatic efficiency. Throughout the shape optimization of the rotor blade, the adiabatic efficiency is increased for the three different surrogate models. Detailed flow characteristics at the optimal blade shape obtained by different optimization method are drawn and discussed.

• Journal of Welding and Joining
• /
• 제21권6호
• /
• pp.40-45
• /
• 2003

Steel members have advantages of resisting torsion and axial compression. In design, residual stresses at the welded joint of T-shape steel pipes are one of the most important points to be considered. In this paper, characteristics of residual stresses of welded joints are clarified by carrying out 3D non-steady heat conduction analysis and 3D thermal elastic-plastic FE-analysis. According to the results, the production mechanism of residual stresses at the welded joint of T-shape steel pipe is clarified. In this paper, circumferential stresses depended on thermal histories but axial and radial stresses were more dependent on geometrical shape than thermal histories. Residual stresses in the axial direction on the lower part of pipe member were tensile, controlled by geometrical shape. However, in case of middle part, residual stresses in all the directions were controlled by thermal histories.