• Tribology and Lubricants
• /
• 제20권2호
• /
• pp.68-76
• /
• 2004

Applying a general Galerkin FE lubrication analysis method to spiral groove dry gas seals, this study intends to analyze in detail the effects of groove design parameters, such as a spiral angle, groove width ratio, groove radius ratio, groove depth ratio, and groove taper ratio, on the lubrication performances of an opening force, leakage, axial stiffness and damping, and angular stiffness and damping at low and high rotating speeds: 3,600 and 15,000 nm. Results show that, for the primary design consideration performances such as the opening force and axial and angular stiffnesses, a spiral angle of $25^{\circ}$, a groove width ratio of 0.46, a groove radius ratio of 1.1, a groove depth ratio of 1.0, and a groove taper ratio of 0.0 are preferred. Where the recommended relatively low values of groove depth and taper ratios are to keep the axial and angular dampings positive or higher than 0 particularly at the high rotating speed.

• 한국강구조학회 논문집
• /
• 제15권3호
• /
• pp.251-259
• /
• 2003

본 논문은 매립형 SRC기둥의 축력과 변형능력과의 관계를 찾아내기 위하여 해석적인 연구를 수행하였다. 해석 모델은 캔틸레버기둥으로 한정하였으며 SRC 기둥의 비탄성 거동에 영향을 미치는 변수들인 철골비, 매립철골형상과 전단스팬과 춤과의 비에 대하여 검토하였다. 일정회전각하에 축력과 반복수평력을 받는 SRC기둥의 안정적 거동을 보장하기 위한 최대한계축력이 있다는 것을 해석결과들은 보여 주고 있다. 반복 횡하중을 받는 기둥이 저항할 수 있는 최대축력은 소요회전각을 보장하는 안정한계축력으로서 정의된다. 해석결과에 따르면 안정한 계축력비는 강재의 강도가 증가함에 따라 콘크리트의 강도가 감소함에 따라 증가하는 것으로 나타났다. 또한 I형 단면이 매립형 철골로 사용될때 철골 단면적이 증가함에 따라 안정한계 축력비는 증가하며, 십자형 단면이 사용되는 경우에는 단면적에 의한 영향이 거의 없었다.

• 전산구조공학
• /
• 제8권4호
• /
• pp.159-171
• /
• 1995

한 cycle의 이력곡선 loop을 완전히 표현하기 위해서는 pinch force, drift offset, effective stiffness, unloading, reloading, tangential stiffness 등의 변수가 필요하게 된다. 각 이력 loop에 대해 이들 변수들은 에너지 소산정도에 따라 변위와 축력의 함수로 표현될 수 있다. 본 논문에서는 먼저 16개의 전단벽 실험에서 얻어진 이력곡선 데이타를 분석하여 앞에 기술된 모든 변수를 표준화된 변위(.DELTA/.DELTA.y)의 함수로 표현했으며 이를 바탕으로 이력곡선의 포락선으로 표현되는 힘-변위관계를 예측할 수 있는 6개의 step을 제시하였다. 제시된 기법으로 구해진 비탄성 힘-변위관계는 실험곡선과 비교되었으며 내진설계에 있어서 가장 중요한 요소중 하나인 구조물의 비탄성 힘-변위관계를 예측하는 편리한 기법으로 이용될 수 있음을 보였다.

• 한국강구조학회 논문집
• /
• 제23권3호
• /
• pp.327-335
• /
• 2011

본 연구의 목적은 강구조 비가새 골조의 열화특성에 영향을 미치는 구조적 인자들을 해석적인 방법으로 평가하고 설계 초기 단계에서 열화 현상을 근사적으로 평가할 수 있는 방안을 제안하는데 있다. 해석적 연구를 위해 arc length method를 적용한 2차원 2차 수정 소성힌지 해석법을 적용하였으며, 단층 단스팬 골조와 다층 단스팬, 다층 다스팬 골조에 대해 해석을 수행하였다. 해석의 주요 변수로는 축력비와 기둥 보의 강성변화를 적용하였다. 연구 결과 무차원 열화강성은 부재의 강성과 축력비에 모두 영향을 받는 것으로 나타났으나, 축력비가 열화강성에 주는 영향이 더욱 큰 것으로 나타났다. 이를 바탕으로 축력비를 변수로 한 열화 강성 평가식을 제안하였다.

• 한국강구조학회 논문집
• /
• 제19권1호
• /
• pp.117-127
• /
• 2007

이 연구에서는 기둥에 축방향 하중을 받고 있는 강재 상자단면 접합부의 강도를 이론적 해석적 검토를 통하여 평가하였다. 2층 교각구조에서는 기둥에 작용하고 있는 축방향 하중의 영향으로 T형 접합부 강도가 저하되게 된다. 이러한 현상을 검토하기 위해 비선형 유한요소해석을 수행하였고, 실험결과와의 비교를 통하여 유한요소 해석프로그램 및 해석방법의 타당성을 검증하였다. 강재라멘교각 접합부의 설계변수 중 패널존의 폭-두께비 파라메타와 플랜지와 복부판의 단면적비 및 기둥에 작용하는 축방향 하중의 영향을 비선형 유한요소해석을 통하여 검토하였다. 또한 이 연구에서는 축방향 하중의 증가에 따른 T형 상자단면 접합부의 응력분포를 이용하여 이론적인 강도평가식을 유도하였다. 또한 1층 교각 구조의 상자단면 접합부 강도특성과 비교하였다. 결국, 패널존의 폭-두께비 파라메타와 단면적비의 영향을 고려하여 T형 접합부의 강도평가식을 제안하였다.

• Tribology and Lubricants
• /
• 제14권4호
• /
• pp.23-28
• /
• 1998

To increase the efficiency of the hydraulic axial piston pumps, it is need to know the various characteristics in the sliding contact parts of them. Especially, friction characteristics between the cylinder block and the valve plate in the hydraulic axial piston pumps plays an important role to high power density. In this paper, we tried to clarify friction characteristics between the cylinder block and the spherical valve plate in bent-axis-type axial piston pump in experimentally. Results are arranged as follow; (1) friction torque between the cylinder block and the spherical valve plate has a proportional relation to weight or rotational speed, and is strongly affected by temperature. (2) Friction torque strongly depends on force balance ratio in valve plate. (3) In this experiment, lubrication condition between the cylinder block and the spherical valve plate is under hydrodynamic lubrication.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.249-255
• /
• 1998

To increase the efficiency of the hydraulic axial piston pumps, we have to know the various characteristics in the sliding parts of them. Especially, friction characteristics between the cylinder block and the valve plate in the hydraulic axial piston pumps plays an important role to high power density. In this paper, we tried to clarify friction characteristics between the cylinder block and the spherical valve plate in bent-axis-type axial piston pump by using of modeling experiment. The main results of this study are these; (1) Friction torque between the cylinder block and the spherical valve plate has a proportional relation to weight or rotational speed, and is strongly affected by temperature. (2) Friction torque strongly depends on force balance ratio. (3) In this experiment, lubrication condition between the cylinder block and the spherical valve plate is under hydrodynamic lubrication.

• Structural Monitoring and Maintenance
• /
• 제4권2호
• /
• pp.153-173
• /
• 2017

An improved method is presented to estimate the axial force of a bar member with vibrational measurements based on modified Timoshenko beam theory. Bending stiffness effects, rotational inertia, shear deformation, rotational inertia caused by shear deformation are all taken into account. Axial forces are estimated with certain natural frequency and corresponding mode shape, which are acquired from dynamic tests with five accelerometers. In the paper, modified Timoshenko beam theory is first presented with the inclusion of axial force and rotational inertia effects. Consistent mass and stiffness matrices for the modified Timoshenko beam theory are derived and then used in finite element simulations to investigate force identification accuracy under different boundary conditions and the influence of critical axial force ratio. The deformation coefficient which accounts for rotational inertia effects of the shearing deformation is discussed, and the relationship between the changing wave speed and the frequency is comprehensively examined to improve accuracy of the deformation coefficient. Finally, dynamic tests are conducted in our laboratory to identify progressive axial forces of a steel plate and a truss structure respectively. And the axial forces identified by the proposed method are in good agreement with the forces measured by FBG sensors and strain gauges. A significant advantage of this axial force identification method is that no assumption on boundary conditions is needed and excellent force identification accuracy can be achieved.

• Steel and Composite Structures
• /
• 제45권5호
• /
• pp.749-766
• /
• 2022

This paper investigates the seismic performance of exposed RCFST column-base joints, in which the high-strength steel bars (USD 685) are set through the column and reinforced concrete foundation without any base plate and anchor bolts. Three specimens with different axial force ratios (n = 0, 0.25, and 0.5) were tested under cyclic loadings. Finite element analysis (FEA) models were validated in the basic indexes and failure mode. The hysteresis behavior of the exposed RCFST column-base joints was studied by the parametrical analysis including six parameters: width of column (D), width-thickness ratio (D/t), axial force ratio (n), shear-span ratio (L/D), steel tube strength (f_y) and concrete strength (f_c). The bending moment of the exposed RCFST column-base joint increased with D, f_y and f_c. But the D/t and L/D play a little effect on the bending capacity of the new column-base joint. Finally, the calculation formula is proposed to assess the bending moment capacities, and the accuracy and stability of the formula are verified.

• 한국생산제조학회지
• /
• 제9권4호
• /
• pp.91-98
• /
• 2000

In this paper , presented is a method of on-line estimation of the radial immersion ratio and cutting force ratio using cutting force. When a tooth finishes sweeping, sudden drop of cutting forces occurs. These force drops are equal to the cutting forces that act on a single tooth at the swept angle of cut and can be obtained from cutting force signals in feed and crossfeed directions. The ratio of cutting forces in feed and cross-feed directions acting on the single tooth at the swept angle of cut is a function of the swept angle of cut and the ratio of radial to tangential cutting force. In the research, it is found that the ratio of radial to tangential cutting force is not affected by cutting conditions and axial rake angle. Therefore, the ratio of radial to tangential cutting force determined by just one preliminary experiment can be used regardless of the cutting conditions. Using the measured cutting forces, the radial immersion ratio is estimated along with the cutting force ratio at that immersion angle. Various experiments show that the radial immersion ratio and instantaneous ratio of the radial to tangential direction cutting force can be estimated by the proposed method very well.