• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.101-107
• /
• 2007

This study investigated the wear of the valve and seat insert seating faces. A tester, an exhaust valve and a seat insert were used. Test variables were cycle numbers ($2{\times}10^6,\;4{\times}10^6,\;6{\times}10^6\;and\;8{\times}10^6$) and Hz (10Hz and 25Hz). The other test conditions such as temperature ($350^{\circ}C$), fuel (LPG) and load (1960N) were fixed. The 10Hz tests indicated that the average Rmax of the valve increased at the rate of $7.76{\mu}m/10^6$ cycles starting from $29.42{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $8.57{\mu}m/10^6$ cycles starting from $34.19{\mu}m$ at the $2{\times}10^6$ cycles. The 25Hz tests indicated that the average Rmax of the valve increased at the rate of $1.58{\mu}m/10^6$ cycles starting from $74.2{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $1.25{\mu}m/10^6$ cycles starting from $83.95{\mu}m$ at the $2{\times}10^6$ cycles. The tribochemical reaction product covered the two seating faces, preventing the wear of the seating faces. As cycle numbers became greater, the average Rmax of the seating faces became greater, but the increase rate varied significantly depending on the Hz. The wear mechanism of the two faces was investigated through the tribochemical reaction.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.9
• /
• pp.1323-1329
• /
• 2015

The WO₃/Ag/WO₃ transparent thin films are fabricated by the RF magnetron sputtering. This has a transmittance of front and rear about 90% in the visible light range and surface resistance of 6.41Ω/□. In this paper, we analyzed the surface characteristics caused by the working pressure and O₂ plasma surface treatment to apply a transparent electrode that was prepared to the laminated structure with other materials. The working pressure was changed in the WO₃ film to 10mTorr, 7mTorr, and 5mTorr, it showed a lower than roughness of conventional ITO. In addition, by 55.5774 J/m² at 5mTorr, it shows the hydrophobic property with lower process pressure. O₂ plasma surface treatment was changed at the condisions of the RF power to 150W, 100W, and 50W and the process time to 240s, 180s, 120s, and 60s. The surface roughness are the maximum roughness(Rmax) 6.437nm and the average roughness(Rq) 0.827nm at RF power 150W, and the maximum roughness (Rmax) 6.880nm and the average roughness (Rq) 0.839nm at process time 240sec. It showed a lower value than the surface treatment. also about working pressure and process time is increased, it showed the hydrophobic.

• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.4
• /
• pp.72-77
• /
• 1992

In this study, using in-process tool failure detecting system by AE method in turning machining, we measured AE signal from the tool, and the surface roughness of workpiece and then compared it with tool wear. As a result, we found that tool failure can be predicted by means of surface roughness of the workpiece and it can be predicted more precisely by the arithmetical average roughness (Ra) than by the maximum height of irregularities (Rmax) of the workpiece. Also, we found that we could judge whether it was sudden failure or the wear by means of the shape of AE signal and the range distri- bution of power spectrum frequency when tool danage was happened.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.18 no.1
• /
• pp.22-28
• /
• 2009

In order to optimize the polishing process, Run to Run control scheme has been applied to the micro mold polishing in this study. Also, to fully understand the effect of parameters on the surface roughness a design of experiment is performed. By linear approximation of main factors such as gap and rotational speed of micro quill, EWMA (Exponential Weighted Moving Average) gradual mode controller is adopted as a optimizing tool. Consequently, the process converged quickly at a target value of surface roughness Ra 10nm and Rmax 50nm, and was hardly affected by unwanted process noises like initial surface quality and wear of magnetic abrasives.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.1
• /
• pp.597-604
• /
• 2016

The aim of this study was to prevent the decrease in crop output by disease and insect pests and excessive spraying of agricultural pesticides by application uniformity. A 3m height and 15km/h speed is difficult to maintain with an unmanned helicopter for aerial application, which has been affected by the controlling habits and methods or environmental factors, such as changes in the wind. Therefore, in this study, an aerial application system was design to be attached to an unmanned helicopter, which can allow a controlled application width and spray rate automatically and verified experimentally using Rmax of MS-AVIATION. The size of agricultural land was 50 m2 and nine water sensitive cards were arranged at 1.25m intervals in 5 rows with each row having a 10m interval from the position of 5m. The unmanned helicopter was flying at speeds ranging from 7.2km/h to 17.6km/h and heights ranging from 2.32m to 3.47m. The proposed aerial application system allowed application uniformity by making a valid spraying area of 7.5 m2 with 46423 particles distributed on average.

• Economic and Environmental Geology
• /
• v.19 no.spc
• /
• pp.121-130
• /
• 1986

In the Janggun mine, stannite occurs as anhedral grains, up to 500 micrometer in long dimension, closely associated with sphalerite, chalcopyrite, arsenopyrite, pyrrhotite, galena and rhodochrosite in the periphery of the South ore body. In reflected light, stannite is grayish yellow green in color and exhibits moderate bireflectance and strong anisotropism without any intenal reflections. Reflection; Rmax. =29.0, Rmin. =27.8 percent at a wavelength of 560nm, and VHN; 219~244kg/mm at a 50g load. The chemical composition on the average from 35 spot analyses by electron microprobe is, Cu 28.0, Fe 12.7, Zn 2.9, Mn 0.2, Sn 25.8, S 30.3, sum 99.9 (all in weight percent); the corresponding chemical formula as calculated on the basis of total atoms=8 is, Cu 1.88 Fe 0.97 Zn 0.19 Mn 0.02 Sn 0.93 S 4.01, which fulfills approximately the ideal formula of $Cu_2FeSnS_4$. The strongest reflections on the X-ray diffraction patterns are; $3.10{\AA}$ (10) (112), $2.72{\AA}$ (5) (020, 004), $1.922{\AA}$ (5) (024), $1.642{\AA}$ (3) (132), $1.244{\AA}$ (3) (143, 136, 235), $1.111{\AA}$(3) (244), $0.958{\AA}$ (1) (048, 422), the patterns are identical with those of literature. From the textural evidence of the microscopic observation, the mineral is considered to have been formed at the middle stage of hydrothermal lead-zinc-silver mineralization.