• 제목/요약/키워드: Average cutting forces

검색결과 28건 처리시간 0.024초

엔드밀 가공에서의 절삭력 모델링에 관한 연구 (A Study on the Modeling for Cutting Force)

  • 김성청
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
    • /
    • pp.58-65
    • /
    • 2000
  • This study is concerned about the verification and the implementation of a mechanical model for the force system in end milling. The model is based on the relationship between the cutting forces and the chip thickness. The components of the model are based on the average cutting forces which are experimentally obtained. And, both instantaneous and average force system characteristics are described as a function of cut geometry and a feed rate. This model employed two specific cutting forces, instantaneous and average specific cutting force, and the models which obtained using two cutting forces were compared and analyzed. In this study, cutter deflection with respect to the center of rotation is considered, which is a major part of the tool run-outs. The effect of run-out on the cutting forces is also discussed. The relationships among the run-out parameters, cutting parameters and the resulting force system characteristics are presented. In all cases, for the down milling with a right hand helix cutter is considered.

  • PDF

Z-map과 절삭계수를 이용한 볼엔드밀의 평균절삭력 예측 (Prediction of Mean Cutting Force in Ball-end Milling using 2-map and Cutting Parameter)

  • 황인길;김규만;주종남
    • 한국정밀공학회:학술대회논문집
    • /
    • 한국정밀공학회 1995년도 추계학술대회 논문집
    • /
    • pp.179-184
    • /
    • 1995
  • A new cutting parameter is defined in the spherical part of ball end-mill cutter. A series of slot cutting experiments were carried out to obtain the cutting parameter. The cutter contact area is expressed as the grid posiotion in the cutting plane using Z map. The cutting forces in each grid are calculated and saved as force map, prior to the average cutting forces calculation. The cutting force, in the arbitrary cutting area, can be easily calculated by summing up the cutting forces of the engaged grid in the force map. This model was verified in the inclined surface cutting by cutting test of a cylindrical part.

  • PDF

엔드밀 가공의 절삭력 예측 및 실험 (Prediction and Experiments of Cutting Forces in End Milling)

  • 이신영;임용묵
    • 한국공작기계학회논문집
    • /
    • 제13권4호
    • /
    • pp.9-15
    • /
    • 2004
  • A reasonable analysis of cutting force in end milling may give much advantage to improvement of productivity and cutting tool life. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. The specific cutting constants of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, feed, axial depth, and radial depth of cut. The model is verified through comparisons of model predicted cutting forces with measured cutting forces obtained from machining experiments. The results showed good agreement and from that we could predict reasonably the cutting forces in end milling.

Specific Cutting Force Coefficients Modeling of End Milling by Neural Network

  • Lee, Sin-Young;Lee, Jang-Moo
    • Journal of Mechanical Science and Technology
    • /
    • 제14권6호
    • /
    • pp.622-632
    • /
    • 2000
  • In a high precision vertical machining center, the estimation of cutting forces is important for many reasons such as prediction of chatter vibration, surface roughness and so on. The cutting forces are difficult to predict because they are very complex and time variant. In order to predict the cutting forces of end-milling processes for various cutting conditions, their mathematical model is important and the model is based on chip load, cutting geometry, and the relationship between cutting forces and chip loads. Specific cutting force coefficients of the model have been obtained as interpolation function types by averaging forces of cutting tests. In this paper the coefficients are obtained by neural network and the results of the conventional method and those of the proposed method are compared. The results show that the neural network method gives more correct values than the function type and that in the learning stage as the omitted number of experimental data increase the average errors increase as well.

  • PDF

마늘 주아 수확기 개발을 위한 마늘종의 역학적 특성 분석 (Mechanical Characteristics of Garlic Scapes for Developing Mechanical Garlic Bulbils Harvester)

  • 서정덕;김건회;권순홍
    • Journal of Biosystems Engineering
    • /
    • 제30권2호
    • /
    • pp.75-80
    • /
    • 2005
  • Mechanical characteristics of flower stalks (scapes) of garlic such as shear forces, cutting forces, and modulus of elasticities were investigated as a preliminary research to develop a mechanical harvester of garlic bulbils. The average shear forces of garlic scapes was 0.642 N and the maximum and minimum shear forces were 1.42 and 0.25 N, respectively. The shear forces generally increased as the diameter of garlic scapes increased. There was no correlation between the modulus of elasticity and the diameter of garlic scapes and the average modulus of elasticity of garlic scapes was around $2.40\times10^7\;N/m^2$ There was also no correlation between the cutting force and the diameter of garlic scapes. As the downward speed of blade increased, the cutting force of garlic scapes decreased and reversed to increase. The cutting forces of the lower part garlic scapes were lower than those of the upper part. The range of cutting forces of the lower and the upper part of garlic scapes were 3.88-4.04 N and 4.29-4.93 N, respectively.

정면 밀링에서 절삭력을 이용한 반경 방향 절입비의 실시간 추정 (On-line Estimation of Radial Immersion Ratio in Face Milling Using Cutting Force)

  • 황지홍;오영탁;권원태;주종남
    • 한국정밀공학회지
    • /
    • 제16권8호
    • /
    • pp.178-185
    • /
    • 1999
  • In tool condition monitoring systems, parameters should be set to a certain threshold. In many cases, however, the threshold is dependent on cutting conditions, especially the radial immersion ratio. In this presented is a method of on-line estimation of the radial immersion ratio in face milling. When a tooth finishes sweeping, a sudden drop of cutting force occurs. The force drop is equal to the cutting force that acting on a tooth at the swept angle of cut and can be acquired from cutting force signals in feed and cross-feed directions. Average cutting force per tooth period can also be calculated from cutting force signals in two directions. The ratio to cutting forces in two directions acting on a tooth at a certain swept angle of cut and the ratio of average cutting forces in two directions per tooth period are functions of the swept angle of cut and the ratio of radial to tangential cutting forces. Using these parameters, the radial immersion ratio is estimated. Various experiments are performed to verify the proposed method. The results show that the radial immersion ratio can be estimated by this method regardless of other cutting conditions.

  • PDF

엔드밀 가공시 절삭조건이 비절삭력계수에 미치는 영향 (Effects of Cutting Conditions on Specific Cutting Force Coefficients in End Milling)

  • 이신영
    • 한국공작기계학회논문집
    • /
    • 제13권6호
    • /
    • pp.1-9
    • /
    • 2004
  • For improvement of productivity and cutting tool lift, cutting force in end milling needs to be predicted accurately. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. Specific cutting force coefficients of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, fled, axial depth and radial depth of cut. The effects of the cutting conditions on the specific cutting force constants in milling were studied. The model is verified through comparisons of model predicted cutting forces with measured cutting forces obtained from machining experiments.

밀링가공시 절삭조건이 비절삭력계수에 미치는 영향 분석 (Effects of Cutting Conditions on Specific Cutting Force Coefficients in Milling)

  • 이신영
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 2004년도 춘계학술대회 논문집
    • /
    • pp.93-98
    • /
    • 2004
  • A reasonable analysis of cutting force in end milling may give much advantage to improvement of productivity and cutting tool life. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. Specific cutting constants of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, feed, axial depth, and radial depth of cut. The effects of the cutting conditions on the specific cutting force constants in milling were studied. The model is verified through comparisons of model predicted cutting forces with measured culling forces obtained from machining experiments

  • PDF

정면 밀링 가공에서의 비절삭 저항 모델링 및 절삭력 예측 (Modeling of the Specific Cutting Pressure and Prediction of the Cutting Forces in Face Milling)

  • 김국원;주정훈;이우영;최성주
    • 한국공작기계학회논문집
    • /
    • 제17권5호
    • /
    • pp.116-122
    • /
    • 2008
  • In order to establish automation or optimization of the machining process, predictions of the forces in machining are often needed. A new model fur farces in milling with the experimental model based on the specific cutting pressure and the Oxley's predictive machining theory has been developed and is presented in this paper. The specific cutting pressure is calculated according to the definition of the 3 dimensional cutting forces suggested by Oxley and some preliminary milling experiments. Using the model, the average cutting forces and force variation against cutter rotation in milling can be predicted. Milling experimental tests are conducted to verify the model and the predictive results agree well with the experimental results.

다층 신경회로망에 의한 밀링가공의 절삭력 시뮬레이션 (Simulating Cutting Forces in Milling Machines Using Multi-layered Neural Networks)

  • 이신영
    • 한국생산제조학회지
    • /
    • 제25권4호
    • /
    • pp.271-280
    • /
    • 2016
  • Predicting cutting forces in machine tools is essential to productivity improvement and process control in the manufacturing field. Furthermore, milling machining is more complicated than turning machining. Therefore, several studies have been conducted previously to simulate milling forces; this study aims to simulate the cutting forces in milling machines using multi-layered neural networks. In the experiments, the number of layers in these networks was 3 and 4 and the number of neurons in the hidden layers was varied from 20 to 200. The root mean square errors of simulated cutting force components were obtained from taught and untaught data for the various neural networks. Results show that the error trends for untaught data were non-uniform because of the complex nature of the cutting force components, which was caused by different cutting factors and nonlinear characteristics coming into play. However, trends for taught data showed a very good coincidence.