• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.3
• /
• pp.228-239
• /
• 2004

In this paper, an analytical model accounting for the quantum effects in MOSFETs has been developed to study the behaviour of $high-{\kappa}$ dielectrics and to calculate the threshold voltage of the device considering two dielectrics gate stack. The effect of variation in gate stack thickness and permittivity on surface potential, inversion layer charge density, threshold voltage, and $I_D-V_D$ characteristics have also been studied. This work aims at presenting a relation between the physical gate dielectric thickness, dielectric constant and substrate doping concentration to achieve targeted threshold voltage, together with minimizing the effect of gate tunneling current. The results so obtained are compared with the available simulated data and the other models available in the literature and show good agreement.

• Steel and Composite Structures
• /
• v.23 no.5
• /
• pp.493-499
• /
• 2017

The behaviour of steel frames is highly influenced by the beam-column connections. Traditionally, Steel frames were usually designed assuming that connections are ideally pinned or fully rigid. A semi-rigid connection, however, creates a balance between the two extreme approaches mentioned above. In this research, two full scales of Extended End Plate Connections (EEPCs) were tested. Mathematical and numerical models were used to analyse the connections, and close correlations were found between these models and the corresponding tested specimens, which confirmed the confidence in the experimental results. The experimental results obtained enrich the available test data about behaviour of EEPC. In addition, the purpose of studying EEPC experimentally is to compare the stiffness and moment-rotation curve of EEPCs with that of Cap Plate Connections (CPCs), which were tested in a previous work. CPCs have not been studied sufficiently in the literature. The results obtained show that the typical CPC reduces the connection stiffness and these results will make a valuable contribution to the available test data in the research area of CPC.

• Asia pacific journal of information systems
• /
• v.4 no.2
• /
• pp.214-246
• /
• 1994

As the use of information technology continues to bring a dramatic increase in the amount of data available to managers, researchers have noted that having too much data can be as much of a problem as having too little. It becomes very important to understand the effects of "information explosion" on the way managers perform their work. This study examines the effect of the amount of available data on the process and outcome of thinking within a context where managers are equipped with computing tools. The purpose of this study is to better understand how managers respond cognitively to increased information availability. In this experiment with 104 MBAs three groups of subjects were asked to identify high and low potential market categories for effective direct mail sales based on three different amount of computer-based socioeconomic data designed based on existing research on cognition and information overload. Analyses of the outcomes showed that the group with medium amount of data used data and computer-based analysis tools most effectively and efficiently. We expect that the study will provide us a base to relate future MIS research to theories on cognition in such related fields as psychology and organizational behavior.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.1
• /
• pp.38-54
• /
• 1996

Respirator fit testing is required before entering specific work environmentals to ensure that the respirator worn satisfies a minimum of fit and that the user knows when the respirator fits properly. The fit of a respirator can be determined by qualitative (QLFT) or quantitative fit test (QNFT). The QNFT, having been universally accepted more than the QLFT, provide an objective and numerical basis by measuring a fit factor (FF). Until a few years age, only one QNFT technigue was available and accepted by U.S. Occupational Safety and Health Administration (OSHA) regulations. In the 1980's and 1990's, several new and fundamentally different QNFT methods were developed. Two of the newer methods are commercially availale and are accepted by OSHA as suitable alternatives. In this articles, the principle of operation of each ONFT technique is explained and each technique's major advantages and disadvantages are pointed out. Emphasis is given to negative-pressure air-purifying respirators, as they are in most frequent use today. The requirements and recommendations for fit testing positive-pressure respirators are discussed as well. Finally, the presently available QNFT standards and regulations are summarized to assist the user in making fit testing decisions.

• Industrial Engineering and Management Systems
• /
• v.13 no.4
• /
• pp.369-382
• /
• 2014

This paper introduces a new multi-product multi-period multi-objective aggregate production planning problem. The proposed problem is modeled using multi-objective mixed-integer mathematical programming. Three objective functions, including minimizing total cost, maximizing customer services level, and maximizing the quality of end-product, are considered, simultaneously. Several constraints such as quantity of production, available time, work force levels, inventory levels, backordering levels, machine capacity, warehouse space and available budget are also considered. Some parameters of the proposed model are assumed to be qualitative and modeled using fuzzy sets. Then, a fuzzy goal programming approach is proposed to solve the model. The proposed approach is applied on a real-world industrial case study of a color and resin production company called Teiph-Saipa. The approach is coded using LINGO software. The efficacy and applicability of the proposed approach are illustrated in the case study. The results of proposed approach are compared with those of the existing experimental methods used in the company. The relative dominance of the proposed approach is revealed in comparison with the experimental method. Finally, a data dictionary, including the way of gathering data for running the model, is proposed in order to facilitate the re-implementation of the model for future development and case studies.

• Steel and Composite Structures
• /
• v.12 no.5
• /
• pp.395-412
• /
• 2012

The present work addresses the rotational capacity of steel-concrete composite beams, which is a key issue for the seismic design of composite frames. Several experimental tests from the literature are summarised, and the effects of various parameters on the available plastic rotation are discussed. Furthermore, a number of remarks are made regarding the need for supplementary experimental results. The authors carried out experimental tests on four composite beams in which the type, width and connection degree of the slab were varied. During the tests, the deflection and strains in the steel profiles and bars were measured and recorded, wherein the observed trends in the measured parameters indicated that the failure mode of the beam was influenced by global and local buckling. A comparison of the experimental results to the theoretical ultimate strengths and moment-curvature relationships confirms that buckling phenomena occurred after section yielding, even if a consistent plastic rotation developed. This rotational capacity is well evaluated by a formulation that is available in the literature.

• Computers and Concrete
• /
• v.21 no.1
• /
• pp.95-102
• /
• 2018

Reinforced concrete corbel beams (span to depth ratio of a corbel is less than one) are designed with primary reinforcement bars to account for bending moment and with the secondary reinforcement placed parallel to the primary reinforcement (shear stirrups) to resist shear force. It is interesting to note that most of the available analytical procedures employ empirical formulas for the analysis of reinforced concrete corbels. In the present work, a generalized and a simple strut and tie models were employed for the analysis of reinforced corbel beams. The models were benchmarked against experimental results available in the literature. It was shown here that increase of shear stirrups increases the load carrying capacity of reinforced concrete corbel beams. The effect of horizontal load on the load carrying capacity of the corbel beams has also been examined in the present paper. It is observed from the strut and tie models that the resistance of the corbel beam subjected to combined horizontal and vertical load did not change with increase in shear stirrups if the failure of the corbel is limited by concrete crushing. In other words, the load carrying capacity was independent of the horizontal load when failure of the beam occurred due to concrete crushing.

• Safety and Health at Work
• /
• v.3 no.3
• /
• pp.166-180
• /
• 2012

This review summarizes the epidemiology of cancer of the female reproductive system and associated lifestyle factors. It also assesses the available evidence for occupational factors associated with these cancers. Cervical, endometrial, and ovarian cancers are relatively common, and cause significant cancer morbidity and mortality worldwide, whereas vulvar, vaginal, fallopian tube cancers, and choriocarcinomas are very rare. As several lifestyle factors are known to play a major role in the etiology of these cancers, very few published studies have investigated possible relationships with occupational factors. Some occupational exposures have been associated with increased risks of these cancers, but apart from the available evidence on the relationships between asbestos fibers and ovarian cancer, and tetrachloroethylene and cervical cancer, the data is rather scarce. Given the multifactorial nature of cancers of the female reproductive system, it is of the utmost importance to conduct occupational studies that will gather detailed data on potential individual confounding factors, in particular reproductive history and other factors that influence the body's hormonal environment, together with information on socio-economic status and lifestyle factors, including physical activity from multiple sources. Studies on the mechanisms of carcinogenesis in the female reproductive organs are also needed in order to elucidate the possible role of chemical exposures in the development of these cancers.

• Agribusiness and Information Management
• /
• v.11 no.2
• /
• pp.5-15
• /
• 2019

The world of smart agribusiness is still far from being fully and effectively applied by the Italian entrepreneurial fabric. In part, this is due to the fact that its potential and important connections with the technological world of reference are not fully known. The imperative is therefore: to learn how to manage all the processes that characterize the agricultural chain in a synergistic way, from production to the sale of the product to the final consumer. It is therefore essential to know every minimum aspect of the supply chain considering the current strengths on which to leverage but especially the weaknesses on which to intervene thanks to the use of technology available on the market. Today, the supply chain is still considered as a set of phases, one consecutive to the other, as if they were detached from each other. However, in order to operate efficiently, each step should be interconnected: from the farmer's decision to produce an agricultural good to the choice of production factors, from the implementation of harvesting and post-harvest operations to processing, from the selection of goods suitable for sale to the logic of distribution on the target territory. This work investigates the potential strategy using digital technologies in order to make dynamic the agribusiness supply chain, especially because in Italy the agri-food is one of the most important economic sectors but it is far from the most innovative trends available on the market.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2013.11a
• /
• pp.165-168
• /
• 2013

Image distortions, such as quantization errors, can have a severe negative impact on the performance of computer vision algorithms, and, more specifically, on object detection algorithms. State-of-the-art implementations of the JPEG-2000 image coder commonly allocate the available bits to minimize the Mean-Squared-Error (MSE) distortion between the original image and the resulting compressed image. However, considering that some state-of-the-art object detection methods use the gradient information as the main image feature, an improved object detection performance is expected for JPEG-2000 image coders that allocate the available bits to minimize the distortions on the gradient content. Accordingly, in this work, the Gradient Mean-Squared-Error (GMSE) based JPEG-2000 coder presents an improved object detection performance over the MSE based JPEG-2000 image coder when the object of interest is located at the same spatial location of the image regions with the strongest gradients and also for high bit-rates. For low bit-rates (e.g. 0.07bpp), the GMSE based JPEG-2000 image coder becomes overly selective in choosing the gradients to preserve, and, as a result, there is a greater chance of mismatch between the spatial locations of the gradients that the coder is trying to preserve and the spatial locations of the objects of interest.