• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.4
• /
• pp.58-67
• /
• 1998

A sectional analysis of sheet metal forming process with an arbitrary tool shape is proposed in the present work. To improve the numerical convergence in the conventional membrane sectional analysis, the Bending Energy Augmented Membrane (BEAM) elements had been developed. The BEAM elements particularly improve the stability and convergence of the finite element method for the case of deep drawing. In this work, the FERGUBON spline (C$^2$-continuous) was used to fit the deformed mesh to smooth the given curves and calculate the local curvature of the deformed sheet. The fittings of the deformed sheet and tool surface profile ensure the stability and the convergence of the finite element analysis of highly nonlinear stamping processes. A center floor section and front fender section are analyzed to show the accuracy and robustness of the approach. The results obtained by the proposed approach are compared with the available experimental data.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• v.3 no.2
• /
• pp.137-142
• /
• 1999

One of the most important parameters required to model the absorption of CO2 into aqueous alkanolamine solutions is physical solubility. However, since CO2 reacts in amine solutions, its physical solubility cannot be measured directly. As a result, a nonreacting gas which is similar to CO2 has to be used such as N2O. The solubility of nitrous oxide (N2O) in aqueous solutions of 0wt%-50wt% MDEA, 0wt%-30wt% DEA, and 50wt % total amine with DEA/MDEA molar ratios of 0.05, 0.25, 0.5 and 0.67 was measured using a modified Zipperclave reactor over a temperature range of 293-353 K with near atmospheric partial pressures of N2O. the solubility data from this work were K with near atmospheric partial pressures of N2O. The solubility data from this work were found to be in good agreement with previously reported data where available.

• IE interfaces
• /
• v.3 no.2
• /
• pp.39-51
• /
• 1990

One of the most important and powerful tools available for design and/or study of the operation of complex systems and processes is simulation. Since automated material handling systems like AS/RS are often quite complex, a network-based simulation model is developed to analyze an automobile part supplier's automated storage and retrieval system(AS/RS). The network simulation model is implemented in the SLAM Ⅱ on a VAX 8800 computer. Performance of the AS/RS was tested for 3 dispatching rules, 3 work load levels, 2 storage policies, 3 levels of stacker crane break-down, and 2 conveyor system layouts. Results indicate that the AS/RS performance is primarily affected by the dispatching rule and work load level.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.172-180
• /
• 2006

Although there existed many types of manual/power hybrid wheelchairs, their use was not widespread because of their inconvenience in converting drive system and in folding frames. To carry a wheelchair in the car or to convert driving methods, some hard work of disassembling or exchanging wheels was required for most of currently available hybrid wheelchairs. In this study, the standard foldable manual wheelchair was reformed to a power wheelchair by installing the newly developed Axial Flux Permanent Magnet(AFPM) type of brush less direct current(BLDC) motor on each rear hub of wheelchair. This wheelchair could be driven by manual or electric power without exchanging. wheels, thus no additional work was needed for carriage or for power conversion. The developed wheelchair was evaluated for durability, stability, maneuverability, cost, and reliability in accordance with the Korean standards. The results indicated that the developed hybrid wheelchair was good enough for commercialization comparing to other imported wheelchairs.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.2
• /
• pp.34-38
• /
• 2008

Commercially available magnetic barrel machines equipped with permanent magnets have certain limitations: work can only be finished effectively in limited areas of the container because permanent magnets are arranged two-dimensionally on the magnet disk. We overcame this problem by developing a new magnetic barrel machine equipped with a three-dimensional magnet arrangement. The effectiveness of the new machine has already been reported; this study improved the machine's polishing ability by changing the polarity of magnets on a magnet block. Polishing experiments confirmed the most effective arrangement of magnets on the magnet block. An alternating arrangement of north and south poles produced far superior polishing characteristics than a uniform arrangement of the same pole facing outward. Alternating polarity probably causes increased quantities of barrel media to work together. Finally, we introduced stronger permanent magnets to the magnet block, and found that the increased magnetic field also improved polishing ability.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.6
• /
• pp.95-103
• /
• 1998

Solutions of geotechnical engineering problems require calculation of deformation and stresses during various stages of loading. Powerful numerical methods are available to make such calculation even for complicated problems. To get accurate results, realistic stress-strain relationships of soil are dependent on a number of factors such as soil type, density, stress level and stress path. Attempts are continuously being made to develope analytical models for soils incorporating all such factors. The nature of stress-path dependency, the principle that governs deformations in sand, and the use of Lade's single work-hardening model for predicting sand response for a variety of stress-paths have been investigated and are examined. The test results and the analyses presented show that under some conditions sand exhibits stress-path dependent behavior. The strains calculated from Lade's single work-hardening model are in reasonable agreement with those measured, but some discrepancies occur. The largest difference between measured and calculated strains occurs for proportional loading with increasing stresses and for stress-path directions.

• Journal of the Korea Safety Management & Science
• /
• v.1 no.1
• /
• pp.69-77
• /
• 1999

One of the objectives of any task design is to provide a safe and helpful workplace for the employees. The safety and health module may include means for confronting the design with safety and health regulations and standards as well as tools for obstacles and collisions detection (such as error models and simulators), Virtual Reality is a leading edge technology which has only very recently become available on platforms and at prices accessible to the majority of simulation engineers. The design of an automated manufacturing system is a complicated, multidisciplinary task that requires involvement of several specialists. In this paper, a design procedure that facilitates the safety and ergonomic considerations of an automated manufacturing system are described. The procedure consists of the following major steps. Data collection and analysis of the data, creation of a three-dimensional simulation model of the work environment, simulation for safety analysis and risk assessment, development of safety solutions, selection of the preferred solutions, implementation of the selected solutions, reporting, and training. When improving the safety of an existing system the three-dimensional simulation model helps the designer to perceive the work from operators point of view objectively and safely without the exposure to hazards of the actual system.

• Structural Engineering and Mechanics
• /
• v.63 no.5
• /
• pp.683-689
• /
• 2017

In this paper, a hyperbolic shear deformation theory is presented for bending analysis of functionally graded beams. This theory used in displacement field in terms of thickness co-ordinate to represent the shear deformation effects and does not require shear correction factor, and gives rise to transverse shear stress variation such that the transverse shear stresses vary parabolically across the thickness satisfying shear stress free surface conditions. The governing equations are derived by employing the virtual work principle and the physical neutral surface concept. A simply supported functionally graded beam subjected to uniformly distributed loads and sinusoidal loads are consider for detail numerical study. The accuracy of the present solutions is verified by comparing the obtained results with available published ones.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.2
• /
• pp.259-269
• /
• 2015

The issue of the longitudinal stability of a WIG vehicle has been a very critical design factor since the first experimental WIG vehicle has been built. A series of studies had been performed and focused on the longitudinal stability analysis. However, most studies focused on the longitudinal stability of WIG vehicle in cruise phase, and less is available on the longitudinal static stability requirement of WIG vehicle when hydrodynamics are considered: WIG vehicle usually take off from water. The present work focuses on stability requirement for longitudinal motion from taking off to landing. The model of dynamics for a WIG vehicle was developed taking into account the aerodynamic, hydrostatic and hydrodynamic forces, and then was analyzed. Following with the longitudinal static stability analysis, effect of hydrofoil was discussed. Locations of CG, aerodynamic center in pitch, aerodynamic center in height and hydrodynamic center in heave were illustrated for a stabilized WIG vehicle. The present work will further improve the longitudinal static stability theory for WIG vehicle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.831-838
• /
• 2004

A fluid-solid conjugate solver has been newly developed and applied to an actual engine disk system. Most of the currently available conjugate solvers lack the special thermal modeling for turbomachinery disk system applications. In the present new code, these special models are implemented to expand the applicability of the conjugate method and to reduce the required computational resources. Most of the conjugate analysis work so far are limited to the axisymmetric framework. However, the actual disk system includes several non-axisymmetric components which inevitably affect the local heat transfer phenomena. Also the previous work devoted to this area usually concentrate their efforts on the steady-state thermal field, although the one in the transient condition is more critical to the engine components. This paper presents full 3D conjugate analysis of a single stage high pressure turbine rotor-stator disk system to assess the three-dimensional effects (Fig. 1). The analysis is carried out not only in the steady-state but also in the engine accelerating transient condition. The predicted temperatures shows good agreement with measured data.