• Journal of Magnetics
• /
• 제21권1호
• /
• pp.72-77
• /
• 2016

Although the initial cost of permanent-magnet linear synchronous motors is high owing to the installation of armatures over the full length of the transportation lines, linear motors are useful for transportation systems because of their high speed, acceleration, and deceleration. For these reasons, research into reducing the cost of linear motors is necessary, and a stationary distributed-armature system has been suggested for installing armatures in sections where acceleration and deceleration of the mover are required. However, each armature has ends that significantly increase the cogging force, resulting in the increase in the thrust ripple of the mover. Therefore, in order to improve the thrust ripple of the system, the present study aims to provide auxiliary teeth on both ends of the armature to achieve an optimal design through an analysis of the contribution ratio with respect to factors regarding the design of the experiment and the objective function.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권9호
• /
• pp.525-531
• /
• 2004

This paper proposes inserted core type of slotless Permanent Magnet Linear Synchronous Motor(PMLSM) to improve its low thrust density. However, by inserting the core between windings of each phase, detent force is generated and it acts as thrust ripple. Furthermore, linear motors generate end effect making thrust ripple. So, this paper applies the neural network to minimize detent force and to maximize thrust. Also, sub-poles is placed at the end parts of the mover to compensate end effect. To confirm of calculation method's validity, the calculated results are compared with experimental results.

• 전기학회논문지
• /
• 제65권1호
• /
• pp.65-72
• /
• 2016

This paper presents the analysis of the analysis of thrust characteristics of linear induction motors(LIMs) according to secondary reaction plate. LIMs are well known as high speed transport systems, which can obtain thrust directly without gears and links, or auxiliary mechanisms. A simple structure, easy maintenance, and less environmental pollution are advantages of LIMs. In transport systems using LIMs, the secondary reaction plate is an important design factor, because it has considerable impact on the cost of the railway as well as the performance of the LIMs. This paper deals analyzed the characteristics of linear induction motor used for moving the vehicle of container scanner. Thrust, efficiency and load characteristic were interpreted with FEM regarding two models whose material of secondary reaction plate was copper and aluminum. It suggested the interpretation of thrust, efficiency and power factor characteristic along slip and compared the operation ability of linear induction motor through characteristics analysis along the load.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.730-731
• /
• 2015

This paper presents the analysis of the analysis of thrust characteristics of linear induction motors(LIMs) according to secondary reaction plate. LIMs are well known as high speed transport systems, which can obtain thrust directly without gears and links, or auxiliary mechanisms. A simple structure, easy maintenance, and less environmental pollution are advantages of LIMs. In transport systems using LIMs, the secondary reaction plate is an important design factor, because it has considerable impact on the cost of the railway as well as the performance of the LIMs.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권9호
• /
• pp.459-464
• /
• 2006

The detent force by end-effect has an undesired influence on moving coil type Permanent Magnet Linear Synchronous Motor(PMLSM). So, the reduction of detent force by end-effect is especially required for the improvement of thrust characteristics. In this paper, in order to reduce detent force by end-effect, the auxiliary-teeth is installed at the end part of mover. It is also analyzed by Finite Element Analysis(FEA) and optimized by using neural network. By comparison, the detent force is reduced about 41.4[%] comparing to that of basic model.

• 대한조선학회논문집
• /
• 제58권6호
• /
• pp.415-423
• /
• 2021

There have been many experimental studies on the manoeuvrability of KRISO Container Ship (KCS). However, the scale ratio of the model ship and the test procedure for each institute are slightly different, so direct comparison for the data is technically difficult to perform. This paper presents the manoeuvrability of the ship with different scale ratios: 1/65.8, 1/42.0, and 1/31.6 in model scale. KRISO conducted Free Running Model Tests (FRMT): 35° turning circle tests and 20/20(10/10) zigzag manoeuvring tests. The test results indicated that advance and tactical diameter in turning circle tests were similar, and overshoot angles in two zigzag manoeuvring tests increased as the model ship size increased. In addition, a basic concept for the FRMT method with an auxiliary X-thrust device was proposed so that the scale effect could be considered in model ship tests.

• 한국전자통신학회논문지
• /
• 제8권11호
• /
• pp.1675-1680
• /
• 2013

최근 저소음, 고속, 고추력의 반송장치가 요구됨에 따라 영구자석 선형동기전동기가 대두되고 있으나 반송경로 전장에 전기자를 설치하는 선형 동기전동기의 특성으로 인해 장거리 반송장치에 적용시 설치비용의 증가를 가져온다. 따라서 우리는 전기자를 분산시켜 배치하는 방법을 제안하여 비용증가의 문제점을 해결하고자 하였다. 하지만 가동자의 진행시 분산배치된 전기자 사이를 통과하게 되면 전기자의 불연속 구간인 단부에 의해 디텐트력이 발생하여 추력 맥동이 발생하고 기기 성능저하와 소음, 진동의 원인이 된다. 따라서 본 논문에서는 단부에 의한 영향을 저감하기 위해 전기자 끝단의 치 높이와 보조치 형상에 따른 디텐트력의 특성을 파악하고 다구찌의 실험계획법을 이용하여 단부 효과를 가장 저감할 수 있는 형상을 제안하였다.

• 한국전자통신학회논문지
• /
• 제7권5호
• /
• pp.1067-1072
• /
• 2012

현재 선형 전동기는 많은 연구가 진행되어 그 응용분야가 산업전반에 확대되고 있다. 이중 반송장치 분야에서 영구자석 선형 동기 전동기(Permanent Magnet Linear Synchronous Motor:이하 PMLSM)가 각광을 받고 있다. 영구자석 선형 동기 전동기는 구조적으로 간단하며 고속화 고추력화 등의 장점을 가지고 있지만 전기자를 반송경로 전장에 배치하는 지상 1차측 시스템을 장거리 반송장치에 적용하면 재료비용의 증가 및 제작시간 증가 등의 문제점이 발생한다. 따라서 전기자를 분산(불연속) 배치하는 방식이 제안되고 있다. 하지만 이러한 전기자 분산배치 방식은 구조적으로 단부가 존재하고 이러한 단부에 의해 코깅력이 발생한다. 이는 추력 맥동의 원인이 되며, 소음과 진동을 발생시킨다. 따라서, 본 연구에서는 전기자를 분산배치 할 경우 필연적으로 생기는 단부에 의한 코깅력을 저감하기 위해 Bifurcating을 적용한 집중권 PMLSM에 보조극 설치법을 제안한다. 또한 그에 따른 단부 코깅력 특성을 2차원 유한요소법(FEA)을 이용하여 분석하였다.

• 한국전자통신학회논문지
• /
• 제6권6호
• /
• pp.889-895
• /
• 2011

영구자석 선형 동기 전동기(Permanent Magnet Linear Synchronous Motor:이하 PMLSM)는 구조적으로 간단하며 고속화 고추력화 등의 많은 장점을 가지고 있지만 전기자 권선부의 슬롯-치 구조로 인한 코깅력과 단부효과에 의한 코깅력이 발생한다. 이는 추력 맥동의 원인이 되며, 소음과 진동을 발생시킨다. 따라서, 본 연구에서는 전기자를 분산배치 할 경우 필연적으로 생기는 단부에 의한 코깅력을 저감하기 위해 PMLSM의 가동자에 보조극의 설치를 제안하였다. 또한 2차원 유한요소법(Finite Element Analysis)을 이용하여 단부 코깅력이 최소가 되는 보조극의 형태를 설계하고 전기자의 권선 방식에 따른 단부 코깅력 특성을 비교하였다.

• 한국정밀공학회지
• /
• 제21권11호
• /
• pp.91-98
• /
• 2004

TFLIM(Transverse Flux Linear Induction Motor), making its closed magnetic path with the direction of the traveling field orthogonal, had been developed to decrease an edge effect of the general induction motor. To control the levitation force and the thrust force on the secondary part of TFLIM independently, the various methodologies have been presented. When we try to achieve the independent control using only the multi-phase inputs assigned in the stator coils as an approach, in which condition we can minimize the coupling effect between two forces\ulcorner In this paper, we show the qualitative influence of a slip frequency, an ac magnitude, a dc offset superposed in the ac power, and a major parameter of TFLIM on the couple through the computer simulation. And to realize the independent motions between levitation and thrust motion without any auxiliary means fur isolation of the secondary part of TFLIM, the decouple compensator is suggested, including the experimental results.