• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.247-249
• /
• 2001

In our research, we designed a small step motor with 2-phase structure and a micro step driving IC, which is used in an automotive instrument. The step motor for the automotive instrument has the better advantages than a cross coil type motor. These advantages are the characteristics with a good linearity, a fine accuracy, a low noise and so on.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.208-210
• /
• 2005

A lot of conventional automotive components driven by mechanical power source are being replated with electrical ones to comply with the demands of market and customer, therefore the amount of electric energy used in a vehicle will be increased continuously. The increment of electric power demand causes interest on new higher power system such as 42V Power Net, and furthermore necessity for development of energy storage device is highlighted recently. This paper presents the design of the BLDC motor drive for Cooling Fan in 42V automotive system. Test results confirmed the feasibility of the proposed motor drive system design.

• International Journal of Reliability and Applications
• /
• 제15권2호
• /
• pp.151-161
• /
• 2014

Recently, the automotive industry has been introduced to ISO 26262 in November 2011 to address the necessity of safety risk from sensor to actuator by providing guidance in the form of requirements and processes. The malfunctioning behaviour of these systems could have significant impact on the safety of humans and/or the environment. Most of the modern automobiles are equipped with embedded electronic systems which include lots of Electronic Controller Units (ECUs), electronic sensors, signals, bus systems and coding. Due to the complex application in electrical, electronics and programmable electronics, the need to carry out detailed safety analyses which focuses on the potential risk of malfunction is crucial for automotive systems. In this paper, the international trends on pre and post introduction of ISO 26262 through publications will be analyzed as well as to take a glimpse in the activities for implementing this standard by the automotive manufacturers. The issues and challenges which have been occurring from implementing this standard also will be highlighted.

• 한국자동차공학회논문집
• /
• 제21권2호
• /
• pp.159-165
• /
• 2013

ESD damage by Charged Cable Model (CCM) is introduced. Due to its own impedance characteristic unlike Human Body Model (HBM) or Machine Model (MM) electric component can be destroyed even though it is located after typical protection circuit. Possible mechanism of ESD damage to automotive electric control unit (ECU) in vehicle environment by CCM discharge was investigated. Based on investigation, field-returned vehicle whose ECU is expected to be damaged by CCM discharge was tested to reproduce it and similar electric component destruction inside ECU was observed. Suggestions to reduce the possibility of ESD damage by CCM are introduced.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.92-97
• /
• 2011

Vehicle lightings are very important for safe driving during night time. Since the eye recovery time after an exposure to oncoming headlights would take after several seconds, the aiming point of vehicle head lamps have to pass safety requirements. Despite the fact that vehicle inclination is variable with vehicle load conditions, the head lamps aiming point is usually fixed at a constant position which is set by car manufacturer. Consequently, vehicle head lamps under varying load conditions often make people in the opposing vehicle uncomfortable, and even worse, can cause an accident. This paper presents an active vehicle lighting mechanism to automatically adjust its aiming point, or cut-off line, in order to compensate the change in vehicle inclination resulting from load variations. The effectiveness of the proposed method is demonstrated through a set of simulations and experiments with a real vehicle.

• 전력전자학회논문지
• /
• 제26권5호
• /
• pp.364-371
• /
• 2021

A magnetic flux saturation model of Synchronous Reluctance Motors (SynRMs) and a parameter estimation method are proposed at standstill. The proposed magnetic flux model includes the nonlinear relationship between the current and the magnetic flux for self-saturation and cross-saturation. Voltage is injected at standstill to estimate the magnetic flux saturation model. Voltages are injected into the d-axis and q-axis to obtain data on self-saturation. Subsequently, voltages are simultaneously injected into the d-q axis to obtain data on cross-saturation. On the basis of the measured current and the calculated magnetic flux, the parameters of the proposed model are estimated using the least square method (LSM). Simulation and experiment were performed on a 1.5-kW SynRM to verify the proposed method. The proposed model can be used to create a high-efficiency operation table, a sensorless algorithm, and a current controller to improve the control performance of a motor.

• Journal of Power Electronics
• /
• 제19권5호
• /
• pp.1087-1098
• /
• 2019

In this paper, a detuning factor (DeFac) method is proposed to design the key parameters for optimizing the transfer power and efficiency of an Inductively Coupled Power Transfer (ICPT) system with primary-secondary side compensation. Depending on the robustness of the system, the DeFac method can guarantee the stability of the transfer power and efficiency of an ICPT system within a certain range of resistive-capacitive or resistive-inductive loads. A MATLAB-Simulink model of a ICPT system was built to assess the system's main evaluation criteria, namely its maximum power ratio (PR) and efficiency, in terms of different approaches. In addition, a magnetic field simulation model was built using Ansoft to specify the leakage flux and current density. Simulation results show that both the maximum PR and efficiency of the ICPT system can reach almost 70% despite the severe detuning imposed by the DeFac method. The system also exhibited low levels of leakage flux and a high current density. Experimental results confirmed the validity and feasibility of an ICPT system using DeFac-designed parameters.

• Journal of Power Electronics
• /
• 제9권1호
• /
• pp.68-73
• /
• 2009

Automotive inverters may require current sensors for motor torque control, especially, in applications of hybrid electric vehicles or fuel cell vehicles. In this paper, to achieve a compact, integrated and low cost current sensor, a hall current sensor without magnetic core is introduced for integrating an automotive inverter. The compactness of the current sensor is possible by using integrated magnetic concentrators based on the Hall effect. Magnetic fields caused by three-phase currents are analyzed and a magnetic shield design is proposed for decoupling the cross-coupled field. It offers galvanic isolation, wide bandwidth (>100kHz), and accuracy(< 1%). Using 2D FEM analysis, its performance is demonstrated with design parameters at a U-shaped magnetic shield. The proposed coreless current sensor is tested with rated current to validate the linearity and accuracy.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2015년도 전력전자학술대회 논문집
• /
• pp.139-140
• /
• 2015

차량용 에어컨 시스템은 엔진의 가동(주행 또는 공회전)에 의해 발생되는 에너지를 이용하여 운전자가 원하는 차량 실내온도를 유지시켜주는 장치를 말한다. 이러한 기계식 에어컨 시스템의 작동은 엔진 구동력의 일부를 활용하고 있어 자동차의 연비와 큰 관련성 있다. 때문에 하절기 작업 대기시나 차량 내 야간취침 등이 빈번한 상용차량의 경우 운전자의 운행습관에 따라 연료 소비량이 증가하는 단점을 가지고 있다. 본 논문에서는 이러한 단점을 개선하고자 대형 상용차량이 정차중인 무시동 기간에도 일정 온도의 유지가 가능 하도록 전력변환장치가 적용된 에어컨 시스템을 제안하였다.

• Journal of Power Electronics
• /
• 제19권3호
• /
• pp.625-636
• /
• 2019

This paper proposes an active leakage magnetic field (LMF) suppression scheme, which uses the dual-transmitter (DT) topology, for EV wireless charging systems (EVWCS). The two transmitter coils are coplanar, concentric and driven by separate inverters. The LMF components generated by the three coils cancel each other out to reduce the total field strength. This paper gives a detailed theoretical analysis on the operating principles of the proposed scheme. Finite element analysis is used to simulate the LMF distribution patterns. Experimental results show that when there is no coil misalignment, 97% of the LMF strength can be suppressed in a 1kW prototype. These results also show that the impact on efficiency is small. The trade-off between LMF suppression and efficiency is revealed, and a control strategy to balance these two objectives is presented.