• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.05a
• /
• pp.507-509
• /
• 2022

In order to collect vehicle internal diagnostic data, it is necessary to collect diagnostic data of ECU (Electronic Control Unit) included in various automotive parts. Diagnostic communication can be used to collect diagnostic data of ECU. In this paper, the method of collecting diagnostic data according to ECU function through standard diagnostic communication and the diagnostic communication module were analyzed. Among the standard modules of AUTOSAR, a standard for automotive electronics used by many automobile manufacturers, the diagnostic communication module was studied, and the process of diagnostic data processing through ECU was studied.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.543-544
• /
• 2011

최근 고유가 문제와 환경에 대한 관심 증가로 인해 친환경저연비 자동차에 대한 기술 연구가 다양한 분야에서 활발히 진행되고 있다. 이 가운데서도 특히 반도체 및 배터리의 급속한 기술발전으로 자동차용 부품들이 기계식 방식에서 전자식 방식으로 대체되고 있다. 그 중에서 전동식 워터펌프는 엔진의 회전에 연동된 타이밍 벨트로 구동되는 기존의 기계식 펌프와 달리, 펌프부에 전기모터 및 제어기가 결합되어 독립적인 구동능력을 갖추고 있다. 자동차 동력효율을 높이기 위해 내연기관 및 주변 전장장치들의 온도를 주행조건에 따라 제어하여 적정하게 유지시킬 필요가 있으며 이를 위한 자동차 부품으로 전동 워터펌프의 중요성이 커지고 있다. 본 논문에서는 이와 같은 자동차용 전동워터펌프 제어기 개발을 위하여 브러시리스형 DC모터를 적용하였다. 브러시리스형 DC모터는 고속 및 큰 부하에서 Back EMF 대비 전류의 지상 성분이 발생하여 상전류 증가 및 전체 효율을 떨어뜨린다. 이에 본 연구에서는 Lead Angle의 양을 계산하는 기법을 이용하여 워터펌프에 적용하였다.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.391-392
• /
• 2017

최근 자동차 산업의 연구개발의 핵심화두는 효율성 제고 및 NVH(Noise, Vibration, Harshness) 개선에 있다. 특히나 많은 부품들의 개발에 있어서 운전자의 운전 편의성을 높이는 성능적인 지표 외에도 운전자가 느끼는 소음, 이상 진동에 대한 감성성능에 대한 소비자의요구도 높아지고 있다. 이러한 경향에 맞추어 자동차 각 부분의 소음저감, 효율향상을 고려한 설계에 대한 연구가 활발해지고 있다. 많은 자동차 부품들에 모터가 사용되고 있으며, 특히 차량용 쿨링팬의 경우 모터를 사용하여 차량 운행 시 발행하는 (배터리의 온도를) 적절한 수준으로 유지시켜주거나 친환경 자동자차 배터리를 쿨링 하는 역할을 한다. 대다수의 쿨링팬 모터로 BLDC모터가 많이 사용되며 이는 전통적인 제어 방법인 구형파제어를 사용하고 있다. 본 논문에서는 저전압 배터리의 전원을 사용하여 BLDC 쿨링팬을 안정적으로 구동할 수 있는 제어기를 개발하였고, 소음저감 및 높은 효율을 위하여 정현파로 제어하는 기법을 적용하였다. 개발된 시작품의 성능 시험을 통해 그 결과를 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.741-745
• /
• 2001

Reliability and safety of steer-by-wire concepts can be achieved by redundant designs. This paper discusses the design of a fault tolerant concept for a force feedback actuator with a standard three-phase PMSM. In contrast to usual drives, the phases of the machine are separated electrically. This design allows driving the machine with two instead of three phases in case of a fault. A superimposed torque controller adjusts the influence of fault currents and torque harmonics in two-phase operation and guarantees smooth torque at the steering wheel

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.5
• /
• pp.451-458
• /
• 2013

This paper describes a design of LIN MCU using efficient memory accessing architecture which provides concurrent data and address fetch for faster communication. By using slew rate control it can reduce EMI emission while satisfying required communication specifications. To verify the efficiency of the LIN MCU, we developed a SoC and tested for several data packets. Measurements show that this LIN MCU improves network efficiency up to 17.19 % and response time up to 31.26 % for nominal cases. EMI radiation also can be reduced up to 10 dB.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.126-135
• /
• 2014

This paper describes the development and verification of control algorithms for V2X and environmental sensor integrated intersection support and safety systems. The objective of the research is to develop core technologies for effective fusion of V2X and environmental sensors and to develop new safety function for intersection safety. One of core technologies is to achieve the improvement of GPS accuracy, and the other is to develop the algorithm of a vehicle identification which matches all data from V2X, vehicle sensors and environmental sensors to specific vehicles. A intersection optimal pass (IOP) algorithm is designed based on these core technologies. IOP recommends appropriate speed to pass the intersection in the consideration of traffic light signal and preceeding vehicle existence. Another function is developed to prevent a collision avoidance when car crash caused by traffic violation of surrounding vehicles is expected. Finally all functions are implemented and tested in three test vehicles. It is shown that IOP can support convenient and comfortable driving with recommending optimal pass speed and collision avoidance algorithm can effectively prevent collision caused by traffic sign violation of surrounding vehicles.

• 전자공학회논문지 IE
• /
• v.49 no.2
• /
• pp.30-39
• /
• 2012

An effective drowsy driver detection system is needed, because the probability of accident is high for drowsy driving and its severity is high at the time of accident. However, the drowsy driver detection system that uses bio-signals or vision is difficult to be utilized due to high cost. Thus, this paper proposes a drowsy driver detection algorithm by using steering angle sensor, which is attached to the most of vehicles at no additional cost, and vehicle information such as brake switch, throttle position signal, and vehicle speed. The proposed algorithm is based on jerk criterion, which is one of drowsy driver's steering patterns. In this paper, threshold value of each variable is presented and the proposed algorithm is evaluated by using acquired vehicle data from hardware in the loop simulation (HILS) through CAN communication and MATLAB program.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.91-101
• /
• 2014

In this study, we presented a timing verification method for a passenger car diesel engine management system (EMS) using measurement-based worst-case execution time (WCET) analysis. In order to cope with AUTOSAR-compliant software architecture, a development process model is proposed. In the process model, a runnable is regarded as a test unit and its temporal behavior (i.e. maximum observed execution time, MOET) is obtained along with on-target functionality evaluation results during online unit test. Furthermore, a cost-effective framework for online unit test is proposed. Because the runtime environment layer and the standard calibration environment are utilized to implement test interface, additional resource consumption of the target processor is minimized. Using the proposed development process model and unit test framework, the MOETs of 86 runnables for diesel EMS are obtained with 213 unit test cases. Using the obtained MOETs of runnables, the WCETs of tasks are estimated and the schedulability is evaluated. From the schedulability analysis results, the problems of the initially designed schedule table is recognized and it is fixed by redesigning of the runnable mapping and task offset. Through the various test scenarios, the proposed method is validated.

• Journal of the Korean Institute of Gas
• /
• v.21 no.5
• /
• pp.83-88
• /
• 2017

The purpose of this paper is to study for a failure examples producing in electronic control air conditioner in vehicle. The first example, it looked for the repetitive fuse cutting phenomenon that the diode using for a surge voltage prevention of inner A/C relay damaged because of no absorbing the surge voltage by short of diode when the A/C is off. The second example, it knew the icing phenomenon of evaporator that the A/C ECU didn't control the A/C because of inner cutting of fin thermo sensor. The third example, it verified the operation trouble phenomenon because of the A/C switch and for sensor burned in flames by short phenom enon when the sheath of the cable has peeled off. Therefore, the driver have to manage the optimism system of a car by thoroughgoing inspection and improvement the failure phenomenon.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.2
• /
• pp.107-114
• /
• 2014

This paper proposes a common rail pressure control algorithm for passenger car diesel engines. For handling the parameter-varying characteristics of common rail systems, the quantitative feedback theory (QFT) is applied to the design of a robust rail pressure control algorithm. The driving current of the pressure control valve and the common rail pressure are used as the input/output variables for the common rail system model. The model parameter uncertainty ranges are identified through experiments. Rail pressure controller requirements in terms of tracking performance, robust stability, and disturbance rejection are defined on a Nichols chart, and these requirements are fulfilled by designing a compensator and a prefilter in the QFT framework. The proposed common rail pressure control algorithm is validated through engine experiments. The experimental results show that the proposed rail pressure controller has a good degree of consistency under various operating conditions, and it successfully satisfies the requirements for reference tracking and disturbance rejection.