• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.2
• /
• pp.161-168
• /
• 2011

The heating, ventilating, air conditioning (HVAC) system is a very important part of an automotive vehicle: it controls the microclimate inside the passenger's compartment and removes the frost or mist that is produced in cold/rainy weather. In this study, the numerical analysis of the defrost duct in an HVAC system and the de-icing pattern is carried out using commercial CFX-code. The mass flow distribution and flow structure at the outlet of the defrost duct satisfied the duct design specification. For analyzing the de-icing pattern, additional grid generation of solid domain of ice and glass is pre-defined for conductive heat transfer. The flow structure near the windshield, streakline, and temperature fields clearly indicate that the de-icing capacity of the given defrost duct configuration is excellent and that it can be operated in a stable manner. In this paper, the unsteady changes in temperature, water volume fraction, and static enthalpy at four monitoring points are discussed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.04a
• /
• pp.86-92
• /
• 1993

자동차의 현가장치에 대한 능동제어연구는 국내외적으로 활발히 진행되어 왔다. 수동식현가장치는 단순히 스프링과 감쇠기로 차체의 진동을 수동 제어 하므로 성능 향상에 한계가 존재하게 된다. 수동식 현가장치가 강성계수와 감쇠계수를 조절함으로써 차체로 들어오는 진동을 억제하는 반면, 능동식제 어는 보통 유압을 이용하여 효율적으로 차체에 들어오는 진동을 억제시키게 된다. 일반적으로 자동차가 능동현가장치 설계시 요구되는 사항은 탑승자의 승차감, 조종성, 현가장치의 공간확보 문제, 경제성(제어력), 실제적으로 자동 차에 적용할 수 있는 능동제어기법인가 하는 문제이다. 자동차 능동식 현가 장치는 보통 1/4 car (2자유도계), Full-car 모델 (7자유도계) 등으로 모델링 을 하여 능동제어기를 설계한다. 1/4 car 모델의 특징은 해석이 비교적 단순 하고 현가장치의 동적거동을 이해하는데 유용하고 실험을 하거나 실제 자동 차에 적용하기 쉬운 반면에 Full-car 모델에 비해 제어력의 효율이 떨어진다 는 단점이 있다. 그 이유는 1/4 car 모델은 차체의 동역학적 특성을 고려하 여 설계하지 않았기 때문에 4개의 독립현가차축에서는 오직 그 현가축방향 으로 발생하는 수직방향의 진동만을 제어하기 때문이다. 따라서 동역학적 역 성에 기인하는 운동을 제어하는 비효율적인 제어력이 공급된다는 단점을 갖 는다. 이에 비해 full-car 모델은 주행모드(수직, 롤링, 피칭운동)간의 연성을 고려하여 제어기를 설계할 수 있기 때문에 1/4 car 모델에 비해 제어력의 효 율이 높다는 장점이 있는 반면에 모델이 수학적으로 복잡하므로 제어력을 구하는데 계산량이 많고, 실제 자동차에 적용하기에 복잡하다는 단점을 갖고 있다. 따라서 본 논문에서는 쉽게 실험할 수 있고, 실용화할 수 있는 1/4 car 모델에 대하여 능동제어기를 설계하여 실제자동차에 능동제어기를 적용할 때 참고가 될 수 있도록 하였다. 자동차는 저주파영역의 밴드통과필터 역할 을 하므로 저주파에서의 성능, 특히 탑승자가 민감하게 느끼는 0.5Hz - 10Hz 부근의 주파수성능은 승차감, 조종성에 상당히 중요하다. 이에 본 논문 에서는 0.5Hz - 10Hz 부근의 승차감, 조종성의 향상에 초점을 두고 차체의 속도를 출력변수로 한 LQG/LTR 제어기를 설계하였다. LQG/LTR 설계기법 은 안정도-강인성이 좋은 체계적인 설계기법으로서 전 상태를 측정할 필요 가 없으므로 실제 적용시 효과적이다. 또한 자동차의 제원의 변화에 대한 고 유치의 민감도해석과 새로운 개념으로 안정도-강인성(Robustness)해석을 하 여 수동시스템과 능동시스템의 강인성을 비교하였다.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.1
• /
• pp.42-52
• /
• 2012

In this paper, a waveguide antenna is designed and fabricated for side and rear radar sensor of vehicles in UWB (Ultra Wide Band) high band (center frequency : 9.5 GHz, -10 dB bandwidth : 600 MHz (6.4 %)). For the radar antenna, a probe fed rectangular waveguide antenna having simple structure and wide bandwidth is used. An important performance factor in this antenna is the isolation between transmitting (TX) and receiving (RX) waveguide antennas because this radar system uses TX and RX antennas separately. Thus the isolation between two antennas was simulated for E-plane and H-plane array. As a result, it was verified that the isolation of the H-plane array of the antennas is better than E-plane array, due to the TE10 mode. Therefore, H-plane arrayed waveguide antennas were mounted on a T-shaped radar module and performance of antennas was investigated. The -10 dB bandwidth of the TX and RX antenna mounted on T-shaped radar module was measured as 1000 MHz (10.52 %) and 1090 MHz (11.47 %) respectively and the isolation is less than -50 dB in the operation band. The peak gain is 7.65 dBi for the TX antenna and 7.26 dBi for the RX antenna and the beamwidth of H-plane of TX and RX antenna was measured as $64^{\circ}$ and $65^{\circ}$ respectively. Consequently, we verified that the proposed waveguide antenna is appropriate for a vehicle radar applications.

• Journal of the Korean Institute of Gas
• /
• v.18 no.2
• /
• pp.73-80
• /
• 2014

The objective of this paper is to assess the service life and retrain methods of specimens, which were subjected to carbonation attack, obtained from mix proportion of Sam-cheok LNG storage tank under construction. As the results, accelerated-carbonation penetration depths of 7, 28, 56 ages indicated 4.45, 9.19, 13.37mm, and even considering for cover depths of steel of LNG storage tank under real operation, it was enough. In addition, with carbonation velocity coefficient calculated by carbonation penetration depths, the service life to design cover depth(70, 80, 90, 100mm) of PC outer tank of LNG storage tank was 779, 1017, 1287, 1589 years and 466, 609, 771, 951 years, respectively, considering the $CO_2$ concentration in air which account for the 0.03% and 0.05%. Also, the restrain methods to carbonation attack were feasible through controlling the factors affecting the changes of hydration products such as $Ca(OH)_2$, ion composition in pore solution and matter mobility of organization structures within hardened concrete.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.688-695
• /
• 2017

Compared to metal, CFRP has excellent mechanical characteristics in terms of intensity, hardness, and heat resistance as well as its light weight that it is used widely in various fields. Therefore, this material has been used recently in the aerospace field. On the other hand, the material has shortcomings in terms of its extreme vulnerability to damage occurring internally from an external impact. This study examined the intensity up to its destruction from repeated use with the internal impact of a CFRP laminated plate that had also been exposed to external impact obtain design data for the external plate of aircraft used in the aerospace field. For the experimental method, regarding the quasi-isotopic type CFRP specimen and orthotropic CFRP specimen that are produced with a different layer structure, steel spheres with a diameter of 5 mm were collided to observe the resulting impact damage. Through a 3-point flexural fatigue experiment, the progress of internal layer separation and impact damage was observed. Measurements of the flexural fatigue strength after the flexural fatigue experiment until internal damage occurs and the surface impacted by the steel spheres revealed the quasi-isotopic layer structure to have a higher intensity for both cases.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.8
• /
• pp.62-68
• /
• 2016

The feeder cable assembly is an automotive part used for telecommunication. If it malfunctions, the control and safety of the automobile can be put at risk. ALT (Accelerated Life Testing) is a testing process for products in which they are subjected to conditions (stress, strain, temperatures, etc.) in excess of their normal service parameters in an attempt to uncover faults and potential modes of failure in a short amount of time. Failure is caused by defects in the design, process, quality, or application of the part, and these defects are the underlying causes of failure or which initiate a process leading to failure. Thermal shock occurs when a thermal gradient causes different parts of an object to expand by different amounts. Thermal shock testing is performed to determine the ability of parts and components to withstand sudden changes in temperature. In this research, the main causes of failure of the feeder cable assembly were snapping, shorting and electro-pressure resistance failure. Using the Coffin-Manson model for ALT, the normal conditions were from Tmax = $80^{\circ}C$ to Tmin = $-40^{\circ}C$, the accelerated testing conditions were from Tmax = $120^{\circ}C$ to Tmin = $-60^{\circ}C$, the AF (Acceleration Factor) was 2.25 and the testing time was reduced from 1,000 cycles to 444 cycles. Using the Bxlife test, the number of samples was 5, the required life was B0.04%.10years, in the acceleration condition, 747 cycles were obtained. After the thermal shock test under different conditions, the feeder cable assembly was examined by a network analyzer and compared with the Weibull distribution modulus parameter. The results obtained showed good results in acceleration life test mode. For the same reliability rate, the testing time was decreased by a quarter using ALT.

• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.46-52
• /
• 2011

A confocal microscope was developed utilizing a scanning sample stage based on a home-built double-compound flexure guide. A scanning sample stage with nano-scale resolution consisted of a double leaf spring based flexure, a displacement amplifying lever, a Piezo-electric Transducer(PZT) actuator and capacitance sensors. The performance of the two-axis stage was analyzed using a commercial finite element method program prior to the implementation. A single line laser was employed as the light source along with the Photo Multiplier Tube(PMT) that served as the detector. The performance of the developed confocal microscope was evaluated with a mouse ear skin imaging test. The designed scanning stage enabled us to build the confocal microscope without the two optical scanning mirror modules that are essential in the conventional laser scanning confocal microscope. The elimination of the scanning mirror modules makes the optical design of the confocal microscope simpler and more compact than the conventional system.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.4
• /
• pp.143-148
• /
• 2020

In the case of a system that detects and controls the phase of an alternating voltage, the analog control method compensates the phase offset part by filtering for the detected phase and applies it to the control. However, in the digital control method, precise control cannot be achieved due to an error between the operating frequency of the microprocessor or the microcontroller and the input phase time when controlled using such phase detection. In general, when the method used is a certain time, the accumulated error is compensated and adjusted at random. To solve this problem, a method of detecting a zero point in real time and compensating for the operating frequency of the microprocessor is needed. Therefore, the research to be performed in this paper to reduce these errors and apply them to precise digital control is as follows. 1) Research on how to implement Zero Crossing Detection algorithm through simulation modeling to compensate the zero point to match the operating frequency through detection. 2) A study on the method of detecting zero points in real time through the Zero Crossing Detection design using a microcontroller and compensating for the operating frequency of the microprocessor. 3) A study on the estimation of the rotor position of BLDC motors using the Zero Crossing Detection circuit.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.500-509
• /
• 2013

This study reports a numerical analysis of the internal flow characteristics of the integrated urea-SCR muffler system with the various geometries of the multi-perforated tube which is set up between the muffler inlet and in front of SCR catalysts. The multi-perforated tube is generally used to disperse uniformly the urea-water solution spray and to make better use of the SCR catalyst, resulting in the increased $NO_x$ reduction and decreased ammonia slip. The effects of the multi-perforated tube orifice area ratios on the velocity distributions in front of the SCR catalyst, which is ultimately quantified as the uniformity index, were investigated for the optimal muffler system design. The steady flow model was applied by using a general-purpose commercial software package. The air at the room temperature was used as a working fluid, instead of the exhaust gas and urea-water solution spray mixture. From the analysis results, it was clarified that the multi-perforated tube geometry sensitively affected to the formation of the bulk swirling motion inside the plenum chamber set in front of the SCR catalyst and to the uniformity index of the velocity distribution produced at the inlet of the catalyst.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.475-478
• /
• 2011

driver for safety always check the status of their vehicle, and it is essential to understand. But if you want to know the status of the driver of the vehicle in specialist referral time and money because it costs the operator shall be paid. Today's rapidly changing IT technology with the development of the various features of your phone to check the status of the vehicle was able to do. However, the car's existing phone system, car diagnostic expertise must be learned because it will reveal the status of the vehicle do not have the expertise to not highlight the need for diagnostic. To reflect these points in smartphone users to easily use their own vehicles at a time to determine the status of a system that is required. In this paper, OBD-II protocol conversion WiFi OBD-II connector, retrieving information from the driver of the vehicle replacement cycle of consumables required vehicle inspection, vehicle problems in real-time diagnostic information to the user ease of use shows the IOS implementation in the automotive supply was implemented based on the smartphone.