• Journal of the korean Society of Automotive Engineers
• /
• v.23 no.3
• /
• pp.77-78
• /
• 2001

• Journal of the korean Society of Automotive Engineers
• /
• v.23 no.3
• /
• pp.21-23
• /
• 2001

• Journal of the korean Society of Automotive Engineers
• /
• v.31 no.4
• /
• pp.14-20
• /
• 2009

• Journal of the korean Society of Automotive Engineers
• /
• v.31 no.4
• /
• pp.39-47
• /
• 2009

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.139-144
• /
• 2010

In the automotive electronic industry, the development of vehicle's door wiring harness (W/H) system for new applications is driven continuously for the low-cost and the high strength performance for electronic components. The problem of the fatigue strength estimation for materials and components containing natural defects, inclusions, or inhomogeneities is of great importance both scientifically and industrially. This article gives some insight into the dimensioning process with special focus on the fatigue analysis of wiring harness (W/H) in vehicle's door structures. The results from endurance tests using slim test specimens were compared with the results from FEM for predicted fatigue life. The expectation for the life of components is affected by the microstructural features with complex stress state arising from the combined service loading and residual stresses.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.68-74
• /
• 2014

This study analyzes structural stress and fatigue about three types of automotive wheels. As maximum equivalent stresses at 1, 2 and 3 types become lower than the yield stress of material and deformations become minute, theses types are thought be safe on durability. Type 2 model has the most fatigue life among three kinds of types and the rest of models with fatigue lives are shown in the order of type 1 and 3. As the most fatigue frequency of type 2 model happens at the state of average stress and amplitude stress on the stress range narrower than type 1 or 3, type 2 model becomes most stable. In case of type 2 with the state near the average stress of 0 MPa and the amplitude stress of 300MPa, the possibility of maximum damage becomes 30%. This stress state can be shown as the most damage possibility. These study results can be effectively utilized with the design on automotive wheel by anticipating and investigating prevention and durability against its damage.

• Geomechanics and Engineering
• /
• v.14 no.1
• /
• pp.91-98
• /
• 2018

Length of a vehicle is an important variation to generate different variants of an automotive platform. This parameter is usually adjusted by embedding dimensional flexibility into different components of the Body in White (BIW) including the floor pan. Due to future uncertainties, it is not necessarily possible to define certain values of wheelbase for the future products of a platform. This work is performed to add flexibility into the design process of a length-variable floor pan. By means of this analysis, the cost and time consuming process of optimization is not necessary to be performed for designing the different variants of a product family. Stiffness and mass of the floor pan are two important functional requirements of this component which directly affect the occupant comfort, dynamic characteristics, fuel economy and environmental protection of the vehicle. A combination of Genetic algorithm, GMDH-type of artificial neural networks and TOPSIS methods is used to optimally design the floor pan associated with arbitrary length of the variant in the defined system range. The correlation between the optimal results shows that for a constant mass of the floor pan, the first natural frequency decreases by increasing the length of this component.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.145-150
• /
• 2006

Recently emission regulation on diesel vehicles is getting stringent and research on aftertreatment technology such as DPF and DOC has been carried out actively. Even though PM(Particulate matters) reduction efficiency in DOC is relatively low but the structure is simpler and very effective in the reduction of gas materials and unregulated materials. Therefore it has been applied to smaller diesel vehicles. The aims of this research is to investigate the emission reduction characteristics of DOC; DOC performance of regulated and unregulated material emission reduction. It results a Pt based catalyst demonstrated higher emission reduction efficiency than a Pt-V based catalyst in CVS-75 mode, and also the reduction efficiency of unidentified material was excellent.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.111-117
• /
• 2008

The aim of this paper was to investigate the fluid dynamic behavior of the automotive closed type water pump with balance hole in order to evaluate and justify its overall hydraulic performance and, in particular to analyze the effects of the balance hole on the reduction of hydraulic flow force of it. The analysis has been peformed by applying the commercial computational fluid dynamics (CFD) code, Fluent, to the solution of the 3-D turbulent flow fields of automotive closed type water pump. The reliability of the employed analysis was demonstrated by the comparison between numerical result and experimental data. Although, hydraulic head of the closed type water pump with 3mm diameter of balance hole decreased by 1.1%, axial flow force was effectively reduced by 13.3%, comparison of it with no hole at design point.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.1-8
• /
• 2013

Recently, the automotive technology has developed with electronics and information technology as convergence technology while vehicles had been regarded as machines. Moreover, vehicles are becoming more intelligent and safer devices, assembly of advanced technologies by customers' demand. Even though all of installations of vehicle have attracted as diverting devices, it cause drivers' mistakes like delay of response on traffic condition. Here, we proposed the Field Operational Test (FOT) environment which could be used as driving and road conditions collector(Vehicle motion, Traffic condition, Driver input, Driver state, etc.) for researches about Driver Friendly Intelligent System(SCC, LDWS, etc.), Human Vehicle Interface(Driving Workload, etc.) and Economic Drive Model. Furthermore driving patten and fuel consumption patten of drivers were analyzed by measured data and direction of future research was suggested.