• Journal of The Geomorphological Association of Korea
• /
• v.19 no.4
• /
• pp.109-122
• /
• 2012

Topographic changes in the foredune in Sohwang-ri, Boryeong, Chungnam Province was analyzed over the last two years. Seven cross-sections and one permanent plot ($20m{\times}50m$) were periodically studied based on erosion and deposition measurement, in addition to vegetation monitoring and measurement of wind using an automatic weather station. The sand dunes usually grew from late winter to spring and the growth occurred in a period of strong northwesterly winds. From March to April, heavy sedimentation was observed on the front section of the foredune and sand piled up to ca. 30cm to the ca. 25m landward from the high tide line. It is likely that increased wind force and growth of vegetation played a major role in transportation and sedimentation of sand. Meanwhile, the lower part of the sand dunes was eroded when typhoon and spring tide caused a rise in sea level. The transition zone of beach and dune was usually affected by sea water but some frontal slopes were entirely influenced, resulting in dune scarps. The eroded scarps were naturally restored to their original state as time passed.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.5
• /
• pp.369-374
• /
• 2021

Apartment recently built in kitchen is made is made because the gas hose with built-in ways invisible inside the sink. In this case, if the gas leaks, it is a dangerous method that can accumulate inside the sink and lead to an explosion. In this study, since the hose connected between the gas range and the intermediate valve is inside the sink, it is not possible to test for gas leaks, so a valve system that can easily check for gas leaks using a pressure sensor was studied. As for the pressure measurement method, the pressure of the hose connecting the intermediate valve and the gas range was measured so that data could be collected and analyzed using the I2C communication method. In addition, the calculation of the gas pressure supplied to the home was investigated for the atmospheric pressure error for the value calculated by adding the average value of the gas gauge pressure of 22.46 mbar at the inlet of the gas meter to the atmospheric pressure. A valve system was developed to detect minute gas leaks.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.3
• /
• pp.269-277
• /
• 2019

Since 2020, according to the International Convention for the Prevention of Pollution from Ships (MARPOL) amended in 2016, each Administration shall transfer the annual fuel consumption of its registered ships of 5,000 gross tonnage and above to the International Maritime Organization (IMO) after verifying them. The Administration needs stacks of materials, which must not be manipulated by ship companies, including the Engine log book and also bears an administrative burden to verify them by May every year. This study considers using the Automatic Identification System (AIS), mandatory navigational equipment, as an objective and efficient tool among several verification methods. Calculating fuel consumption using a ship's speed in AIS information based on the theory of a relationship between ship speed and fuel consumption was reported in several examples of relevant literature. After pre-filtering by excluding AIS records which had speed errors from the raw data of five domestic cargo vessels, fuel consumptions calculated using Excel software were compared to actual bunker consumptions presented by ship companies. The former consumptions ranged from 96 to 123 percent of the actual bunker consumptions. The difference between two consumptions could be narrowed to within 20 percent if the fuel consumptions for boilers were deducted from the actual bunker consumption. Although further study should be carried out for more accurate calculation methods depending on the burning efficiency of the engine, the propulsion efficiency of the ship, displacement and sea conditions, this method of calculating annual fuel consumption according to the difference between two consumptions is considered to be one of the most useful tools to verify bunker consumption.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.3
• /
• pp.247-255
• /
• 2021

Individual passenger transfer information is not included in Seoul metropolitan subway Automatic Fare Collection (AFC) data. Currently, basic data such as travel time and distance are allocated based on the TagIn terminal ID data records of AFC data. As such, knowledge of the actual path taken by passengers is constrained by the fact that transfers are not applied, resulting in overestimation of the transport index. This research proposes a method by which a transit path that connects the TagIn and TagOut terminal IDs in AFC data is determined and applied to the transit index. The method embodies the concept that a passenger's line of travel also accounts for transfers, and can be applied to the transit index. The path selection model for the passenger calculates the line of transit based on travel time minimization, with in-vehicle time, transfer walking time, and vehicle intervals all incorporated into the travel time. Since the proposed method can take into account estimated passenger movement trajectories, transport-related data of each subway organization included in the trajectories can be accurately explained. The research results in a calculation of 1.47 times the values recorded, and this can be evaluated directly in its ability to better represent the transportation policy index.

• Atmosphere
• /
• v.33 no.4
• /
• pp.413-422
• /
• 2023

Urban Air Mobility (UAM) is promising, sustainable and efficient air transportation in a metropolitan area. Korean government has recently announced operation demonstration plans as a step toward commercialization of UAM. However, there is lack of understanding on the potential impact of weather on UAM operation. We collected weather observations from Gimpo International Airport and 5 automatic weather stations (AWS) along UAM corridor of the Han-River to assess weather barriers such as low visibility, wind gust and wind shear. The results show the frequency of low visibility near the corridor fluctuated significantly from year to year depending on the concentration of fine particulate matter (PM_2.5) in Seoul. The frequency of high wind speed-shift calculated using 1-minute wind observations was increased not only during the spring season (March, April, and May) but also the beginning of rainy season (Jun). In addition, a chance of high wind shear from 1-minute wind observations varied by the stations, suggesting that the condition is largely affected by topography including a river and high-rise buildings. These basic weather properties suggest that there are substantial weather barriers to UAM operations along the Han-River Corridor, while they cannot properly surveil micro-scale weather conditions in detail such as wind gust and wind shear over the corridor. Thus, this study suggests that potential barriers related to adverse weather need to be evaluated, building high-density weather observations infrastructure prior to UAM demonstration and commercialization.

• Journal of Korean Society of Transportation
• /
• v.29 no.5
• /
• pp.121-138
• /
• 2011

More affordable and available cutting-edge technologies (e.g., wireless vehicle communication) are regarded as a possible alternative to the fixed infrastructure-based traffic information system requiring the expensive infrastructure investments and mostly implemented in the uninterrupted freeway network with limited spatial system expansion. This paper develops an advanced decentralized traveler information System (ATIS) using vehicle-to-vehicle (V2V) communication system whose performance (drivers' travel time savings) are enhanced by three complementary functions (autonomous automatic incident detection algorithm, reliable sample size function, and driver behavior model) and evaluates it in the typical $6{\times}6$ urban grid network with non-recurrent traffic state (traffic incident) with the varying key parameters (traffic flow, communication radio range, and penetration ratio), employing the off-the-shelf microscopic simulation model (VISSIM) under the ideal vehicle communication environment. Simulation outputs indicate that as the three key parameters are increased more participating vehicles are involved for traffic data propagation in the less communication groups at the faster data dissemination speed. Also, participating vehicles saved their travel time by dynamically updating the up-to-date traffic states and searching for the new route. Focusing on the travel time difference of (instant) re-routing vehicles, lower traffic flow cases saved more time than higher traffic flow ones. This is because a relatively small number of vehicles in 300vph case re-route during the most system-efficient time period (the early time of the traffic incident) but more vehicles in 514vph case re-route during less system-efficient time period, even after the incident is resolved. Also, normally re-routings on the network-entering links saved more travel time than any other places inside the network except the case where the direct effect of traffic incident triggers vehicle re-routings during the effective incident time period and the location and direction of the incident link determines the spatial distribution of re-routing vehicles.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.112-118
• /
• 2011

The recycled asphalt concrete has gotten increasing attention due to the environmental issues. The volume of reclaimed asphalt has increased significantly for last few years because of city remodeling, pavement maintenance, utility excavation, and road widening. Considering the value of reclaimed asphalt, it is rather used for the recycled asphalt concrete than it is used for fill and cover up material instead of soil. This research will be a supplements incomplete issues from existing research results and suggests the quality control guideline for recycled asphalt concrete and upcoming laws. As the first step of research, the trial construction of RAP(Recycled Asphalt Pavement) performed in expressway construction sites. These trial construction sites have been checked every years. And another construction sites studied and selected for more deeper performance check of RAP. For this checks, we used automatic pavement survey equipment and computerized analysis tools. Also, DSR(Dynamic Shear Rheometer) was used for the fatigue life calculation of binder blends(RAP and virgin binder). As a consequence of this research, the application of recycled asphalt provides good enough quality for highway construction. The preceeding literatures reviewed shows that the asphalt rejuvenator are used in many countries but that type of chemical agent are not used in Korea. By using the data of trial construction and mix design in Chongwon-Sangju construction lane, the surface and base courses consisted with the 10% and 30% rap mix asphalt section maintains good performance for up to 7 years. Through the performance check and laboratory tests(DSR), the quality control and mixture's low temperature prevention are the important factor and chemical agent necessary for increasing the fatigue life of RAP binder.

• Journal of the Ergonomics Society of Korea
• /
• v.36 no.5
• /
• pp.525-533
• /
• 2017

Objective: The aim of this study is to investigate maritime officers' strategies to avoid the ship collision in crossing situations. Background: In a situation where there is a risk of collision between two ships, maritime officers can change the direction and speed of the own-ship to avoid the collision. They have four options to select; adjusting the speed only, the direction only, both the speed and direction at the same time and no action. Research questions were whether the strategy they are using differs according to the shipboard experience of maritime officers and the representation method of ARPA (automatic radar plotting aid) - radar graphic information. Method: Participants were 12. Six of them had more than 3 years of onboard experience, while the others were 4th grade students at Korea Maritime and Ocean University. For each participant, 32 ship encounter situations were provided with ARPA-radar information. 16 situations were presented by the north-up display and 16 situations were presented by the track-up display. Participants were asked to decide how to move the own-ship to avoid the ship collision for each case. Results: Most participants attempted to avoid the collision by adjusting the direction of the ship, representing an average of 22.4 times in 32 judgment trials (about 70%). Participants who did not have experience on board were more likely to control speed and direction at the same time than participants with onboard experience. Participants with onboard experience were more likely to control the direction of the ship only. On the other hand, although the same ARPA Information was provided to the participants, the participants in many cases made different judgments depending on the method of information representation; track-up display and north-up display. It was only 25% that the participants made the same judgment under the same collision situations. Participants with onboard experience did make the same judgment more than participants with no onboard experience. Conclusion: In marine collision situations, maritime officers tend to avoid collisions by adjusting only the direction of their ships, and this tendency is more pronounced among maritime officers with onboard experience. The effect of the method of information representation on their judgment was not significant. Application: The results of this research might help to train maritime officers for safe navigation and to design a collision avoidance support system.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.4 no.3 s.8
• /
• pp.61-72
• /
• 2005

This paper is designed to report the results of response manual development in relation to the freeway Incident Management System(FIMS) development as part of Intelligent Transportation Systems Research and Development program. The central core of the FIMS is an integration of the component parts and the modular, but integrated system for freeway management. The whole approach has been component-orientated, with a secondary emphasis being placed on the traffic characteristics at the sites. The first task taken during the process was the selection of the required actions for each step within the Incident Management System. After through review and analysis of existing incident response procedures and manuals, the incident response manual led to the utilization of different technologies and actions in relation to the specific needs and character of the incidents. FIMS also provides Integrated Incident Management according to the verified incident information provided by the each components The deployment of containment and mitigation strategies for incidents will be automatic or manual depending on the configuration of the system. It is anticipated that, over a period of time, operators will be able to response the incident using integrated and organized Procedures and action items.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2003.04a
• /
• pp.349-353
• /
• 2003

최근 관심이 증대되고 있는 국토모니터링과 관련하여 기존의 SPOT, IRS, KOMPSAT, LANDSAT 등의 중ㆍ저해상도 위성영상과 IKONOS 등의 고해상도 위성영상을 이용하여 국토의 변화를 탐지하고자 하는 시도가 활발히 진행되고 있다. 이 때 영상의 기하보정은 필수적인 과정이며 영상의 기하보정시 기준점을 취득하는 과정에 많은 시간과 작업비용이 소요된다. 현재 기준점 취득은 수치지도 등을 통해 기존의 지상기준점을 이용하는 방법과 GPS를 이용한 현지 측량방법이 활용되고 있는데 동일지역에 대해 매번 사업 때마다 수행되고 있는 실정이다. 따라서 이러한 과정을 보다 효율적으로 수행하기 위한 하나의 방안으로 본 연구에서는 image chip을 이용하여 GCP를 취득하고 이를 데이터베이스로 구축하여 기존의 작업을 자동화, 체계화하고자 하였다. 이를 통하여 중복측량 방지와 데이터의 균질성을 기할 수 있었다. Image Chip의 영상 정합을 위해서는 상관계수법과 최소제곱정합법을 이용하여 부영상소 단위까지 정합결과를 얻을 수 있었으며 위성의 header 정보로부터의 영상의 표정각과 입사각에 대한 정보를 이용하여 축척과 회전요소를 고려함으로써 영상 정합시 보다 정확한 기준점 정보를 취득할 수 있었다. 또한, 이종 센서간 영상정합 가능성에 대해서 연구한 결과 KOMPSAT과 SPOT간에는 신뢰할 만한 수준의 정합 결과를 얻을 수 있었으나 고해상도 영상의 경우에는 항공사진과 IKONOS의 영상 정합시 센서의 방사학적 특성의 차이로 신뢰할 안한 결과를 얻을 수 없었다. 영상 정합시 정확도에 영향을 미치는 인자들에 관한 실험 결과 센서의 파장, 계절, Chip 영상의 크기 등이 큰 영향을 미쳤으며 영상정합을 위해 영상 GCP를 데이터베이스에서 검색할 때 이에 대한 고려가 우선적으로 이루어져야 할 것으로 사료된다.n of hub-and-spoke system, integration of logistics bases, introduction of (automatic) parking building, diversification of transportation mode, and etc. At the same time, we constructed three practically executable scenarios based on those ideas. The first is "Center Hub" scenario, the second is "Metropolitan Hub" scenario. The third and last scenario is "Regional Consolidation of Warehouses (distribution centers)".f worldly desire' and 'cordiality' that one could be deserved his diligency becoming a part of the harmonious idealistic living place. Fourthly, on the character of story teller. Originally he is a incomer of "Gang-Ho" from real world. so that reason, he is showing dualism not to deny the loyalty oath to his king, while he intends to satisfy with the life in "Gang- Ho" separating himself from real world. As a gentry, at that time, the loyalty oath is inevitable one and that is found from wr