• Journal of the Korean Institute of Intelligent Systems
• /
• v.25 no.6
• /
• pp.536-541
• /
• 2015

In this paper, we propose a the image-based automatic flight control system for the mini drone. Automatic flight system with a camera on the ceiling and markers on the floor and landing position is designed in an indoor environment. Images from the ceiling camera is used not only to recognize the makers and landing position but also to track the drone motion. PC sever identifies the location of the drone and sends control commands to the mini drone. Flight controller of the mini drone is designed using state-machine algorithm, PID control and way-point position control method. From the, The proposed automatic flight control system is verified through the experiments of the mini drone. We see that known makers in environment are recognized and the drone can follows the trajectories with the specific ㄱ, ㄷ and ㅁ shapes. Also, experimental results show that the drone can approach and correctly land on the target positions which are set at different height.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2002.11a
• /
• pp.121-126
• /
• 2002

This paper introduces a method that can get information for the movement of a spreader and skew in order to drive ALS(Automatic Landing System) in the crane used at the harbor. Some methods that use 3D laser scanner sensor or laser range finder to obtain the information in ALS are used presently. But these have some defects respectively in economical efficiency and performance. Therefore, to recover these defects, we propose a method acquiring the information for the movement of a spreader and skew using CCD camera for image processing and laser range finder

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.6
• /
• pp.608-614
• /
• 2008

This paper describes a location tracking system to guide landing process of an Unmanned Helicopter(UMH) exploiting MIT Cricket nodes. For automatic landing of a UMH, a precise positioning system is indispensable. However, GPS(Global Positioning System) is inadequate for tracking the three dimensional position of a UMH because of large positioning errors. The Cricket systems use Time-Difference-of-Arrival(TDoA) method with ultrasonic and RF(Radio Frequency) signals to measure distances. They operate in passive mode in that a listener attached to a moving device receives distance signals from several beacons located at fixed points on ground. Inevitably, this passive type of implementation causes large disturbances in measuring distances between beacons and the listener due to wind blow from propeller and turbulence of UMH body. To cope with this problem, we proposed active type of implementation for positioning a UMH. In this implementation, a beacon is set up at UMH body and four listeners are located at ground area at least where the UMH will land. A pair of Ultrasonic and RF signals from the beacon arrives at several listeners to calculate the position of the UMH. The distance signals among listeners are synchronized with a counter value appended to each distance signals from the beacon.

• Journal of Convergence for Information Technology
• /
• v.7 no.3
• /
• pp.27-36
• /
• 2017

In almost industries, such as the logistics industry, marine fisheries, agriculture, industry, and services, small unmanned aerial vehicles are used for aerial photographing or closing flight in areas where human access is difficult or CCTV is not installed. Also, based on the information of small unmanned aerial photographing, application research is actively carried out to efficiently perform surveillance, control, or management. In order to carry out tasks in a mission-based manner in which the set tasks are assigned and the tasks are automatically performed, the small unmanned aerial vehicles must not only fly steadily but also be able to charge the energy periodically, In addition, the unmanned aircraft need to land automatically and precisely at certain points after the end of the mission. In order to accomplish this, an automatic precision landing method that leads landing by continuously detecting and recognizing a marker located at a landing point from a video shot of a small UAV is required. In this paper, it is shown that accurate and stable automatic landing is possible even if simple template matching technique is applied without using various recognition methods that require high specification in using low cost general purpose small unmanned aerial vehicle. Through simulation and actual experiments, the results show that the proposed method will be made good use of industrial fields.

• Journal of Advanced Navigation Technology
• /
• v.17 no.3
• /
• pp.279-284
• /
• 2013

Among the phases of flight operations pilots feel much pressure in landing segment. There is a number of factors affecting landing safety while pilots reduce aircraft speeds and make a touchdown and stop completely. If runway length is sufficient for landing, there maybe is no problem. But it is not the case all the time. So it is necessary to confirm whether landing performance is within limits or not. Required landing distance is actual landing distance demonstrated by flight test pilot plus allowances for average airline pilots. FAR(Federal Aviation Regulations) AFM certification is based upon manual landing for dry and wet runway. Other runway conditions are not the certification basis. JAR dictates even contaminated/slippery runway is included by prescribed allowances. Automatic landing is not certification basis, so actual landing distances are provided. In this paper I would like to analyze distance allowances included in each type of runway condition. In addition there is no regulation about allowances for specific runway condition, I would suggest adequate allowances for that case.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.3
• /
• pp.207-212
• /
• 2010

This paper presents a spiral descending path and a landing guidance law for net-recovery of a fixed-wing unmanned aerial vehicle. The net-recovery landing flight is divided into two phases. In the first phase, a spiral descending path is designed from an arbitrary initial position to a final approaching waypoint toward the recovery net. The flight path angle is controlled to be aligned to the approaching direction at the end of the spiral descent. In the second phase, the aircraft is guided from the approaching waypoint to the recovery net using a pseudo pursuit landing guidance law. Six degree-of-freedom simulation is performed to verify the performance of the proposed landing guidance law.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1276-1279
• /
• 1996

Reclaimer in the raw material yard is being used to dig iron and coal so that they transfer to main blast furnace. A newly automatic system was developed and tested in the raw yard of Kwangyang iron making. The concept of the proposed system is based on the 3-dimensional detection of pile and auto-landing on the surface it.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.2
• /
• pp.81-99
• /
• 1994

최근 항공기 착륙시스템을 자동화하려는 노력이 활발히 진행되고 있다. 제어이론의 발달에 따라 최적제어, 적응제어, 지능제어와 같은 최신제어이론을 적용하여 Blind Landing System의 개발에 박차를 가하고 있다. 본 연구에서는 ILS로부터 나오는 신호를 받아 정해진 Glide Path를 추종하고 또한 일정고도에 도달하면 플래어하여 안전하게 접지할 수 있도록 하는 제어시스템을 개발하고자 항공기의 자동착륙시스템을 위한 제어기법들을 연구하였다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.3
• /
• pp.262-269
• /
• 2005

Automatic landing of UAVs receives increasing interest these days, with increasing number of the developed UAV systems. In this paper, a glidepath tracking algorithm of the subscale UAV was proposed and the performance was analyzed. Flight data analysis shows that the existing autolanding flight control algorithm has a classical type glidepath control. This paper presents an alternative glidepath tracking strategy based on embedded flight control law. The performance of the proposed strategy was investigated through the TDP(Touch Down Point) error analysis with regard to various flight environment: steady headwind, atmospheric disturbance, communication transfer delay. It was verified that the proposed glidepath tracking strategy can be successfully applied to the practical autolanding of UAV systems.

• Proceedings of the KIEE Conference
• /
• 2006.04a
• /
• pp.339-341
• /
• 2006

This paper proposes a method of container position measurement using automatic landing system that is estimated by a laser range finder. In the most of container position measurement methods, CCD cameras or laser scanners have been used to get the source data. However those sensors are not only weak for disturbances, for examples, the light, fog, and rain, but also the system cost is high. When the spreader arrives the goal position, it is still swung by inertia or by wind effect. In this paper, the spreader swung data have been used to find the container position. The laser range finder is equipped in the front side of spreader. It can measure distance and relative position between spreader and container. This laser range finder can be rotated as desired by a motor. And a tilt sensor is equipped on the spreader to measure spreader sway. We estimate the relative position information between the spreader and a container using the laser range finder and tilt sensor through the geometrical analysis.