• Structural Engineering and Mechanics
• /
• v.65 no.2
• /
• pp.129-139
• /
• 2018

Post-tensioning (PT) tendons are commonly used for the assembly of modularized concrete members, and tension is applied to the tendons during construction to facilitate the integrated behavior of the members. However, the tension in a PT tendon decreases over time due to steel corrosion and concrete creep, and consequently, the stress on the anchor head that secures the PT tendon also diminishes. This study proposes an automatic detection system to identify tension reduction in a PT tendon using pulsed-eddy-current (PEC) measurement. An eddy-current sensor is installed on the surface of the steel anchor head. The sensor creates a pulsed excitation to the driving coil and measures the resulting PEC response using the pick-up coil. The basic premise is that the tension reduction of a PT tendon results in stress reduction on the anchor head surface and a change in the PEC intensity measured by the pick-up coil. Thus, PEC measurement is used to detect the reduction of the anchor head stress and consequently the reduction of the PT tendon force below a certain threshold value. The advantages of the proposed PEC-based tension-reduction-detection (PTRD) system are (1) a low-cost (< $ 30), low-power (< 2 Watts) sensor, (2) a short inspection time (< 10 seconds), (3) high reliability and (4) the potential for embedded sensing. A 3.3 m long full-scale monostrand PT tendon was used to evaluate the performance of the proposed PTRD system. The PT tendon was tensioned to 180 kN using a custom universal tensile machine, and the tension was decreased to 0 kN at 20 kN intervals. At each tension, the PEC responses were measured, and tension reduction was successfully detected.

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.4
• /
• pp.1122-1131
• /
• 2000

The efficiency of thesytem depends upon an accurate extraction capability of index terms in the system of information search or in that of automatic index. Therefore, extraction of accurate index terms is of utmost importance. This report presents the generation methods of composition noun for efficient index term extraction by using words of high frequency appearance, so that the right documents can be found during information search. For the sake of presentation of this method, index terms of composition noun shall be extracted by applying the rule of composition and disintegration to the nouns with high frequency of appearance in the documents, such as those with upper 30%∼40% of frequency ratio. In addition, for he purpose of effecting an inspection of validity in relation to a composition of high frequency nouns such as those with upper 30∼40% of frequency ratio as presented in this report, it proposes an adequate frquency ratio during noun composition. Based upon the proposed application, in this short documents with less than 300 syllables, low frequency omissions were noticed, when composed with nouns in the upper 30% of frequency ratio; whereas the documents with more than 30 syllables, when composed with nouns in he upper 40% of frequency ration, had a considerable reduction of low frequency omissions. Thus, total number of index terms has decreased to 57.7% of these existing and an accurate extraction of index terms with an 85.6% adequacy ratio became possible.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.451-459
• /
• 2016

Crack detection on panels during manufacturing process is an important step for ensuring the product quality. The accuracy and efficiency of traditional crack detection methods, which are performed by eye inspection, are dependent on human inspectors. Therefore, implementation of an on-line and precise crack detection is required during the panel pressing process. In this paper, a regular CCTV camera system is utilized to obtain images of panel products and an image process based crack detection technique is developed. This technique uses a comparison between the base image and a test image using an amplitude mapping of the local image. Experiments are performed in the laboratory and in the actual manufacturing lines to evaluate the performance of the developed technique. Experimental results indicate that the proposed technique could be used to effectively detect a crack on panels with high speed.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.4
• /
• pp.341-350
• /
• 2008

Change detection has been recognized as one of the most important steps to update city models. In this study, we thus propose a method to detect urban changes from two sets of LIDAR data acquired at different times. The main processes in the proposed method are (1) detecting change areas through subtraction between two DSMs generated from the LIDAR sets, (2) organizing the LIDAR points within the detected areas into surface patches, (3) classifying the class of each patch such as ground, vegetation, and building, and (4) determining the kinds of changes based on the properties and classes of the patches. The results which were obtained from the application of the proposed method to real data were verified as appropriate using the reference data manually acquired from the visual inspection of the orthoimages of the same area. The probability of success in change detection is assessed to 97% on an average. In conclusion, the proposed method is evaluated as a reliable, and efficient approach to change detection and thus the update of city model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2744-2748
• /
• 2015

This paper analyzes the effect on productivity by measuring Function Point per MM(man-month) in a software development project and code inspection which performed in Agile methodology, and introduce the method of applying MDA/MDD technology in the e-government standard framework project. MDA/MDD which recently raising its head is technology that increase software development productivity through automatic transformation form abstract model into lower abstract model, or from model to code. but, many Lessons obtained through the case studies, the analysis suggests a limited effect measurements. In this study, efficient development methodology and utilizing a e-government framework to measure the effectiveness of the MDD to the new measures through a case study applied to real information system development process. In addition to, managing information modeling through integrated repository presents a traceability and visibility.

• Fire Science and Engineering
• /
• v.32 no.5
• /
• pp.57-66
• /
• 2018

A sports center fire in Jecheon that caused 29 deaths and 40 injuries was analyzed based on initial response and management in order to investigate the causes of the casualties. The aspects of initial response included delay of reporting 119, not being guided to the exit for the body scrubber on the $2^{nd}$ floor for escape, opening the fire doors of the exits on the $1^{st}$ floor and $3^{rd}$ floor, not closing the fire door of the main stairs on the $3^{rd}$ floor, and not doing an emergency broadcast. The management aspects included closing the alarm valve of the sprinkler system on the $1^{st}$ floor, starting-stop of the fire pump controller, neglecting leakage of water and electricity between the false ceiling and ceiling in the parking lot, hiding the exit light in the ladies bathroom lounge on the $2^{nd}$ floor and piling up things in the exit, neglecting the button of an automatic door on the $2^{nd}$ floor, conventional fire safety management, insufficient inspection of fire equipment, and not working fire shutters and smoke exhaust windows.

• Journal of Environmental Science International
• /
• v.19 no.6
• /
• pp.747-753
• /
• 2010

It follows in quality and sewage exclusion method of the investigation objective sector and the Combined Sewer Overflows which is suitable in regional characteristics and the confluence area against the rainfall initially a flow and the medulla and measurement - it analyzes the initial rainfall outflow possibility control plan which is suitable in the domestic actual condition and it proposes the monitor ring plan for the long-term flow and pollution load data accumulation. From the research which it sees the Infiltration water/Influent water and CSOs investigation it passes by the phase of hazard chain and Namwon right time 4 it does not hold reverse under selecting, Measurement it used the hazard automatic flow joint seal Sigma 910 machine and in case 15 minute interval of the I/I, it measured a flow at case 5, 15 minute standing of the CSOs. The water quality investigation for the water leakage investigation of the I/I and the sewage from the point which is identical with flow measurement during on-the-spot inspection duration against 6 items which include the BOD sampling and an analysis, when the rainfall analysis for CSOs fundamental investigation analyzed against 18 items which include the BOD sampling. Consequently, for the optimum interpretation invasion water / inflow water of the this investigation area day average the lowest flow - water quality assessment veterinarian optimum interpretation hazard average per day - lowest flow - it averages a medulla evaluation law department one lowest flow evaluation technique and it selects, it presentation collectively from here it gets, position result with base flow analysis of invasion water / inflow water.

• Journal of Digital Convergence
• /
• v.13 no.1
• /
• pp.269-274
• /
• 2015

According to the development of IT industry, prevalence of AOI equipment is spreading, and also requiring the high resolution of the camera used in the equipment. The weight of the camera is increased to obtain a high resolution, and thus increases the vibration displacement is a problem occurring in the picturing, camera motion control also becomes difficult. In this study, using a finite element analysis program NX/NASTRAN, the transient response of the camera was analysed which is subjected to an impact force due to inertia. The finite element analysis result is correlated with laser interferometer measurement. When AOI equipment is restructuring, the correlated finite element analysis model can be used to verify the authenticity of the new design.

• Journal of Pharmaceutical Investigation
• /
• v.37 no.6
• /
• pp.329-338
• /
• 2007

The quality assurance issue of drug products is more important than the general product because it is highly related to the human health and life. In this reason, the regulatory guide lines have continuously been intensified all around the world. In order to achieve effective quality assurance and real-time product release (RTPR) of drug products, process analytical technology (PAT), which can analyze and control a manufacturing process, has been proposed from the United States. With the PAT process, we can obtain significant process features of materials, quality characteristics and product capabilities from a raw material to the final product in the real-time procedure. PAT can also be utilized to process validation using information system that can analyze the risk of drug products through out an entire product life-cycle. In this paper, we first offered a new concept for the off-line process design methods to prepare the improved quality assurance restrictions and a real-time control method by establishing an information system. We also introduced an automatic inspection system by obtaining surrogate variables based on drug product formulations. Finally, we proposed an advanced PAT concept using validation and feedback principles through out the entire life-cycle of drug product manufacturing processes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.11
• /
• pp.4509-4514
• /
• 2010

In this thesis, the effect of switch maintenance improvement is confirmed after testing and operating the switch monitoring system that were researched and developed originally in order to improve method of electric switch maintenance. However, as in an automatic interlocking station where a ground crew was not placed, repair and inspection could not be carried out until the maintenance person comes in case of switch problems or maintenance. In order to improve this issue, control module was installed in a monitoring system which can communicate through a data radio to a remote computer. Thus, the monitoring device can receive control information which a remote computer commands during the operation of switches. Afterward, it shows information on the real-time status of swith, in particular, anomaly situation through user interface after the switch is operated. By improving performance of the monitoring system in this way which can be managed and controled at a remote place, the prompt countermeasure system in case of disruption will be built and as a result, efficiency and convenience of maintenance improvement will be expected to increase.