• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3326-3334
• /
• 1994

To theoretically predict knock occurrence in S. I. engine as a function of engine design and operating parameters, transient local temperature and pressure, mixture density of flame front in combustion period are calculated. We next determined normal combustion period and auto ignition period of end gas using the prediction method on occurrence of spark knock which we suggested. We predict knock occurrence in S. I. engine by comparing consecutively normal combustion period with the auto ignition period of end gas in combustion period. Engine design and operating parameters such as compression ratio, engine speed, spark timing, inlet temperature and pressure are taken into account in this calculations. The predicted result are well matched with the experimental results in turbocharged engine. Therefore, this method will provide the systematic guideline for designing engines in view of knocking limits.

• 한국안전학회지
• /
• 제24권2호
• /
• pp.42-47
• /
• 2009

The flash point and the AIT(auto-ignition temperature) are the most important combustible properties used to determine the potential for the fire and explosion hazards of flammable material. In order to know the accuracy of data in MSDS(Material Safety Data Sheet), the flash point of n-acids were measured by using Pensky-Martens closed cup tester(ASTM D93), Setaflash closed cup tester(ASTM D3278), Tag open cup tester(ASTM D1310) and Cleveland open cup tester(ASTM D92). Also, the AIT of n-acids were measured by using ASTM E659-78 tester. The measured the flash points and the AIT were compared with literatures and MSDS in KOSHA. The measured the flash points and the AIT were different from those in literatures and MSDS. Therefore, This paper shows that it is needed to investigate the MSDS compatibility of n-acids for the fire safety objectives.

• 한국화재소방학회논문지
• /
• 제30권1호
• /
• pp.24-30
• /
• 2016

자연발화 특성은 가연성물질의 취급 및 화재예방을 위한 중요한 인자이다. 본 연구는 ASTM D2155식 발화온도 측정장치를 사용하여 Ethylene Glycol과 물을 혼합한 시료의 자연발화 특성을 고찰하였다. Ethylene Glycol 100%는 시료량 $75{\mu}l{\sim}160{\mu}l$의 범위에서 $434^{\circ}C$로 나타났다. 물을 첨가하여 Ethylene Glycol 80%와 물 20%를 혼합한 시료는 시료량 $100{\mu}l{\sim}125{\mu}l$의 범위에서 $434^{\circ}C$로 나타났고, Ethylene Glycol 60%와 물 40%를 혼합한 시료에서 시료량 $120{\mu}l{\sim}160{\mu}l$의 범위에서 $437^{\circ}C$로 나타났다. 또한 순간발화온도는 시료량 $125{\mu}l$에서 각각 $579^{\circ}C$, $595^{\circ}C$ 및 $611^{\circ}C$를 구하였으며, 물의 비율이 증가할수록 자연발화온도와 순간발화온도는 증가되는 것으로 나타났다.

• 한국추진공학회지
• /
• 제4권4호
• /
• pp.50-58
• /
• 2000

본 연구에서는 RDX가 함유된 HTPB/AP/Al 추진제내에 Ag선을 단선 삽입하여 RDX 함량(0~20%)에 따른 추진제 연소속도와 Ag선 0.15mm를 삽입하였을 때 금속선과 인접한 추진제의 연소속도($r_w$)의 변화를 살펴보았고, RDX 10%가 함유된 추진제를 대상으로 금속선 3종(Ag, Cu, Ni-Cr선)을 직경(0.1~0.6mm)별로 $r_w$/$r_{sb}$와 압력지수(n)의 변화를 고찰하였다. 금속선을 삽입한 RDX를 함유한 니트라민계 추진제의 경우 직경이 0.1 mm인 Ag선을 삽입하였을 때 연소속도 증가비가 압력 1000psia에서 5.94배로 RDX를 함유하지 않은 HTPB/AP추진제의 경우에 비해 약 16.4% 크게 나타났으며, 그 이유는 니트라민계 추진제의 자연발화온도가 상대적으로 낮기 때문이라 판단된다. 또한 금속선의 물리적 성질인 열확산 계수, 녹는점, 직경, 추진제의 열역학 특성치인 연소기체 불꽃온도, 추진제의 자연발화 온도와 연소속도가 $r_w$에 영향을 주는 인자로 고려하여 무차원해석에 의한 실험식을 도출한 결과($r_{wc}$-$r_{we}$)/$r_{we}$ 절대값의 표준편차는 6.11%로 기존의 3개의 무차원군을 사용한 경우의 표준편차보다 17.5% 작아짐을 알 수 있었다.

• 한국가스학회지
• /
• 제16권3호
• /
• pp.8-15
• /
• 2012

이소프로필 알코올의 안전한 취급을 위해 $25^{\circ}C$에서 폭발한계를 고찰하였고, 실험장치를 이용하여 하부인화점, 상부인화점, 연소점 그리고 발화지연시간에 의한 발화온도를 측정하였다. 그 결과, 공정의 안전을 위한 이소프로필 알코올의 폭발 하한계는 2.0 vol%이고, 상한계는 12.0 vol%로 문헌을 통해 판단되었다. 하부인화점은 밀폐계에서 $12{\sim}14^{\circ}C$와 개방식에서 $18{\sim}19^{\circ}C$이었고, 상부인화점은 $38^{\circ}C$로 측정되었다. ASTM E659 장치를 사용하여 측정된 최소자연발화온도는 $463^{\circ}C$이었다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.179-182
• /
• 2014

A comparative DNS study of the ignition characteristics of dual-fueled reactivity controlled compression ignition (RCCI) and stratification charge compression ignition (SCCI) is investigated using a 116-species reduced primary reference fuel (PRF) mechanism. In the RCCI combustion, two PRF fuels (n-heptane and iso-octane) with opposite autoignition characteristics are separatedly supplied and in-cylinder blended such that spatial variations in fuel reactivity, fuel concentration and temperature are achieved. In the SCCI combustion, however, just a single fuel (PRF50) is used such that only fuel concentration and temperature inhomoginieties are obtained. Because three factors, rather than only two as in SCCI combustion, govern the overall RCCI combustion, combustion timing and combustion duration or heat release rate of RCCI combustion are flexibly and effectively controlled. It is found that the overall RCCI combustion occurs much earlier and its combustion duration is longer compared to SCC combustionI. Moreover, the negative temperature coefficient (NTC) has a positive effect on enhancing RCCI combustion by inducing a shorter combustion timing and a longer combustion duration as a result of the occurrence of a predominant low-speed deflagration-combustion mode.

• 한국위험물학회지
• /
• 제6권2호
• /
• pp.23-29
• /
• 2018

The fire and explosion properties necessary for waste, safe storage, transport, process design and operation of handling flammable substances are lower explosion limits(LEL), upper explosion limits(UEL), flash point, AIT( minimum autoignition temperature or spontaneous ignition temperature), fire point etc., An accurate knowledge of the combustion properties is important in developing appropriate prevention and control measures fire and explosion protection in chemical plants. In order to know the accuracy of data in MSDSs(material safety data sheets), the flash point of phenol was measured by Setaflash, Pensky-Martens, Tag, and Cleveland testers. And the AIT of phenol was measured by ASTM 659E apparatus. The explosion limits of phenol was investigated in the reference data. The flash point of phenol by using Setaflash and Pensky-Martens closed-cup testers were experimented at $75^{\circ}C$ and $81^{\circ}C$, respectively. The flash points of phenol by Tag and Cleveland open cup testers were experimented at $82^{\circ}C$ and $89^{\circ}C$, respectively. The AIT of phenol was experimented at $589^{\circ}C$. The LEL and UEL calculated by using Setaflash lower and upper flash point value were calculated as 1.36vol% and 8.67vol%, respectively. By using the relationship between the spontaneous ignition temperature and the ignition delay time proposed, it is possible to predict the ignition delay time at different temperatures in the handling process of phenol.

• 대한기계학회논문집
• /
• 제16권1호
• /
• pp.70-76
• /
• 1992

본 연구에서는 수소와 공기의 예혼합기체가 가열된 벽면에 노출되어 있는 경 우의 점화문제를 1차원 비정상상태로 예측하고자 하며 특히, 계산에서 가정하는 화학 반응기구가 갖는 정확성에 관하여 수치해석적으로 고찰하고자 한다.

• 한국안전학회지
• /
• 제30권2호
• /
• pp.21-26
• /
• 2015

For the safe handling of o-cresol, this study was investigated the explosion limits of o-cresol in the reference data. The flash points and AITs(auto-ignition temperatures) by ignition delay time were experimented. The lower flash points of o-cresol by using closed-cup tester were experimented in $77^{\circ}C$ and $80^{\circ}C$. The lower flash points of o-cresol by using open cup tester were experimented in $86^{\circ}C$ and $87^{\circ}C$. This study measured relationship between the AITs and the ignition delay times by using ASTM E659 tester for o-cresol. The AIT of o-cresol was experimented as $495^{\circ}C$. The lower explosion limit(LEL) by the measured the lower flash point for o-cresol was calculated as 1.27 Vol%.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2000년도 제21회 KOSCO SYMPOSIUM 논문집
• /
• pp.24-32
• /
• 2000

A brief introduction is given on the conditional moment closure model for turbulent nonpremixed combustion. It is based on the transport equations derived through a rigorous mathematical procedure for the conditionally averaged quantities and appropriate modeling forms for conditional scalar dissipation rate, conditional mean velocity and reaction rate. Examples are given for prediction of NO and OH in bluffbody flames, soot distribution in jet flames and autoignition of a methane/ethane jet to predict the ignition delay with respect to initial temperature, pressure and fuel composition. Conditional averaging may also be a powerful modeling concept in other approaches involved in turbulent combustion problems in various different regimes.