• Journal of Korean Tunnelling and Underground Space Association
• /
• v.19 no.6
• /
• pp.1029-1044
• /
• 2017

The Discrete Element Method (DEM) is one of the useful numerical methods to analyze the behavior of the ground formation by computing the motion and interaction using particles. The DEM has not been applied in civil engineering but also a wide range of industrial fields, such as chemical engineering, pharmacy, material science, food engineering, etc. In this study, to review a performance of the spoke-type earth pressure balance (EPB) shield TBM (Tunnel Boring Machine), the commercial software based on the DEM technology was used. An analysis of the TBM during excavation was conducted according to two pre-defined excavation conditions with the different rotation speed of a cutterhead. During the analysis, the resistant torque at the face of the cutterhead, the compressive force at the cutterhead and shield surface, the muck discharge at the screw auger were measured and compared. Upon the two kinds of excavation conditions, the applicability of the DEM analysis was reviewed as a modelling method for the TBM.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.11
• /
• pp.1659-1663
• /
• 2003

$Al_2O_3$ thin films were grown on H-terminated Si(001) substrates using dimethylaluminum isopropoxide [DMAl: $(CH_3)_2AlOCH(CH_3)_2$], as a new Al precursor, and water by atomic layer deposition (ALD). The selflimiting ALD process by alternate surface reactions of DMAI and $H_2O$ was confirmed from measured thicknesses of the aluminum oxide films as functions of the DMAI pulse time and the number of DMAI-$H_2O$ cycles. Under optimal reaction conditions, a growth rate of ~1.06 ${\AA}$ per ALD cycle was achieved at the substrate temperature of $150\;^{\circ}C$. From a mass spectrometric study of the DMAI-$D_2O$ ALD process, it was determined that the overall binary reaction for the deposition of $Al_2O_3\;[2\;(CH_3)_2AlOCH(CH_3)_2\;+\;3\;H_2O\;{\rightarrow}\;Al_2O_3\;+\;4\;CH_4\;+\;2\;HOCH(CH_3)_2]$can be separated into the following two half-reactions: where the asterisks designate the surface species. Growth of stoichiometric $Al_2O_3$ thin films with carbon incorporation less than 1.5 atomic % was confirmed by depth profiling Auger electron spectroscopy. Atomic force microscopy images show atomically flat and uniform surfaces. X-ray photoelectron spectroscopy and cross-sectional high resolution transmission electron microscopy of an $Al_2O_3$ film indicate that there is no distinguishable interfacial Si oxide layer except that a very thin layer of aluminum silicate may have been formed between the $Al_2O_3$ film and the Si substrate. C-V measurements of an $Al_2O_3$ film showed capacitance values comparable to previously reported values.

• Journal of the Korean Magnetics Society
• /
• v.10 no.4
• /
• pp.171-177
• /
• 2000

Exchange coupling of Co/NiMn bilayers fabricated by RF magnetron sputtering method was studied. We investigated the variation of exchange coupling field (H$\sub$ex/) for different annealing temperature and time. The maximum exchange coupling field was obtained after 13hr annealing at 300 $^{\circ}C$. With respect to deposition sequence, it was demonstrated that NiMn-top bilayers had higher exchange coupling field than NiMn-bottom bilayers. Ta capping layer was shown to be essential in achieving exchange coupling and Auger Electron Spectroscopy (AES) proved that uncapped NiMn/Co bilayers did not have exchange coupling because of oxygen incorporation into film. We also observed the effect of Ta underlayer on exchange coupling. It was found that Ta underlayer had better not be used for attaining higher exchange coupling. XRD analysis showed that Ta underlayer helped bilayers develop texture, but it was not essential to exchange coupling of Co/NiMn bilayers, which is in contrast to NiFe/NiMn system. Furthermore, the NiMn and Co thickness dependence of exchange coupling has been investigated. The exchange coupling strength reached the maximum above 200 ${\AA}$ NiMn thickness and had inversely proportional relation with Co thickness.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.6
• /
• pp.1056-1063
• /
• 2006

Thermal evaporated 10 nm-Ni/l nm-Ir/(or polycrystalline)p-Si(100) and 10 nm-$Ni_{50}Co_{50}$/(or polycrystalline)p-Si(100) films were thermally annealed using rapid thermal annealing fur 40 sec at $300{\sim}1200^{\circ}C$. The annealed bilayer structure developed into Ni(Ir or Co)Si and resulting changes in sheet resistance, microstructure, phase and composition were investigated using a four-point probe, a scanning electron microscopy, a field ion beam, an X-ray diffractometer and an Auger electron spectroscope. The final thickness of Ir- and Co-inserted nickel silicides on single crystal silicon was approximately 20$\sim$40 nm and maintained its sheet resistance below 20 $\Omega$/sq. after the silicidation annealing at $1000^{\circ}C$. The ones on polysilicon had thickness of 20$\sim$55 nm and remained low resistance up to $850^{\circ}C$. A possible reason fur the improved thermal stability of the silicides formed on single crystal silicon substrate is the role of Ir and Co in preventing $NiSi_2$ transformation. Ir and Co also improved thermal stability of silicides formed on polysilicon substrate, but this enhancement was lessened due to the formation of high resistant phases and also a result of silicon mixing during high temperature diffusion. Ir-inserted nickel silicides showed surface roughness below 3 nm, which is appropriate for nano process. In conclusion, the proposed Ir- and Co- inserted nickel silicides may be superior over the conventional nickel monosilicides due to improved thermal stability.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.188-188
• /
• 2000

DLC (Diamond-Like Carbon) 박막은 높은 경도와 가시광선 및 적외선 영역에서의 광 투과도, 전기적 절연성, 화학적 안정성 및 저마찰.내마모 특성 등의 우수한 물리.화학적인 물성을 갖고 있기 때문에 여러 분야의 응용연구가 이루어지고 있다. 이러한 DLC 박막을 제작하는 과정에는 여러 가지가 있으나, 본 연구에서는 ECR-PECVD electron cyclotron resonance plasma enhanced chemical vapor deposition) 방법을 사용하였다. 이것은 최근에 많이 이용되고 있는 방법으로, 이온화률이 높을뿐만 아니라 상온에서도 성막이 가능하고 넓은 진공도 영역에서 플라즈마 공정이 가능한 장점이 있다. 기판으로는 4" 크기의 S(100)를 사용하였고, 박막을 제작하기 전에 진공 중에서 플라즈마 전처리를 하였다. 플라즈마 전처리는 Ar 가스를 150SCCM 주입시켜 5$\times$10-1 torr 의 진공도를 유지시키면서, ECR power를 700W로 고정하고, 기판 bias 전압을 -300 V로 하여 5분 동안 기판을 청정하였다. DLC 박막은 ECR power를 700W. 가스혼합비와 유량을 CH4/H2 : 10/100 SCCM, 증착시간을 2시간으로 고정하고, 기판 bias 전압을 0, -50, -75, -100, -150, -200V로 변화시켜가면서 제작하였다. 이때 ECR 소스로부터 기판까지의 거리는 150mm로 하였고, 진공도는 2$\times$10-2torr 였으며, 기판 bias 전압은 기판에 13.56 MHz의 RF power를 연결하여 RF power에 의해서 유도되는 negative DC self bias 전압을 이용하였다. 제작된 박막을 Auger electron spectroscopy, elastic recoil detection, Rutherford backscattering spectroscopy, X-ray diffraction, secondary electron microscopy, atomic force microscoy, $\alpha$-step, Raman scattering spectroscopu, Fourier transform infrared spectroscopy 및 micro hardness tester를 이용하여 기판 bias 전압이 DLC 박막의 특성에 미치는 영향을 조사하였다. 분석결과 본 연구에서 제작된 DLC 박막은 탄소와 수소만으로 구성되어 있으며, 비정질 상태임을 알 수 있었다. 기판 bias 전압의 증가에 따라 박막의 두께가 감소됨을 알 수 있었고, -150V에서는 박막이 거의 만들어지지 않았으며, -200V에서는 기판 표면이 식각되었다. 이것은 기판 bias 전압과 ECR 플라즈마에 의한 이온충돌 효과 때문으로 판단되며, 150V 이하에서는 증착되는 양보다 re-sputtering 되는 양이 더 많을 것으로 생각된다. 기판 bias 전압을 증가시킬수록 플라즈마에 의한 이온충돌 현상이 두드러져 탄소와 결합하고 있던 수소원자들이 떨어져 나가는 탈수소화 (dehydrogenation) 현상을 확인할 수 있었으며, 이것은 C-H 결합에너지가 C-C 결합이나 C=C 결합보다 약하여 수소 원자가 비교적 해리가 잘되므로 이러한 현상이 일어난다고 판단된다. 결합이 끊어진 탄소 원자들은 다른 탄소원자들과 결합하여 3차원적 cross-link를 형성시켜 나가면서 내부 압축응력을 증가시키는 것으로 알려져 있으며, hardness 시험 결과로 이것을 확인할 수 있었다. 그리고 표면거칠기는 기판 bias 전압을 증가시킬수록 더 smooth 해짐을 확인하였다.인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.113-113
• /
• 2000

직접천이형 wide band gap(3.4eV) 반도체중의 하나인 GaN를 청색 및 자외선 laser diode, 고출력 전자장비 등으로 응용하기 위해서는 낮은 접합저항을 갖는 Ohmic contact이 선행되어야 한다. 그러나 만족할만한 p-type GaN의 Ohmic contact은 아직 실현되고 있지 못하며, 이는 GaN와 접합 금속과의 구체적인 반응의 연구를 필요로 한다. 본 연구에서 앞서 Pt, Pt, Ni등의 late transition metal을 p-GaN에 접합시킨 결과 이들은 접합 당시 비교적 평탄하나 후열 처리과정에서 비교적 낮은 온도에서 기판과 열팽창계수의 차이로 인하여 평탄성을 잃어버리면서 barrier height가 증가한다는 사실을 확인하였다. 따라서 본 연구에서는 이러한 열적 불안정성을 극복하기 위하여 Ni과 Pd를 차례로 증착하고 가열하면서 interfacial reaction, film morphology, Fermi level의 움직임을 monchromatic XPS(x-ray photoelectron spectroscopy) 와 SAM(scanning Auger microscopy) 그리고 ex-situ AFM을 이용하여 밝히고자 하였다. 특히 후열처리에 의한 계면 반응에 수반되는 구성 금속원소 간의 합금현상과 금속 층의 평탄성이 밀접한 관계가 있다는 것을 확인하였다. 이러한 합금과정에서 나타나는 금속원소들의 중심 준위의 이동을 체계적으로 규명하기 위해서 Pd1-xNix와 Pd1-xGax 합금들의 표준시료를 arc melting method로 만들어 농도에 따른 금속원소들의 중심 준위의 이동을 측정하여, Pd/Ni/p-GaN 및 Ni/Pd/p-GaN 계에서 열처리 온도에 따른 interfacial reaction을 확인하였다. 그 결과 두 계가 상온에서 nitride 및 alloy를 형성하지 않고 고르게 증착되고, 열처리 온도를 40$0^{\circ}C$에서 $650^{\circ}C$까지 증가시킴에 따라 계면반응의 부산물인 metallic Ga은 증가하고 있으마 nitride는 여전히 형성되지 않는 것을 확인하였다. 증착당시 Ni이 계면에 있는 Pd/Ni/p-GaN의 경우에는 52$0^{\circ}C$까지의 열처리에 의하여 Ni과 Pd가 골고루 섞이고 그 평탄성도 유지되고 barier height의 변화도 없었다. 더 높은 $650^{\circ}C$ 가열에 의해서는 surface free energy가 작은 Ga의 활발한 편석 현상으로 인해 표면은 Ga이 풍부한 Pd-Ga의 합금층으로 덮이고, 동시에 작은 pinhole들이 발생하며 barrier height도 0.3eV 가량 증가하게 된다. 반면에 증착당시 Pd이 계면에 있는 Ni/Pd/p-GaN의 경우에는 40$0^{\circ}C$의 가열까지는 두 금속이 그들 계면에서부터 섞이나, 52$0^{\circ}C$의 가열에 의해 이미 barrier height가 0.2eV 가량 증가하기 시작하였다. 더 높은 $650^{\circ}C$가열에 의해서는 커다란 pinhole, 0.5eV 가량의 barrier height 증가, Pd clustering이 동시에 관찰되었다. 따라서 Ni과 Pd의 일함수는 물론 thermal expansion coefficient가 거의 같으며 surface free energy도 거의 일치한다는 점을 감안하면, 이렇게 뚜렷한 열적 안정성의 차이는 GaN와 contact metal과의 반응시작 온도(disruption onset temperature)의 차이에 기인함을 알 수 있었다. 즉 계면에서의 반응에 의해 편석되는 Ga에 의해 박막의 strain이 이완되면, pinhole 등의 박막결함이 줄어 들고, 이는 계면의 N의 out-diffusion을 방지하여 p-type GaN의 barrier height 증가를 막게 된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.234-234
• /
• 2010

최근 CMOS 소자 크기가 축소됨에 따라 소스와 드레인 영역에서의 접촉저항을 줄이기 위하여, 실리사이드 공정이 많이 연구되고 있다. 실리사이드 물질로서 NiSi는 낮은 저항률과 낮은 실리콘 소모, 낮은 공정온도, 등의 장점을 가지고 있다. 그러나, 실리사이드 형성으로 인한 나노소자의 소오스/드레인에서정션(junction) 누설전류의 증가는 큰 문제가 되므로 실리콘과 실리사이드 계면의 특성이 중요하다. 본 연구에서는 니켈을 이용한 실리사이드 형성시 계면 활성제인 에틸 요오드를 이용하여 실험을 진행하였다. 금속 유기 전구체인 MABONi을 사용하여 ALD 방식으로 증착 한 니켈 박막과 니켈 핵 형성시 계면활성제인 에틸요오드의 처리 방법에 따른 Ni-silicide 박막의 특성을 비교, 분석하였다. 먼저 자연산화막을 건식식각으로 제거한 뒤, 첫 번째 샘플에서는 10회의 주기로 초기 니켈을 증착한 뒤, 에틸요오드로 니켈의 표면 위를 처리하고, 다시 200회의 주기로 니켈을 증착하였으며, 두 번째는 첫 번째 방식에서 에틸요오드 주입 시 동시에 수소도 함께 주입하였다. 세 번째는 비교를 위해 에틸요오드 처리를 하지 않고 니켈 박막만을 증착 하였다. 이어서, 각 샘플을 급속 열처리 장비에서 $400^{\circ}C$부터 $900^{\circ}C$까지 각각 30sec간 열처리를 진행후, 반응하지 않은 잔여 니켈을 제거한 후, XRD(x-ray diffraction), AES(auger), 그리고 4-point probe 등을 이용하여 형성된 실리사이드의 특성을 분석하였다. 에틸요오드와 함께 수소를 주입한 경우 계면에서의 산소 불순물과 카본 성분이 효과적으로 제거되어 $400^{\circ}C$에서 $2.9{\Omega}/{\Box}$ 의 낮은 면저항을 가지는 NiSi가 형성되었고 모든 온도구간에서 다른 샘플에 비하여 가장 낮은 면저항 분포를 보였다. 이는 분해 흡착된 요오드에 의한 계면 특성 향상과 카본 성분이 포함된 잔여물들이 수소처리에 의해 효율적으로 제거되어 실리사이드의 특성이 향상되었기 때문이다. 계면활성제를 사용하지 않은 경우에는 $500^{\circ}C$에서 NiSi가 형성되었다. 반면에 에틸요오드로만 표면을 처리한 경우에는 니켈과 실리콘 계면에서의 카본 성분에 의하여 silicidation 이 충분히 일어나지 않았다. 이러한 결과는 향후 45nm 이하의 CMOS 공정상에서 소스와 드레인의 낮은 누설전류를 가지고, 접촉저항을 줄이기 위한 니켈 실리사이드 형성에 큰 도움을 줄 것으로 기대된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.155.2-155.2
• /
• 2013

Strain-relaxed SiGe layer on Si substrate has numerous potential applications for electronic and opto- electronic devices. SiGe layer must have a high degree of strain relaxation and a low dislocation density. Conventionally, strain-relaxed SiGe on Si has been manufactured using compositionally graded buffers, in which very thick SiGe buffers of several micrometers are grown on a Si substrate with Ge composition increasing from the Si substrate to the surface. In this study, a new plasma process, i.e., the combination of PIII&D and HiPIMS, was adopted to implant Ge ions into Si wafer for direct formation of SiGe layer on Si substrate. Due to the high peak power density applied the Ge sputtering target during HiPIMS operation, a large fraction of sputtered Ge atoms is ionized. If the negative high voltage pulse applied to the sample stage in PIII&D system is synchronized with the pulsed Ge plasma, the ion implantation of Ge ions can be successfully accomplished. The PIII&D system for Ge ion implantation on Si (100) substrate was equipped with 3'-magnetron sputtering guns with Ge and Si target, which were operated with a HiPIMS pulsed-DC power supply. The sample stage with Si substrate was pulse-biased using a separate hard-tube pulser. During the implantation operation, HiPIMS pulse and substrate's negative bias pulse were synchronized at the same frequency of 50 Hz. The pulse voltage applied to the Ge sputtering target was -1200 V and the pulse width was 80 usec. While operating the Ge sputtering gun in HiPIMS mode, a pulse bias of -50 kV was applied to the Si substrate. The pulse width was 50 usec with a 30 usec delay time with respect to the HiPIMS pulse. Ge ion implantation process was performed for 30 min. to achieve approximately 20 % of Ge concentration in Si substrate. Right after Ge ion implantation, ~50 nm thick Si capping layer was deposited to prevent oxidation during subsequent RTA process at $1000^{\circ}C$ in N2 environment. The Ge-implanted Si samples were analyzed using Auger electron spectroscopy, High-resolution X-ray diffractometer, Raman spectroscopy, and Transmission electron microscopy to investigate the depth distribution, the degree of strain relaxation, and the crystalline structure, respectively. The analysis results showed that a strain-relaxed SiGe layer of ~100 nm thickness could be effectively formed on Si substrate by direct Ge ion implantation using the newly-developed PIII&D process for non-gaseous elements.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.78-78
• /
• 2013

Recently, many platinoid metals like platinum and ruthenium have been used as an electrode of microelectronic devices because of their low resistivity and high work-function. However the material cost of Ru is very expensive and it usually takes long initial nucleation time on SiO2 during chemical deposition. Therefore many researchers have focused on how to enhance the initial growth rate on SiO2 surface. There are two methods to deposit Ru film with atomic layer deposition (ALD); the one is thermal ALD using dilute oxygen gas as a reactant, and the other is plasma enhanced ALD (PEALD) using NH3 plasma as a reactant. Generally, the film roughness of Ru film deposited by PEALD is smoother than that deposited by thermal ALD. However, the plasma is not favorable in the application of high aspect ratio structure. In this study, we used a bis(ethylcyclopentadienyl)ruthenium [Ru(EtCp)2] as a metal organic precursor for both thermal and plasma enhanced ALDs. In order to reduce initial nucleation time, we use several methods such as Ar plasma pre-treatment for PEALD and usage of sacrificial RuO2 under layer for thermal ALD. In case of PEALD, some of surface hydroxyls were removed from SiO2 substrate during the Ar plasma treatment. And relatively high surface nitrogen concentration after first NH3 plasma exposure step in ALD process was observed with in-situ Auger electron spectroscopy (AES). This means that surface amine filled the hydroxyl removed sites by the NH3 plasma. Surface amine played a role as a reduction site but not a nucleation site. Therefore, the precursor reduction was enhanced but the adhesion property was degraded. In case of thermal ALD, a Ru film was deposited from Ru precursors on the surface of RuO2 and the RuO2 film was reduced from RuO2/SiO2 interface to Ru during the deposition. The reduction process was controlled by oxygen partial pressure in ambient. Under high oxygen partial pressure, RuO2 was deposited on RuO2/SiO2, and under medium oxygen partial pressure, RuO2 was partially reduced and oxygen concentration in RuO2 film was decreased. Under low oxygen partial pressure, finally RuO2 was disappeared and about 3% of oxygen was remained. Usually rough surface was observed with longer initial nucleation time. However, the Ru deposited with reduction of RuO2 exhibits smooth surface and was deposited quickly because the sacrificial RuO2 has no initial nucleation time on SiO2 and played a role as a buffer layer between Ru and SiO2.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.244-250
• /
• 1999

MOCVD TiN films were prepared from a new TiN precursor, tetrakis(etylmethylamino)titanium (TEMAT) and ammonia. Deposition of TiN films from a single precursor, TEMA T yielded the growth rates of $70 to 1050\AA$/min, depending on the deposition temperature. Furthermore, the excellent bottom coverage of -90% over $0.35\mu\textrm{m}$ contacts was obtained at $275^{\circ}C$. The addition of ammonia to TEMA T lowered the resistivity of as- deposited TiN film to ~ $800\mu\omega-cm$ from $3500~6000\mu\omega-cm$ and improved the stability of TiN film in air. Examination of the films by Auger electron spectroscopy(AES) showed that the oxygen and carbon contents decreased with the addition of ammonia. However, increasing ammonia flow rate decreased the bottom coverage of TiN films over $0.5\mu\textrm{m}$ contacts, probably due to the high sticking coefficient of intermediate species produced from the gas phase reaction of TEMA T and ammonia. Based on the byproduct gases detected by the quadrupole mass spectrometer (QMS), the transammination reaction was proposed to be responsible for TiN deposition. In addition, XPS analysis revealed that the carbon in the films made from TEMA T and ammonia was metallic carbon, suggesting that $\beta$-hydrogen activation process occurs competitively with the transammination reaction.