• Journal of Korean Association for Spatial Structures
• /
• v.22 no.1
• /
• pp.33-40
• /
• 2022

When the center of stiffness and the center of mass of the structure differ under the seismic load, torsion is caused by eccentricity. In this study, an analysis model was modeled in which the positions of the core and the plane rotation axis of a 60-story torsional atypical structure with a plane rotation angle of 1 degree per floor were different. The structural behavior of the analysis model was analyzed, and the earthquake response behavior of the structure was analyzed based on the time history analysis results. As a result, as the eccentricity of the structure increased, the eccentricity response was amplified in the high-rise part, and the bending and torsional behavior responses were complex in the low-order vibration mode. As a result of the analysis, the maximum displacement and story drift ratio increased due to the torsional behavior. The maximum story shear force and the story absolute maximum acceleration showed similarities for each analysis model according to the shape of the vibration mode of the analysis model.

• Journal of Korean Association for Spatial Structures
• /
• v.21 no.1
• /
• pp.105-112
• /
• 2021

In this paper, the dynamic response was analyzed by performing linear dynamic analysis using historic earthquake loads on twisted-shaped structures and fixed structure among free-form high-rise structures with atypical elevation shape following prior studies. In addition, the dynamic characteristics of the analysis models according to the plane rotation angle of the twisted structure were compared and analyzed. As a result of the analysis, as the plane rotation angle of the twisted structure increased, the interlayer deformation rate increased in the high-rise part of 50th floors or more. The story shear force and the story absolute acceleration were similar in the entire structure. In the case of the story shear force, the response of the twisted shape model was rather reduced in the middle part. As a result of analyzing the dynamic response, the vulnerable layer where the response amplification of the twisted structure occurs was found to be 31st story.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.3
• /
• pp.349-356
• /
• 2011

In this paper, the optimal diagrid angle of atypical tall buildings has been found using diagrid optimization technique which is based on parametric algorithm. A diagrid is a diagonal grid which can be seen among atypical tall buildings and structures which effectively resist horizontal and vertical direction loads. Therefore, it is also the objective of this studyto find the maximum stiffness of atypical tall buildings by optimizing diagrid angle. Moreover, this study touches on both cylindrical and tapered off cylindrical structures, as shown in the examples to check the compatibility of optimum diagrid angle, which effectively resists horizontal deformation on top by optimization algorithm.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.44 no.3
• /
• pp.10-21
• /
• 2021

Recently, the demand for atypical structures with functions and sculptural beauty is increasing in the construction industry. Existing mold-based structure production methods have many advantages, but building complex atypical structures represents limitations due to the cost and technical characteristics. Production methods using molding are suitable for mass production systems, but production cost, construction period, construction cost, and environmental pollution can occur in small quantity batch production. The recent trend in the construction industry calls for new construction methods of customized small quantity batch production methods that can produce various types of sophisticated structures. In addition to the economic effects of developing related technologies of 3D Concrete Printers (3DCP), it can enhance national image through the image of future technology, the international status of the construction civil engineering industry, self-reliance, and technology export. Until now, 3DCP technology has been carried out in producing and utilizing residential houses, structures, etc., on land or manufacturing on land and installing them underwater. The final purpose of this research project is to produce marine structures by directly printing various marine structures underwater with 3DCP equipment. Compared to current underwater structure construction techniques, constructing structures directly underwater using 3DCP equipment has the following advantages: 1) cost reduction effects: 2) reduction of construct time, 3) ease of manufacturing amorphous underwater structures, 4) disaster prevention effects. The core element technology of the 3DCP equipment is to extrude the transferred composite materials at a constant quantitative speed and control the printing flow of the materials smoothly while printing the output. In this study, the extruding module of the 3DCP equipment operates underwater while developing an extruding module that can control the printing flow of the material while extruding it at a constant quantitative speed and minimizing the external force that can occur during underwater printing. The research on the development of 3DCP equipment for printing concrete structures underwater and the preliminary experiment of printing concrete structures using high viscosity low-flow concrete composite materials is explained.

• Journal of Korean Association for Spatial Structures
• /
• v.24 no.2
• /
• pp.75-82
• /
• 2024

Since atypical high-rise buildings are vulnerable to gravity loads and seismic loads, various structural systems must be applied to ensure the stability of the structure. In this study, the authors selected a 60-story twisted-shaped structure among atypical high-rise structures as an analytical model to investigate its structural behavior concerning the outrigger system. The structural analyses were performed varying the number of installed layers and the arrangement of the outrigger system, as well as the placement of the mega column, as design variables. The analysis revealed that the most effective position for the outrigger was 0.455H from the top layer, consistent with previous studies. Additionally, connecting outriggers and mega columns significantly reduced the displacement response of the model. From an economic standpoint, it is deemed efficient to connect and install outriggers and mega columns at the structure's ends.

• Wind and Structures
• /
• v.35 no.4
• /
• pp.255-268
• /
• 2022

Light-weight or low-damped structures may encounter the unsteady galloping instability that occurs at low reduced wind speeds, where the classical quasi-steady assumption is invalid. Although this unsteady phenomenon has been widely studied for rectangular cross sections with one side perpendicular to the incidence flow, the effect of the mean wind angle of attack has not been paid enough attention yet. With four sectional models of different side ratios and geometric shapes, the presented research focuses on the effect of the wind angle of attack on unsteady galloping instability. In static tests, comparatively strong vortex shedding force was noticed in the middle of the range of flow incidence where the lift coefficient shows a negative slope. In aeroelastic tests with a low Scruton number, the typical unsteady galloping, which is due to an interaction with vortex-induced vibration and results in unrestricted oscillation initiating at the Kármán vortex resonance wind speed, was observed for the wind angles of attack that characterize relatively strong vortex shedding force. In contrast, for the wind angles of attack with relatively weak shedding force, an "atypical" unsteady galloping was found to occur at a reduced wind speed clearly higher than the Kármán-vortex resonance one. These observations are valid for all four wind tunnel models. One of the wind tunnel models (with a bridge deck cross section) was also tested in a turbulent flow with an intensity about 9%, showing only the atypical unsteady galloping. However, the wind angle of attack with the comparatively strong vortex shedding force remains the most unfavorable one with respect to the instability threshold in low Scruton number conditions.

• Journal of Korea Entertainment Industry Association
• /
• v.14 no.3
• /
• pp.181-190
• /
• 2020

Asura: The City of Madness, which was released in 2017, attracted great attention even prior to its release with the combination of Director Kim Sung-su, and actors, Jung Woo-sung, Hwang Jung-min, Ju Ji-hoon and Kwak Do-won. Faithful to its genre as a crime film of film noir, Asura: The City of Madness created multi-layered issues by the overthrow of the archetypal hero character and variation of the heroic narrative structure drew diverse interpretations among both critics and viewers alike. This study aims at analyzing the heroic narrative structure of Asura: The City of Madness based on Christopher Vogler's "The Hero's Journey" and examining how the universality and typicality of narrative structures as mentioned by Vogler are applied to this film. Although the universal and typical characteristics of all narrative structures cannot be analyzed through Christopher Vogler's The Hero's Journey, five atypical characteristics could be derived from this film that deviate from the universality mentioned by Christopher Vogler by looking at the characteristics of the heroic narrative structure implemented as Han Do-kyung, the leading character and a "hero," proceeds through the 12 stages. This study examines which variations such atypical characteristics brought to the heroic narrative structures in crime films what has changed in audiences' expectations, and how it could work as an alternate narrative.

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.4
• /
• pp.93-100
• /
• 2020

In this study, structural characteristics were analyzed by combining gravity load and lateral loads such as seismic loads through static analysis of example structures, and the static characteristics of the twisted structure according to the plane rotation angle were also analyzed. Example structures were selected as regular structure, and twisted structures; 1.0, 2.0, and 3.0 degree angle of rotation per story, and static analysis was performed by the load combination case 1 and case 2. As a result the story drift ratio of the twisted-shaped structure also increased as the plane rotation angle per story increased. The eccentricity according to the load combination was the highest in the lower stories of all analysis models, and the eccentricity was found to be larger as the rotation angle decreased. The twisted-shaped structure was more responsible for the bending moment of the column than the regular structure, and the vertical member axial force of all analysis models was almost similar.

• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.97-104
• /
• 2008

Many atypical structures on the roadside are exposed to traffics unshielded posing great danger. One way to shield an atypical structure to secure the occupant safety is to stack energy absorbing material modules in front of the structure. This paper presents the analysis method of module type crash cushion made of EPS blocks using simple energy balance of the car and crash cushion and numerical examples for 0.9ton-500km/h, 0.9ton-60km/h and 0.9ton-70km/h impact are presented. This method gives simple estimation of maximum acceleration, time of crash, whether or not the vehicle stops completely before whole cushion is being crushed. However, since the acceleration and velocity data from the analysis is so crudely spaced that calculation of safety indices such is RA and OIV is not possible. Problem is overcome by using data interpolation. The spline and linear interpolation is introduce and safety analysis is made and the results are compared.

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.1
• /
• pp.61-67
• /
• 2020

In the era of the Fourth Industrial Revolution, Various attempts are being made to converge new industries with IT industry to find new growth engines in the field of IT, maximizing efficiency in terms of productivity. 3D printers are also related to this, and various studies have been conducted worldwide to utilize them in the construction industry. At present, there is an active effort to study atypical structures using 3D printers. The most widely used method is the use of glass panels, however, the additional cost of the manufacturing process and thus the overall project cost cannot be ignored. In addition, the construction of the curvature of the existing two-way curved surface in the conventional flat joint method is not suitable for implementing an amorphous shape. In this paper, we propose an optimized shape through Abaqus analysis of various shapes of Space Truss interior using 3D printing technology using polymer.