• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.389-394
• /
• 1994

The lattice filter formed transfer function has the advantage of computer simulation in the analysis of muffler. The transfer function is derived by using z-transformation for perforated elements in through-flow, cross-flow and reverse-flow type. A computer program for the prediction of the performance of automotive mufflers is developed using the transfer functions for uniform tube, open termination, expansion element, perforated elements, etc. The analytical results are verified by comparing with the experimental results for the transmission loss of a muffer. The effect of geometric configuration change of the muffler was invesigated in order to improve the performance of noise attenuation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1078-1082
• /
• 2002

In this paper, we have studied the dependence of insertion loss of a microstrip stepped impedance lowpass filter with coupled open stubs. Coupling mechanisms in the filter depend not only on the transmission line width of the filter but also the gap width of coupled open stubs and three attenuation poles are created with the proper conditions. Also edge capacitance between open stubs play an important role in having three attenuation Poles. We verify the results by obtaining [S] matrices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.135-138
• /
• 1998

This paper presents the results of measured permittivity of PCB sheet material in the frequency range of 0.1[GHz] - 2[GHz] and temperature range of $25[^{\circ}C]$ - $85[^{\circ}C]$. Microstrip lines with different physical length are implemented to measure the attenuation and phase shift of the signals though these lines. The loss factor of these materials could be obtained with the dielectric constant and the attenuation of the microstrip lines.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.10
• /
• pp.157-162
• /
• 2010

Power line communication, using 25[kV] high voltage of railway catenary, is to provide information which is real-time safety information for train operations and train workers in driving. Lots of noise were occupied in the contact wire by electrical and communication equipments. A signal attenuation was caused characteristics of the contact wire and messenger wire. For relaying communications to transmit information using the contact wire, catenary the noise and signal attenuation were investigated. And the final goal of the study was realized to transmit video information by power line communication on electric railway.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.5
• /
• pp.403-408
• /
• 2004

We suggest new attenuator design and formula using quad spiral shaped defected ground structure (DGS). Series resistors and quarter wavelength transmission line that has a role of inverter have been synthesized for attenuator design and novel attenuator structure using quad spiral shaped DGS is fabricated, the measurements show good agreement with theoretical anticipations. The suggested attenuator could remove peak of insertion loss graph through various attenuation method. The various attenuations are obtained by attached pin-diodes, 10-15dB attenuation leveling is realized for validity of suggested design.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.1
• /
• pp.101-108
• /
• 2019

In this study, the hole-cavity resonance technology and the micro pore stainless chip sintering technology were fused to develop silencers with excellent noise attenuation performance even at fluid pressures exceeding 30 bar for the first time at home and abroad. As a result of this study, the noise attenuation performance was greatly improved as reflection, loss, and resonance were made to occur thousands of times simultaneously when fluids pass through the sintered micro pore stainless steel chip sound absorber. The noise of the gas emitted from the bomb without the silencer was shown to be 125dB. And noise test conducted after installation of the silencer showed the noise of 67dB. Given the study results, the amount of noise was greatly reduced in the sintered silencer.

• ETRI Journal
• /
• v.46 no.4
• /
• pp.716-726
• /
• 2024

An ultrawide stopband lowpass filter is reported using three stepped impedance resonators with high selectivity. The filter extends the stopband frequency range and attenuation, and two quarter-wave open stubs and three circular ground slots are introduced. The lumped and distributed equivalent models are derived and analyzed. The corresponding results are validated experimentally in a fabricated prototype. The prototype lowpass filter has a 3 dB cutoff frequency (f_c) of 2.9 GHz, and the stopband is extended up to 35 GHz (12.07f_c), with an attenuation level better than 20 dB throughout. The passband-to-stopband transition (3 dB-20 dB) bandwidth is 0.18 GHz, and the roll-off factor is 135 dB/GHz at 30 dB. The insertion loss is 0.3 dB at 1.6 GHz. The normalized circuit size of the proposed filter with respect to the guided wavelength is 0.04.

• Journal of the Korean Magnetics Society
• /
• v.14 no.5
• /
• pp.174-179
• /
• 2004

Attenuation of conduction noise through microstrip line attached with the high lossy iron flakes-rubber composites has been investigated in GHz frequencies. Microstrip line was designed with characteristic impedance of 50 $\Omega$ and a length corresponding to the center frequency of 3 GHz. Iron flakes were fabricated by mechanical forging of spherical iron powders using an attrition mill. The fabricated microstrip line shows a ideal propagation characteristics of S$\sub$11/ < -60 dB and S$\sub$21/ = 0 dB. Attaching a noise absorbing sheet on the microstrip line, S$\sub$11/ increases to about -10 dB and S$\sub$21/ decreases to -20～-60 dB depending on the length of absorbing sheet. The calculated power loss is as high as 80% in the frequency range 2～8 GHz. It is suggested that the most critical material parameter is magnetic loss for the enhancement of noise attenuation.

• Journal of the Korean Magnetics Society
• /
• v.17 no.6
• /
• pp.242-245
• /
• 2007

Conduction noise attenuation by composite sheets of high magnetic and dielectric loss has been analyzed by using electromagnetic field simulator which employs finite element method. The simulation model consists of microstrip line with planar input/output ports and noise absorbers (magnetic composite sheets containing iron flake particles as absorbent fillers). Reflection and transmission parameters $(S_{11}\;and\;S_{21})$ and power loss are calculated as a function of frequency with variation of sheet size and thickness. The simulated value is in good agreement with measured one and it is demonstrated that the proposed simulation technique can be effectively used in the design and characterization of noise absorbing materials in the RF transmission lines.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11B
• /
• pp.1534-1539
• /
• 2001

In this paper, effects of soft handoff region on the reverse link capacity of a DS-CDMA cellular system are investigated. The reverse link capacity of a CDMA cellular system is calculated at a given soft handoff region ratio (SHRR) and path loss model. The results show that the reverse link capacity increases by 1 ∼ 4 channels according to the soft handoff region ratio and the path loss model. However, in the case of the path loss model having a large attenuation exponent ($\mu$ = 5) and a small shadowing standard deviation ( $\sigma$ = 6 dB), the reverse link capacity is no more increased by increasing SHRR.