• Journal of the Semiconductor & Display Technology
• /
• v.19 no.1
• /
• pp.42-48
• /
• 2020

As global warming accelerates, eco-friendly electric cars are being developed to reduce carbon dioxide emissions, and power conversion inverters are used to drive motors. Among inverter components, DC-link capacitor is heated by high current usage, which causes problems such as performance and life-saving of inverter. Although metal cases with good thermal performance have been used to solve this problem, it is difficult to apply them in practice due to insulation problems with other parts. In this paper, the Heat-Generation influence factor of DC-link capacitor is analyzed. Variables on heat-generation are set at 3 levels for film width, inductance, and film thickness. Box-Behnken to 13 tests using the design and minimal deviations, e.g. through the experiment three times by each level. The surface of the film k type by attaching the sensor current is measured temperature. Capacitance was set to a minimum level of 200 ㎌ and had a frequency of 16 kHz with Worst case, ambient temperature of 85℃ and a ripple current of 50 Ams was applied. The temperature at the measurement point was collected in the data logger after sampling at 1 minute intervals for 2 hours after saturation with the ambient temperature. This experiment confirmed that setup factors are correlated with heat-generation.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.482-489
• /
• 1999

AC PDP(P1asma Display Pane1)s use the mixture of inert gases to generate a discharge inside the display pixels. Impurities such as CO, $CO_2$ and OH inside discharge region may deteriorate the characteristics of PDP operation during long life time of PDP. Electro-negative gas such as CO can cause the sustain pulse amplitude to rise by attaching electrons which will play an important role in the earlier stage of the discharge. MgO film is used to protect the dielectric layer in AC PDP, and is in contact with the free space of display pixel where it is filled with the inert gas mixture. So, MgO film can be a main source of impurities. In this experiment, we observed the change of impurity generation of various MgO films which were deposited by different methods, by using QMS. (quadropole mass spectrometer) The main impurites were $H_2$, CO and $CO_2$. And with the comparison of the TPD (temperature programmed desorption) result, it can be understood that impurity gases are generated by sputtering of MgO surface not by outgassing. Deposition method had effects on the characteristics of the impurity generation. The MgO film manufactured by e-beam evaporation generated more amount of impurity gases than the MgO films manufactured by sputtering or ion-plating. And also heat treatment of MgO film after deposition decreased the magnitude of impurity gas generation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.27-28
• /
• 2013

This study investigates the effect of a protective layer on the level of carbonation resistance of concrete. For the protective layer, a PE film, bubble sheets, double layered bubble sheets and styroform were placed in a mold before placing the concrete. In addition, PE film was retrofitted by attaching on the surface of the substrate concrete with a glue. Results showed that the carbonation depths of the control concrete were 4.6 mm and 5.2 mm at one week and two weeks exposure in an accelerated carbonation chamber, whereas the concrete with all types of protective layer except PE flim did not allow the ingress of carbon dioxide during the same period.

• The Korean Journal of Ceramics
• /
• v.7 no.1
• /
• pp.20-25
• /
• 2001

PbTiO$_3$ thin films were prepared by low-pressure thermal plasma deposition on (100)Pt/(100)MgO substrates. Mist of source material in which metal alkoxides are dissolved in 2-methoxyethanol was introduced into plasma through heating furnace and deposited onto substrates at $600^{\circ}C$. As-deposited PbTiO$_3$/Pt/MgO thin film prepared at 1.33$\times$10$^4$ Pa was grown epitaxially, but was consisted of many rectangular shaped grains, with many grain boundaries and it was impossible to measure electric properties. As-deposited film prepared at 1.00$\times$10$^4$ Pa showed weak peaks of X-ray diffraction and the film was not grown epitaxially. On the other hand, the film after annealed at $700^{\circ}C$ showed strong diffraction peaks and epitaxial growth was also observed. For annealed film, moreover, no clear grain boundaries were observed. The value of ${\varepsilon}_r$, tan${\delta}$, Pr and Ec of annealed film were 160, 3.2%, 10.4${\mu}$C.cm$^-2$ and 51.2kV.cm$^-1$, respectively. Since the composition, Pb/Ti, measured by EDS attaching to SEM changed point by point, the distribution of composition in annealed film was investigated and found out several relations between composition and electric properties. At stoichiometric composition, Pr and Ec showed the lowest value and they gradually became large as composition deviated from stoichiometric one. Moreover, the value of ${\varepsilon}_r$ became gradually large as the ratio of Ti became high.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.46 no.3
• /
• pp.101-108
• /
• 2023

Although the proportion of coal-fired power generation is decreasing, efficient operating technology is needed to continuously invest in facilities and reduce maintenance costs until it is abolished. Boilers, one of the main facilities of power plants, operate for a long time in harsh environments of high temperature and high pressure. In addition, damage due to deterioration is likely to occur depending on the fuel and tube material used. It is very important to judge soundness because damage caused by deterioration adversely affects facility operation. Previously, replication method was used to analyze the progress of deterioration. In the replication method, pre-treatment such as chemical treatment is performed on the boiler tube in the field, the area is reproduced by attaching a film, and the replicated film is determined by an expert in the laboratory with an expensive microscope. However, this method involves substantial costs and time requirements, as well as the possibility of human errors. To address these issues, we developed a mobile health assessment system in this research. Since it is detachable and takes images in real time, this system enables swift evaluations across a broad range and facilitates the assessment of preprocessing quality. In addition, it was intended to reduce existing human mistakes by developing a degradation classification algorithm using the merger cluster method.

• Journal of Bio-Environment Control
• /
• v.16 no.2
• /
• pp.96-100
• /
• 2007

There was no difference in total light transmissivity of covering materials. But the light transmittance of J-2 in greenhouse was by 78.25 which was higher than any other film. The high light transmittance of J-2 was come from low water condensation and dust attached in film surface. The ultraviolet light of J-3 was completely intercepted. The ultraviolet transmittance rate of others was from 62 to 76%. In no heating oriental melon cultivation, the air temperature in tunnel was 15 to $21^{\circ}C$ higher than outer, and the soil temperature in tunnel was 20 to $25^{\circ}C$ higher than outer. Air temperature and soil temperature of J-2 were higher than any other film.

• Journal of Korea Multimedia Society
• /
• v.19 no.12
• /
• pp.2036-2043
• /
• 2016

The $360^{\circ}$ Virtual Reality (VR) live-action movies are filmed by attaching multiple cameras to a rig to shoot the images omni-directionally. Especially, for a live-action film that requires a variety of scenes, the director of photography and his staff usually have to operate the rigged cameras directly all around the scene and edit the footage during the post-production stage so that the entire process can incur much time and high cost. However, it will also be possible to acquire high-quality omni-directional images with fewer staff if the camera rig(s) can be controlled remotely to allow more flexible camera walking. Thus, a $360^{\circ}$ VR filming system with remote-controlled camera rig has been proposed in this study. The movie producers will be able to produce the movies that provide greater immersion with this system.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.13 no.4
• /
• pp.41-48
• /
• 2017

It is necessary to develop an LED traffic light lens having a snow removal function capable of clearly providing a traffic signal to the driver even when a traffic light is blurred due to heavy snow and wind in the winter season. This study is focused on the research and development of the traffic light lens in the process of developing the LED traffic light with the snow removal function. In the developed traffic light lens, instead of attaching the film heater, the coated nichrome wire was wound into a coil shape and inserted directly into the groove in the lens. The developed heater system facilitates the insertion of the heating wire with high elasticity into a curved lens and can provide a sufficient heat without deformation of the PC lens. The proposed traffic lights were tested in various external environments and the test results showed that complete snow removal is possible without tunnel effect.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.10
• /
• pp.752-757
• /
• 2018

This study presents the performance evaluation results of a 77-GHz waveguide slot array antenna that was fabricated by attaching a patterned printed circuit board(PCB) on a metal block. The 77-GHz waveguide was divided into a top plate and a bottom structure. The top plate was fabricated using a patterned PCB that can implement a fine slot at low cost. The top cover was then bonded to the bottom metal structure with a waveguide trough using anisotropic conductive film. For evaluating the antenna performance, a $1{\times}16$ slot array antenna was fabricated using our proposed method and the gain and pattern were measured and compared with the simulation results. Though the measurement results demonstrate a reduction in gain of around 2.3~3.5 dB compared to the simulation results assuming ideal bonding conditions, the pattern hardly changed and the slot antenna with a gain of approximately 17 dBi at 77 GHz can be easily manufactured at a low cost using the proposed method.

• Journal of Biomedical Engineering Research
• /
• v.35 no.3
• /
• pp.55-61
• /
• 2014

In sleep monitoring system, polysomnography (PSG) is the gold-standard but previous studies revealed that attaching numerous amount of sensors disturb sleep during the test which is the fundamental disadvantage of PSG. We suggest an unconstrained rapid-eye-movement (REM) sleep monitoring method measured with polyvinylidene (PVDF) film-based sensor for the normal and the obstructive sleep apnea (OSA) patients. Nine normal subjects and seventeen OSA patients have participated in the study. During REM sleep, rate and variability of respiration are known to be greater than in other sleep stages. Based on this phenomena, respiratory signals of participants were unconstrainedly measured using the PVDF-based sensor with the PSG and REM sleep were extracted from the average rate and variability of respiration. In epoch-by-epoch REM sleep detection, proposed method classified REM sleep with an average sensitivity of 72.3%, specificity of 92.5%, accuracy of 88.9%, and kappa statistic of 0.60 compared to the results of PSG. Student's t-test showed no significant difference between the results of normal and OSA group. This method is potentially applicable to REM sleep detection in homing environment or ambulatory monitoring.