• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.11
• /
• pp.1014-1021
• /
• 1998

We evaluated the effect of processing variables on microstructural evolution interface irregularity between Ag sheath and superconductor core and resultant critical current density(J$_{c}$) of (Bi,Pb)$_2$Sr$_2$Ca$_2$Cu$_3$O$_{x}$(2223) superconductor tape. The value of J$_{c}$ was significantly influenced by the interface irregularity, degree of texturing and relative 2223 content. The interface became more irregular(sausage effect), while the degree of texturing gradually improved as the dimension of tape decreased during forming process. As the dimension of wire/tape were changed from diameter of 3.25 mm to thickness of 0.20 mm, J$_{c}$ value was observed to be increased by 10 times. In addition, optimum sintering temperature for improved J$_{c}$ was observed to be 835$^{\circ}C$ in a ambient atmosphere probably due to combined effect of both improved texturing and high 2223 content. Microstructural investigation showed the degree of texturing was degraded by the existence of both second phases and interface irregularity. It was observed that larger grain size and better texturing was developed near relatively flat interface compared to those inside superconducting core.ting core.

• Journal of the Korean Ceramic Society
• /
• v.47 no.3
• /
• pp.244-248
• /
• 2010

Porous calcium phosphates were successfully fabricated by using a cuttlefish bone. The cuttlefish bone, which is composed of $CaCO_3$, showed a special porous microstructure containing uniform-sized voids. In this study, the pre-forms infiltrated distilled phosphoric acid were sintered at $1200^{\circ}C$ in an air atmosphere. The porous microstructure of the pre-forms was kept their original pattern after sintering with a synthesis of calcium phosphate. The obtained porous calcium phosphate, sintered at $1200^{\circ}C$ for 3 h at 17% concentration of phosphoric acid, showed uniform open pores of 150 ${\mu}m$ in size and $\beta$-TCP phase in the XRD patterns. Above 16% concentration, CaO phase, derived from the decomposition of $CaCO_3$, decreased gradually in the sintered samples, and the measured Ca/P ratios of the samples prepared from 16% and 18% concentration were 1.67 and 1.43, which are close to stoichiometric HA (1.66) and $\beta$-TCP (1.50).

• Journal of Powder Materials
• /
• v.18 no.4
• /
• pp.365-371
• /
• 2011

In this study, gradient porous Al-Cu sintered body was fabricated by powder metallurgy processing. Al-Cu powder mixtures were prepared by low energy ball milling with various milling time. After ball milling for 3h, the shape of powder mixtures changed to spherical type with size of 100~500 ${\mu}m$. Subsequently, Al-Cu powder mixtures were classified (under 150, 150~300 and over 300 ${\mu}m$) and compacted (20, 50 and 100 MPa). Then, they were sintered at $600^{\circ}C$ for various holding time (10, 30, 60 and 120 min) in $N_2$ atmosphere. The sintered bodies had 32~45% of porosity. As a result, the optimum holding time was determined to be 60 min at $600^{\circ}C$ and sintered bodies with various porosity were obtained by controlling the compacting pressure.

• Journal of the Korean Geophysical Society
• /
• v.4 no.4
• /
• pp.257-266
• /
• 2001

The properties of electrical resistance of Mn-Co-Ni-Fe oxide-based therrnistor with various Fe contents in sintering process at 1200 to 1400℃ for 4 hours in air atmosphere for fabricating therrnistor materials were investigated. The results were as follows: all samples showed single cubic spinel crystal structures in all region. The electrical conductivinity is the highlest thermistor sintered at 1300℃ for 4 hours. In general when the Fe content is increased except F-2, the resistivity increases and relatively the conductivity decreases. Particularly F-2 composition exhibited the highlest electrical conductivity(1.4x $10^-3$$Ω$cm) and relatively low B constant(2906K)

• Korean Journal of Materials Research
• /
• v.12 no.8
• /
• pp.656-660
• /
• 2002

It was investigated that $Al_2$$O_3$/Cu nanocomposite powder could be optimally prepared by dispersion and reduction of Cu oxide, and suitably consolidated by employing pulse electric current sintering (PECS) process. $\alpha$-$Al_2$$O_3$ and CuO powders were used as elemental powders. In order to obtain $Al_2$O$_3$ embedded by finely and homogeneously dispersed CuO particles, the elemental powders were high energy ball milled at the rotating speed of 900 rpm, with the milling time varying up to 10 h. The milled powders were heat treated at $350^{\circ}C$ in H$_2$ atmosphere for 30 min to reduce CuO into Cu. The reduced powders were subsequently sintered by employing PECS process. The composites sintered at $1250^{\circ}C$ for 5 min showed the relative density of above 98%. The fracture toughness of the $Al_2$$O_3$/Cu nanocomposite was as high as 4.9MPa.$m^{1}$2//, being 1.3 times the value of pure $Al_2$$O_3$ sintered under the same condition.

• Journal of the Korean Ceramic Society
• /
• v.28 no.9
• /
• pp.689-695
• /
• 1991

Dielectric properties of Ba1-$\chi$Sr$\chi$Ti1-yCayO3-y ceramics, where Sr and Ca were doped to Ba-site and Ti-site within the range of 0 x 0.24 and 0 y 0.05, respectively, were investigated. The substitution of Ca for Ti, which maintained the high resistivity of these formulations after sintering in a reducing atmosphere, was confirmed. Ca addition decreased the tetragonality c/a, increased the unit cell volume, and lowered Curie temperature, which were attributed to the occupancy of Ca2+ ions on Ti-sites. The lowering of Curie temperature by Ca addition was affected by the substitution of Sr for Ba-site; within 2 mol% of Ca, Curie temperature was lowered at a rate of 2$0^{\circ}C$ and 16$^{\circ}C$ per mol% of Ca at x=0 and x=0.08, respectively. Whereas the resistivity of the formulations without Ca was reduced to 107 {{{{ OMEGA }}cm, when sintered at low oxygen partial pressure of 10-9 MPa, the resistivity value higher than 1011 {{{{ OMEGA }}cm was maintained for the formulations containing Ca more than 0.5 mol%. Dielectric loss factor, tan$\delta$, was about 1% for most formulations.

• Journal of the Korean Ceramic Society
• /
• v.44 no.12
• /
• pp.727-732
• /
• 2007

In order to fabricate a highly performing cathode for low-temperature type solid oxide fuel cells working at below $700^{\circ}C$, electrode microstructure control and electrode polarization measurement were performed with an electronic conductor, $La_{0.8}Sr_{0.2}MnO_3$ (LSM) and a mixed conductor, $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$(LSCF). For both cathode materials, when $Sm_{0.2}Ce_{0.8}O_2$ (SDC) buffer layer was formed between the cathode and yttria-stabilized zirconia (YSZ) electrolyte, interfacial reaction products were effectively prevented at the high temperature of cathode sintering and the electrode polarization was also reduced. Moreover, cathode polarization was greatly reduced by applying the SDC sol-gel coating on the cathode pore surface, which can increase triple phase boundary from the electrolyte interface to the electrode surface. For the LSCF cathode with the SDC buffer layer and modified by the SDC sol-gel coating on the cathode pore surface, the cathode resistance was as low as 0.11 ${\Omega}{\cdot}cm^2$ measured at $700^{\circ}C$ in air atmosphere.

• The Korean Journal of Ceramics
• /
• v.2 no.1
• /
• pp.25-32
• /
• 1996

Solid electroyte nasion was synthesized by the optimized solid state reaction minimizing the volume fraction of secondary $ZrO_2$ and glassy phases. To compensate for the evaporation of Na and P during heat-treatment, excess Na and P were added to the starting composition $Na_{1+x} Zr_2 Si_x P_{d-x} O_{12}$ (x=2.1). Phases pure nasicon comparable in volume fraction to the one obtaied from sol-gel process were synthesized after the reaction at $1100~1150^{\circ}C$,$ P_{O2}>=0.1-0.15 $$ZrO_2$ increased with the heat-treatment time due to the decomposition of nasicon phase and that of glassy phase increased as partial oxygen pressure decreased. The synthesized nasion showed a good electrical conductivity of $-1{\times}10^{-2}({\omega}{\cdot}cm)^{-1}$ at $350^{\circ}C$.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.287-290
• /
• 1989

Single-phase $YBa_2Cu_3O_{j-g}$ (YBC) ceramic samples were annealed at $700^{\circ}C$ under a flowing $O_2$ atmosphere for 0, 18, 36, 54 and 72. hours after sintering. The resistivities(p) and the critical current densities($J_c$) of the samples were measured in a temperature range 77 to 300 K by a four probe method, using silver paint contacts. The variations of the electrical properties with annealing time are explained in terms of flux pinning, percolation probability and randomness, and alignment of grains and twins.The anomalous increases in $J_c$ and $T_c$ observed in sample annealed for a relatively long time possibly due to alignment of grains and twins, may imply the occurrence of superconducting glass state in high-$T_c$ superconducting ceramic.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.572-577
• /
• 2010

Reaction-bonded $Si_3N_4$ has cost-reduction merit because inexpensive silicon powder was used as a start material. But its density was not so high enough to be used for structural materials. So the sintered reaction-bonded $Si_3N_4$techniques were developed to solve the low density problem. In this study the sintered reaction-bonded $Si_3N_4$ manufacturing method by using polymer precursor which recently attained significant interest owing to the good shaping and processing ability was proposed. The formations, properties of reaction-bonded $Si_3N_4$ from silicon and polysilazane mixture were investigated. High density reaction-bonded $Si_3N_4$ was manufactured from silicon and silicon-containing preceramic polymers and post-sintering technique. The mixtures of silicon powder and polysilazane were prepared and reaction sintered in $N_2$ atmosphere at $1350^{\circ}C$ and post-sintered at 1600~$1950^{\circ}C$. Density and phase were analyzed and correlated to the resulting material properties.