• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.3
• /
• pp.267-272
• /
• 2011

The behavior of abrasive wear on counterpart roughness of glass fiber reinforcement polyurethane resin (GF/PUR) composites were investigated at ambient temperature by pin-on-disc friction test. The friction coefficient, cumulative wear volume and surface roughness of these materials against SiC abrasive paper were determined experimentally. The major failure mechanisms were lapping layers, ploughing, delamination, deformation of resin and cracking by scanning electric microscopy (SEM) photograph of the tested surface. As increasing the counterpart roughness the GF/PUR composites indicated higher friction coefficient. The surface roughness of the GF/PUR composites was increased as the sliding velocity was higher and the counterpart roughness was rougher in wear test.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.48 no.3
• /
• pp.277-283
• /
• 2012

The characteristics of abrasive wear on sliding speed of glass fiber reinforcement (GF/PUR) composites were investigated at ambient temperature by pin-on-disc friction test. The cumulative wear volume, friction coefficient and surface roughness of these materials on sliding speed were determined experimentally. The major failure mechanisms were lapping layers, deformation of resin, ploughing, delamination, and cracking by scanning electric microscopy (SEM) photograph of the tested surface. As increasing the sliding speed the GF/PUR composites indicated higher friction coefficient. The surface roughness of the GF/PUR composites was increased as the sliding speed was higher in wear test.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.318-320
• /
• 2009

A switchable Yagi-Uda antenna prototype with radiation pattern reconfiguration is presented in this letter. The proposed reconfigurable antenna is based on the concept of switching between the reflector and director of a Yagi-Uda antenna using a radio frequency PIN diode. As a result, the minimum/maximum radiation can be steered towards desired signals or away from interfering signals in opposite directions. The measured 10 dB impedance bandwidth and gain are 210 MHz (7%) and 8.02 dBi at 3 GHz, respectively. Details of the antenna design and its performance are described and empirically analyzed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.16 no.3
• /
• pp.24-29
• /
• 1992

This paper describes a technique to suppress vibrations of structure under excitation by attaching the hollow rotor partially filled with liquid. The influence of the amount of liquid, number of fins and their widths on absorbing vibration is investigated. The results of experiments are summarized as follows: 1. The effect on suppressing vibration at filling ratio, H over bar = 0.54 is greatest. 2. The viscosity of liquid hardly influence on suppressing vibration. 3. The rotor fitted with two pins having width of pin =(D-$D_f$)/4 is effective generally. 4. The vibration damping effect of the axial fins is greater than that of radial fins.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1124-1125
• /
• 2006

Dry sliding wear behavior of electro-pressure sintered Co-Fe, Co-Ni and Co-Fe-Ni compacts was investigated. Pin-on-disk wear tests were performed on the sintered compacts disk specimens against alumina $(Al_2O_3)$ and silica $(SiO_2)$ ball counterparts at various loads ranging from 3N to 12N. Two sliding speeds of 0.1m/sec and 0.2m/sec and a fixed sliding distance of 1,000m were employed. Worn surfaces and cross sections of them were examined by a scanning electron microscopy, and wear mechanism of the compacts was investigated. Effects of the oxide layer that was formed on wearing surface of the compacts on the wear were also studied.

• International Journal of High-Rise Buildings
• /
• v.8 no.3
• /
• pp.221-227
• /
• 2019

In this paper passive seismic retrofit devices for building structures developed by the author in recent years are introduced. The proposed damping devices were developed by slightly modifying the configuration of conventional devices and enhancing their effectiveness. First a seismic retrofit system consisting of a pin-jointed steel frame and rotational friction dampers installed at each corner of the steel frame was developed. Then two types of steel slit dampers were developed; box-type slit damper and multi-slit damper. In addition, hybrid dampers were developed by combining a slit damper and a friction damper connected in parallel. Finally a self-centering system was developed by using preloaded tendons and viscous dampers connected in series. For each retrofit system developed, an appropriate analytical model was developed, and the seismic performance was verified by loading test and earthquake analysis of case study structures. The experimental and analysis results show that the proposed systems can be used efficiently to enhance the seismic performance of building structures.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.634-641
• /
• 2000

A switchable VCO for DECT handset is designed and fabricated. In dual mode radios, a single VCO is desired to operate at two different frequencies to meet the requirement of two mode(Tx, Rx). The three design types of switchable VCO are switched resonator VCO, switched mode VCO and dual band VCO. In this paper, we use the switched resonator VCO type using pin diode switch to change the total amount of capacitance in the tank circuit. At the bias condition of 3 V and 13mA, the output power and phase noise are better than6.5dBm and -104dBc/Hz at 25khz offset from the carrier, respectively , across the operating frequency range. From these results, the fabricated switched VCO is applicable to the DECT handset.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.5
• /
• pp.821-826
• /
• 1998

Functional properties of mucilage and pigment extracted from Opuntia ficus-indica var. saboten were determined at various temperatures, pHs and alcohol concentrations. The crude mucilage extracted from pickly pear showed pH 4.2, 0.14% total acidity and 8.1% total soluble solid content(w/w, wet basis). Polysaccharide was purified from mucilage extract by isopropanol precipitation. Intrinsic viscosity of polysaccharide was 18.1dl/g and decreased with increasing KCl concentration. Relative viscosity and color stability of mucilage extract were determined with capillary viscometer and spectrophotometer at 534nm, respectively. In additions of 1~20%(v/v) ethanol, the red pigment of mucilage extract was very stable, but relative viscosity, increased gradually. For heating above 7$0^{\circ}C$, the stability of red pigment decreased drastically, but rheological property of mucilage was not changed. During storage, the red pigment was extremely unstable at above pH 8.3. At both pH 3.0 and pH 4.2, the red pigment was the most stable at 4$^{\circ}C$ for 18 days. In the case of storage at 37$^{\circ}C$, pigment of mucilage extract at pH 3.0 was destroyed more quickly than that at pH 4.2. Natural mucilage extract(pH 4.2) showed the good stability of red pigment at 3$0^{\circ}C$ for 10 days.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.270-270
• /
• 2016

We fabricated an organic-inorganic nano laminated encapsulation layer using molecular layer deposition (MLD) combined with atomic layer deposition (ALD). The $Al_2O_3$ inorganic layers as an effective single encapsulation layer were deposited at 80 degree C using ALD with alternating surface-saturation reactions of TMA and $H_2O$. A self-assembled organic layers (SAOLs) were fabricated at the same temperature using MLD. MLD and ALD deposition process were performed in the same reaction chamber. The prepared SAOL-$Al_2O_3$ organic-inorganic nano laminate films exhibited good mechanical stability and excellent encapsulation property. The measurement of water vapor transmission rate (WVTR) was performed with Ca test. We controlled thickness-ratio of organic and inorganic layer, and specific ratio showed a lowest WVTR value. Also this encapsulation layer contained very few pin-holes or defects which were linked in whole area by defect test. To apply into real OLEDs panels, we controlled a film stress from tensile to compressive and flexibility defined as an elastic modulus with organic-inorganic ratio. It has shown that OLEDs panel encapsulated with nano laminate layer exhibits better properties than single layer encapsulated in acceleration conditions. These results indicate that the organic-inorganic nano laminate thin films have high potential for flexible display applications.

• Preventive Nutrition and Food Science
• /
• v.8 no.3
• /
• pp.278-283
• /
• 2003

Textural properties of tofu manufactured with micronized full-fat soyflour (MFS) were enhanced by the addition of soy protein isolate, whey protein concentrate, chitosan oligosaccharide and mushroom powder. The MFS solution (14.2% solid content) was converted to semi-solid tofu by a two-stage heat treatment with the addition of 4% coagulant mix. The MFS tofu was evaluated by a compression test as well as sensory evaluation. To produce the semi-solid gel (MFS tofu) with reasonably high strength and toughness, the MFS solution with 14.2% solid content and 7.0% protein had to be heat treated at 121$^{\circ}C$ for 3min. The relative toughness of MFS tofu was increased by the addition of SPI, showing a 144% increase. The toughness of MFS tofu prepared with the MFS/SPI mixture was greatly increased by the addition of WPC at the level of 0.7% and the water separation from MFS tofu was greatly reduced. Furthermore, the toughness and strength of MFS/SPI tofu was enhanced by the addition of 0.1% chitosan oligosaccharide and 0.2% mushroom powder. The sensory evaluation of the tofu fortified with SPI, chitosan oligosaccharide and mushroom powder was superior to that of MFS tofu, with a higher score for overall preference.