• 항공우주시스템공학회지
• /
• 제13권4호
• /
• pp.43-49
• /
• 2019

고속비행체의 내외부 환경에서 가열이 된 고온고압의 흡열연료를 구현하고, 촉매를 이용한 흡열 열교환기의 성능평가를 가능하도록 하는 시험장치를 설계/제작하였다. 시험장치를 원활히 운용하기 위해, 예비시험을 통하여 고온의 흡열연료를 공급하기 위한 시험절차를 확립하였다. 흡열연료의 공급조건에 따른 촉매성능 시험을 수행하고 흡열량을 분석하였다. 선행연구사례와 동일한 반응조건에서의 촉매 반응결과를 비교하여 시험장치의 타당성을 검증하였다. 본 시험장치는 향후 다양한 조건의 흡열연료와 촉매의 흡열반응 시험에 활용할 수 있다.

• 한국항공우주학회지
• /
• 제33권10호
• /
• pp.75-81
• /
• 2005

낙하물 및 로켓 단분리 등과 같은 비행체 분리물의 궤적을 모사하기 위해 사출, 격자 및 CTS 시험과 같은 풍동시험 기법이 많이 사용된다. 본 논문에서는 3단형 과학로켓 개발 시 사용된 격자 및 CTS 시험 기법 및 대표적인 결과를 소개하였다. 시험에 사용된 풍동은 ONERA S2MA이며 마하수 2.0과 2.8에 대해 13개의 분리 궤적을 시험하였다. 시험 결과는 분리장치를 최적화기 위한 데이터베이스로 활용되었다.

• 한국산학기술학회논문지
• /
• 제16권5호
• /
• pp.3030-3034
• /
• 2015

새로운 엔진과 차량을 개발하여 엔진을 차량에 탑재할 때, 중요하게 고려해야 할 사항 중의 하나는 냉각 성능이다. 만약 냉각 성능이 열악하다면 엔진은 과열되어 파손되게 된다. 그러나 자동차회사에서 일반적으로 엔진은 차량보다 훨씬 빠른 시기에 개발이 진행되게 되어 엔진을 차량에 탑재한 조건에서 냉각 성능을 시험할 수 없다. 본 연구에서는 몇 가지 시험과 계산 결과를 이용하여 엔진의 냉각 성능을 추정하였다. 첫 번째로 엔진의 열정산 시험이 진행되었다. 두 번째로 냉각수 유동 시험이 진행되었다. 이 시험에서 라디에이터로 유입되는 유량을 구할 수 있다. 그리고 차량의 냉각 시험 성능 조건으로부터 차량의 부하와 속도를 구하고, 이로부터 엔진의 토크와 rpm이 계산되었다. 그리고 이러한 결과를 비교하여 엔진의 냉각 성능이 추정되었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1215-1220
• /
• 2001

Wind tunnel test of a new pantograph, that is developed through the KHST project, was performed in RTRI wind tunnel test center of Japan end of last June. This paper indtroduces the measurement results and analysis of noise measurement part that is achieved during the wind tunnel test. The maximum measured sound pressure level at 5m shows 102.3dB(A) at 350km/h and it leads to 88.3dB(A) of predicted sound pressure at 25m that satisfy 91dB(A) of evaluation criteria. Major noise sources of the pantograph was identified as a link between upper and lower arm, panhead contact strips and shunt wires.

• 한국유체기계학회 논문집
• /
• 제4권1호
• /
• pp.30-37
• /
• 2001

The experimental study on the effect of axial clearance between the tip of impeller blades and stationary shroud has been performed. The investigated compressor, which is a part of a small auxiliary power unit engine, consists of a curved inlet, a centrifugal impeller, a channel diffuser and a plenum chamber. It was designed for a total pressure ratio of 4.3 and an efficiency of $77\%$ at design speed of 60,000 rpm. The experiments are carried out in an open-loop centrifugal compressor test rig driven by a turbine. For the four different clearance ratios Cr(clearance/impeller tip width) of 6.25, 10.93, 15.60 and 20.30 percent, the overall performance data are obtained at $97\%,\;90\%$ and $80\%$ of the design speed. The results show the overall pressure ratio decrease of $7.7\%$ and the efficiency loss of $8.7\%$ across the variation of clearance ratio near the design speed. It also indicates that the influence of tip clearance became weaker as the flow rate is reduced and the stable operating range is not significantly influenced by the change of clearance ratio.

• 한국소음진동공학회논문집
• /
• 제23권4호
• /
• pp.301-307
• /
• 2013

MRU(motor reduction unit) for KTX is a assembled complex structure that is equipped with a lot of parts at the express train KTX and that is the core power source operating variable speeds. This study is recorded the dynamic characteristics analysis results tested by EMA which is done through the parts and assembly test, transient analysis and stoped train test in order to design the online monitoring system for KTX MRU. And the mode shapes result from critical vibration frequency explain the relation with variable speeds of express train over 250 km/hr. Also these variable speeds make variable operational frequencies at pinion, axle gear mesh frequency and normal bearing fault frequencies. As the specified speed can make resonance with natural frequencies of the MRU, for the train operating stability, this study also presents the MRU's critical speeds calculated by the each train speed.

• Journal of Mechanical Science and Technology
• /
• 제14권11호
• /
• pp.1232-1243
• /
• 2000

Motor vehicle accidents in rear impacts cause more than fifty percents of drivers to suffer from neck injuries. It is known that most neck injuries are associated with rear-end collisions at a speed lower than 32 km/h and between the Abbreviated Injury Scale (AIS) 1 and AIS 2. Two different types of low speed crash tests such as the frontal barrier and rear moving barrier crashes have been conducted by following the procedure of the Research Committee for Automobile Repairs (RCAR). The injury for the neck and the Head Injury Criteria (HIC) were measured by using the sensors mounted on dummies. We reviewed neck injures and the relationship between the neck and head injuries, and examined the deceleration of the body. Using the experimental test data at the neck, we investigated an improved neck injury criterion Nij. Also, the effects of the position of a head restraint on reducing the frequency and severity of the neck injury in rear-end collisions were investigated.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.228-230
• /
• 2006

While trains perform a complete precision stopping control at stop point, it is essential to keep better commuters comfort in prompt. Because a train's brake force tends to increase a brake effort in a low speed and a low brake effort, a brake force in motor cars must be increased to keep better passenger comfort, to control the special braking qua1ities and to prevent the impact of the automatic coupler rather than trailer's, Rail cars must have a special braking process for the train stopping control. In the train stop mode, the train stopping control is designed to start at 20km/h. It starts by Dynamic brake blending, and then finally stops by only the friction. If these process are not exactly activated, the train may fail a complete precision stop. In this report, it studied the electric and friction brake processing during the precious stopping control. To achieve exact test results, the speed reference has to be reduced the calculated difference. In the precision stopping control. the ways of the keeping brake force in motor car was analyzed and some solutions of controling air pressure was brought up by means of direct test in main line, This study was based on line 5 in Seoul Metropolitan subway.

• Steel and Composite Structures
• /
• 제27권2호
• /
• pp.161-175
• /
• 2018

In this study, in-situ dynamic tests of the world's longest steel box tied-arch bridge over the Yangtze River, China, are reported. The double deck bridge supports highway and monorail systems at upper and lower levels, respectively. Strain, displacement, and acceleration responses were measured and used to investigate the vibration characteristics of the bridge when excited by running trains and/or trucks at a speed of 5-60 km/h, train braking, and truck bouncing. Impact factors were correlated with the running speed of trains and trucks. A three-dimensional finite element model of the coupled monorail-train-bridge vibration system accounting for track irregularities was established to understand the system behavior and validated by the experimental results. Truck bouncing was the dominant impact factor on bridge responses. The running speed of vehicles determined the riding comfort of traveling trains.

• 한국환경과학회지
• /
• 제19권10호
• /
• pp.1229-1235
• /
• 2010

Three meteor-statistical forecasting models - the transfer function model, the time-series autoregressive model and the neural networks model - were tested to develop a daily forecasting model for Jejudo, where the need and demand for wind power forecasting has increased. All the meteorological observation sites in Jejudo have been classified into 6 groups using a cluster analysis. Four pairs of observation sites among them, all having strong wind speed correlation within the same meteorological group, were chosen for a model test. In the development of the wind speed forecasting model for Jejudo, it was confirmed that not only the use a wind dataset at the objective site itself, but the introduction of another wind dataset at the nearest site having a strong wind speed correlation within the same group, would enhance the goodness to fit of the forecasting. A transfer function model and a neural network model were also confirmed to offer reliable predictions, with the similar goodness to fit level.