• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.5
• /
• pp.421-425
• /
• 2011

To know the speed performance of "ARAON" in Arctic ice field, the measurement of ice properties which is ice thickness & strength, snow depth and free board were performed on July 2010. The measuring method of nautical signals such as heading angle, power of engine, wind & current information etc. was described in this paper. The speed sea trials in ice were performed on the four different positions with different ice properties and engine powers because the uniform level ice is not detected in the Chukchi Sea. The test field was partially constrained ice floe with hummocks and it was superposed with small broken ice pieces each other. All of the measured ice properties were compared and evaluated according to the results of sea trial. The relations between speed, ice thickness, strength and power were summarized. Consequently according to the sea trial results, the speed of ARAON is 2.78knots at the 2.49m ice thickness with 6.55MW engine power.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.22-31
• /
• 2013

Flight tests on flight control performance of helicopter, conversion and airplane mode for the Smart UAV were completed. Automatic take-off and landing, automatic return home as well as automatic approach to hover were performed in helicopter mode. Climb/descent, left/right turn using speed and altitude hold mode were performed in each $10^{\circ}$ tilt angle in conversion mode. The rotor speed in airplane mode was reduced to 82% from 98% RPM in order to increase rotor efficiency with reducing Mach number at tip of rotors. It reached to the designed maximum speed, $V_{TAS}$=440 km/h at 3 km altitude. This paper presents the flight test result on full envelopment of Smart UAV. Detailed test plan and test data on control performance were also presented to prove that all data meets the flying qualities requirement.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.191-197
• /
• 2016

RCAR low speed impact test estimates repair cost of the impacted vehicle. In this study, for a mid-size vehicle front body model, structural performance for RCAR low speed impact were analyzed with changing the bumper stay shape and size. First, for improving the impact load transfer mechanism to side member the stay rear section shape at connecting area with side member was modified and the stay outer was redesigned to be normal to the barrier. Next, the investigation on stay thickness effect was carried out and the performances of several models with different forming shape were compared. The final design showed 13mm decrease in the maximum barrier intrusion distance and greatly reduced side member deformation. Additional analyses explained the validity of the final design.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.450-453
• /
• 2005

We test the running performance of KHST(Korean High Speed Train) that is developed in Korea. The interior noise of high speed train is dependent on the train speed generally and is one of the most important problem recently. In this paper, we present the test results of interior noise for KTX and KHST and examine into the cause of interior noise for KTX. From the analysis results, we know that the interior noise of KHST is lower about $2{\sim}5dB(A)$ than KTX and also the noise levels of KTX at 80Hz and 250Hz in tunnel increase very highly.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.22 no.2
• /
• pp.101-110
• /
• 2004

The local surface strength variation of coated papers were measured at various speeds on a number of coated paper samples to study the effects of speed and ink tack on coating pick. Coating pick phenomenon is observed in an ink transfer variation curve as a decrease in the slope of the curve. On the other hand, it causes an actual decrease in net ink transfer to paper with an increase in speed. The effect of speed on coating pick depends on ink tack, ink film thickness and surface properties of coating layer formation of paper. A novel device to measure the surface strength can rate the coating paper in a different order. Comparison are made between dry test of coating paper pick and wet coating pick test of printing in IGT printability tester. Coating formulation is the main key to prevent from coating pick. The binder level increases, the coating pick and the slop decrease. The piling on blanket in printing is a problem when the coating pick is occur on a local area rather than average surface strength of coated papers.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.141-143
• /
• 2004

Distributed generation(DG) using microturbine will be adopted widely because of its various usages and merits such as high heat efficiency, environmental-friendliness. Commercialized DG using microtubine that rotates up to $60,000\~100,000[rpm]$ converters mechanical power to electricity by permanent magnet synchronous machine. This paper presents comparative test and simulation results of PMSM as generator. Test was done by diode rectifier and inverter. Parameters used in the simulation are driven from FEM analysis. Under various speed and load conditions, V-I characteristics matches well and it suggests the possibility of high speed PMSM as generator. DG operating at stand alone and grid connection mode will be developed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.349-353
• /
• 2001

An air foil bearing is developed for the high speed generator. The bearing is type of multi-leaf and is stable on 60,000RPM. The vibration level is 12um(p-p) and the highest temperature level is below 100$^{\circ}C$. The dynamic parameter of air foil bearing is acquired by experimental method using exciter. The air foil bearing is also good condition at test of real generator and load condition. The condition of foil is very good after 3,000cycle start-stop test. Therefore the air foil bearing is ideal for high speed, light weight and modem turbo-machinery.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.517-524
• /
• 2005

An aerodynamic design for centrifugal compressor which was applied to medium speed diesel engine has done. First of all, exact compressor specifications must be defined by accurate engine system matching. This matching program has been developed. Using the mean1ine prediction method, geometric design and performance curve for compressor was done and verified by comparing three dimensional viscous CFD results. The deviation at the design point was about 2.3%. Combustor has been designed and manufactured for the performance test of medium speed diesel engine turbocharger. Fuel nozzle of combustor was designed and performed by PIV and PDPA test equipment. Through these results, spray characteristics were studied and flow coefficient equation was deduced.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.623-625
• /
• 2013

Tire hydroplaning is one of the most important tire performances, especially for safety on wet road surface. And nowadays various methods such as FEM and FVM analysis are being applied to design and improve tire hydroplaning performance, along with on-vehicle test of tire hydroplaning. Conventional evaluation of tire hydroplaning has been done by comparing peak lateral acceleration and vehicle speed in time domain. But in this paper, frequency domain analysis of lateral acceleration when hydroplaning at high speed has been carried out to get the quantitative comparison between test tires. And it is concluded that the frequency spectrum analysis of lateral acceleration gives much better discrimination, as compared to the conventional time domain analysis of lateral acceleration and vehicle speed.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.24 no.4
• /
• pp.71-83
• /
• 1987

There is at present a growing interest in the use of SWATH(Small Waterplane Area Twin Hull )ship for a variety of purposes due to their good seakeeping characteristics, small speed reduction in wave, and large deck area. Highly sophisticated design technology is requested to develop the SWATH ship. This paper describes the design technology for high speed coastal passenger SWATH ship which includes feasibility study, general arrangement and hull form design, resistance and propulsion test, motion test in regular waves, control fin design, and structural design.