• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.6
• /
• pp.512-519
• /
• 2004

This paper described the free vibration characteristics of Optimized H Type (OHT) spacer grids (SG) supporting the PWR fuel rod. The vibration test and the finite element (FE) analysis are performed under the free boundary condition and the clamped at two points (or three points) in the bottom which is the same one as the experimental condition for the dummy rod continuously supported by spacer grids. A modal test is conducted by the impulse excitation method using an impulse hammer and an accelerometer, and the TDAS module of the I-DEAS software is used to acquire and analyze the sensor signals. The softwares related to the FE analysis are the I-DEAS for the geometrical shape modeling and meshing, and the ABAQUS for solving. The fundamental frequency of the OHT SG by experiment under a clamped condition at two points is 175.18 Hz, and shows a bending mode. We think there is no resonance between the fuel rod and the SG because the SG's frequency is higher than that of the fuel rod existing in the range from 30 to 120 Hz. The fundamental frequency of the SG under the free boundary condition is 349.2 Hz showing a bending mode, and the results between the test and the analysis have a good agreement with maximum 7 ％ in error It is also found that the FE analysis model of the OHT SGs to analyze an impact, a buckling and vibration et al. has been generated with reliability.

• Molecules and Cells
• /
• v.23 no.2
• /
• pp.228-238
• /
• 2007

Since molecular structure of hnRNP is not available in foreseeable future, it is best to construct a working model for hnRNP structure. A geometric problem, assembly of $700{\pm}20$ nucleotides with 48 proteins, is visualized by a frame work in which all the proteins participate in primary binding, followed by secondary, tertiary and quaternary binding with neighboring proteins without additional import. Thus, 40S hnRNP contains crown-like secondary structure (48 stemloops) and appearance of 6 petal (octamers) rose-like architectures. The proteins are wrapped by RNA. Co-transcriptional folding for RNP fibril of FMR1 gene can produce 2,571 stem-loops with frequency of 1 stem-loop/15.3 nucleotides and 53 40S hnRNP beaded structure. By spliceosome driven reactions, there occurs removal of 16 separate lariated RNPs, joining 17 separate beaded exonic structures and anchoring EJC on each exon junction. Skipping exon 12 has 5'GU, 3'AG and very compact folding pattern with frequency of 1 stem-loop per 12 nucleotides in short exon length (63 nucleotides). 5' end of exon 12 contains SS (Splicing Silencer) element of UAGGU. In exons 10, 15 and 17 where both regular and alternative splice sites exist, SS (hnRNP A1 binding site) is observed at the regular splicing site. End products are mature FMR-1 mRNP, 4 species of Pri-microRNAs derived from introns 7,9,15 and 3'UTR of exon17, respectively. There may also be some other regulatory RNAs containing ALU/Line elements as well.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.41 no.1
• /
• pp.59-69
• /
• 2018

The up-to-date business environment for Korean manufacturers is very complex and rapidly changing. Especially, the companies have faced with various changes derived from small quantity batch production, diversification of customer demands, and short life cycles of products. Consequently, the Korean manufacturing companies are in need of more efficient production planning and scheduling techniques. In this paper, the research trend of scheduling techniques is investigated to provide relevant information to researchers in this field. Furthermore, some implications for future researches are presented regarding literatures published in Korea over the last 10 years. This paper presents an entire investigation into Korean research works on scheduling (2,569 papers) that are published from 2007 to 2016. Especially, detailed analysis was carried out in the following three industry : 1) semiconductor, 2) shipbuilding and 3) automobile. In this paper, approaches to scheduling presented in the literature are categorized into the following three categories : 1) application, 2) algorithm, and 3) simulation modeling. First, in the semiconductor industry, scheduling techniques related to semiconductor cleaning processes, photolithography processes, chemical processes, transport and transport equipment have been found to be dominant. Second, the shipbuilding industry is focused on assembly processes, transporter, crane and various existing production management system. On the other hand, the scheduling research of the automobile industry is mainly focused on the vehicle movement routing and procurement supply-chain planning algorithm in terms of logistics. The conclusion of this study are expected to provide many implications for various types of academic and practical follow-up studies related to scheduling in consideration of main characteristics of semiconductor, shipbuilding and automobile industries.

• Proceedings of the Korea Society for Industrial Systems Conference
• /
• 2006.05a
• /
• pp.211-217
• /
• 2006

The learning control develops controllers that learn to improve their performance at executing a given task, based on experience performing this specific task. In a previous work, the authors presented an iterative precision of linear decentralized learning control based on p-integrated learning method for the vertical dynamic multiple systems. This paper develops an indirect decentralized learning control based on adaptive control method. The original motivation of the teaming control field was teaming in robots doing repetitive tasks such as on an assembly line. This paper starts with decentralized discrete time systems, and progresses to the robot application, modeling the robot as a time varying linear system in the neighborhood of the nominal trajectory, and using the usual robot controllers that are decentralized, treating each link as if it is independent of any coupling with other links. Error wave propagation method will show up in the numerical simulation for five-bar linkage as a vertical dynamic robot. The methods of learning system are shown up for the iterative precision of each link at each time step in repetition domain. Those can be helped to apply to the vertical multiple dynamic systems for precision quality assurance in the industrial robots and medical equipments.

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.338-347
• /
• 2017

This paper describes the design and fabrication of a high power amplifier which is a component of TDL(Tactical Data Link) aircraft terminal. We applied high-speed frequency hopping technology, cognitive radio technology, and receive filter bank technology to efficiently use limited frequency resources with radar and other communication equipment using the same frequency band. The high-power amplifier is physically composed of a transmitter, a receiver, a mechanical part, and a cable assembly, and is designed to meet temperature characteristics and electrical characteristics such as maximum transmission distance and reception sensitivity. Modeling and simulator were used to satisfy the requirement of high power amplifier. The transmit power and the noise figure were measured at 50.02dBm and 2.682dB, respectively. It was confirmed that all the required specifications were satisfied in the electrical characteristics test and the environmental characteristic test.

• Journal of Aerospace System Engineering
• /
• v.11 no.6
• /
• pp.84-91
• /
• 2017

The dynamic characteristics of a ducted fan in hovering condition were investigated. The section properties of the fan blade were calculated, and a simulation model was developed according to the rotor system components. Dynamic analyses were conducted relative to the rotational speed and the collective pitch. The proposed ducted fan system showed less aero-elastic instability within the designated operating ranges. To verify the analytical approach, a rotating test stand of the ducted fan was set up. A functional test of the assembly was carried out to determine the kinematics and interference between components. The non-rotating and rotating normal frequencies were measured by excitation of the collective pitch using hydraulic actuators. The results indicated a correlation between the test equipment and the simulation model.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.2
• /
• pp.74-85
• /
• 2016

Seismic design of modular structures is usually carried out under the assumption that their load-carrying mechanism is similar to that of traditional steel moment-resisting frames(SMRFs). However, the load carry mechanism of modular structures would be different with that of traditional SMRFs because of their overlapped structural elements and complicated details of connections for the assembly of the unit-modules. In this study, nonlinear static analyses of 3 and 5-story prototype modular structures have been carried out with four different analytical models, which are established in consideration for the effects of overlapped elements and the hysteretic behavior of connections. Prototype structures present different lateral stiffness and strength depending on the modeling of overlapped elements and the rotational behavior of connections. For modular structures designed under assumption that overlapped structural elements are fully composite each other and connections between unit-modules are fixed, their lateral strength and stiffness can be over-estimated. Furthermore, it is known from the analysis results that modular structures with more than 3-stories would possess relatively low overstrength compared to traditional SMRFs.

• Nuclear Engineering and Technology
• /
• v.41 no.6
• /
• pp.821-830
• /
• 2009

In this paper, modal testing and finite element modeling results to identify the modal parameters of a nuclear fuel rod as well as its cladding tube are discussed. A vertically standing full-size cladding tube and a fuel rod with lead pellets were used in the modal testing. As excessive flow-induced vibration causes a failure in fuel rods, such as fretting wear, the vibration level of fuel rods should be low enough to prevent failure of these components. Because vibration amplitude can be estimated based on the modal parameters, the dynamic characteristics must be determined during the design process. Therefore, finite element models are developed based on the test results. The effect of a lumped mass attached to a cladding tube model was identified during the finite element model optimization process. Unlike a cladding tube model, the density of a fuel rod with pellets cannot be determined in a straightforward manner because pellets do not move in the same phase with the cladding tube motion. The density of a fuel rod with lead pellets was determined by comparing natural frequency ratio between the cladding tube and the rod. Thus, an improved fuel rod finite element model was developed based on the updated cladding tube model and an estimated fuel rod density considering the lead pellets. It is shown that the entire pellet mass does not contribute to the fuel rod dynamics; rather, they are only partially responsible for the fuel rod dynamic behavior.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.12
• /
• pp.1035-1042
• /
• 2014

Reducing the friction of engine parts is an important issue in engine design. The loss of energy in the piston assembly due to mechanical friction ranges from 40 to 55%, and there is an increase in the total energy of about 5% if the friction of the piston can be removed. In order to reduce the friction loss at the level of each engine part, it is necessary to perform a comparative analysis with other engines to determine the important factors affecting the energy loss. Several studies have been performed to analyze the lubrication based on hydrodynamic modeling, since a piston lubrication system has dimensions in the nanoscale to microscale domain. Therefore, it is necessary to determine the correlations between the molecular and continuum systems. In this study, we investigated the friction changes due to the various interactions between molecules in the wall/fluid interface, where a microscopic movement of the oil film occurs along the cylinder liner of the engine.

• Journal of Korea Society of Industrial Information Systems
• /
• v.11 no.2
• /
• pp.40-47
• /
• 2006

The learning control develops controllers that learn to improve their performance at executing a given task, based on experience performing this specific task. In a previous work the authors presented an iterative precision of linear decentralized learning control based on p-integrated teaming method for the vertical dynamic multiple systems. This paper develops an indirect decentralized learning control based on adaptive control method. The original motivation of the loaming control field was learning in robots doing repetitive tasks such as on a]1 assembly line. This paper starts with decentralized discrete time systems, and progresses to the robot application, modeling the robot as a time varying linear system in the neighborhood of the nominal trajectory, and using the usual robot controllers that are decentralized, treating each link as if it is independent of any coupling with other links. Error wave propagation method will show up in the numerical simulation for five-bar linkage as a vertical dynamic robot. The methods of learning system are shown up for the iterative precision of each link at each time step in repetition domain. Those can be helped to apply to the vertical multiple dynamic systems for precision quality assurance in the industrial robots and medical equipments.