• 센서학회지
• /
• 제15권3호
• /
• pp.192-198
• /
• 2006

In this study, the light addressable potentiometric sensors (LAPS) with $Si_{3}N_{4}/SiO_{2}/Si$, and $Ta_{2}O_{5}/SiO_{2}/Si$ structures were fabricated. The penicillinsae was immobilized on the devices to hydrolyze the penicillin using self-assembled monolayer (SAM) method. Then response characteristics according to the penicillin concentrations were measured and compared. The measuring system was simplified by using LabVIEW. The pH response characteristics of fabricated devices are 56 mV/pH ($Si_{3}N_{4}$ sensing membrane) and 61 mV/pH ($Ta_{2}O_{5}$ sensing membrane). The sensitivity of sensor by enzyme reaction result of the enzyme reaction were 60 mV/decade and 74 mV/decade for $Si_{3}N_{4}/SiO_{2}/Si$ and $Ta_{2}O_{5}/SiO_{2}/Si$ structure, respectively, in the range of $0.1\;mM{\sim}10\;mM $of the penicillin concentration.

• 한국정밀공학회지
• /
• 제26권5호
• /
• pp.142-149
• /
• 2009

This paper proposes and demonstrates novel flexible contact force sensing devices for 3-dimensional force measurement. To realize the sensor, polyimide and polydimethylsiloxane are used as a substrate, which makes it flexible. Thin-film metal strain gauges, which are incorporated into the polymer, are used for measuring the three-dimensional contact forces. The force sensor characteristics are evaluated against normal and shear load. The fabricated force sensor can measure normal loads up to 4N. The sensor output signals are saturated against load over 4N. Shear loads can be detected by different voltage drops in strain gauges. The device has no fragile structures; therefore, it can be used as a ground reaction force sensor for balance control in humanoid robots. Four force sensors are assembled and placed in the four corners of the robot's sole. By increasing bump dimensions, the force sensor can measure load up to 20N. When loads are exerted on the sole, the ground reaction force can be measured by these four sensors. The measured forces can be used in the balance control of biped locomotion system.

• 폴리머
• /
• 제29권3호
• /
• pp.308-313
• /
• 2005

광감응성 azobenzene 그룹이 분자의 주위 환경에 따라 광이성화 반응이 변화하는 것을 in-situ UV/Vis 분광 실험법과 광학 이방성 측정법을 이용하여 조사하였다. 4-Hyhoxyazobenzene을 포함하는 필름에 광조사함과 동시에 trans-isomer와 cis-isomer 특성 피크의 세기 변화를 측정하여 azobenzene 그룹의 가역적이며 반복적인 광이성화 반응을 알수 있었다. Azobenzene 자기조립체 박막이 입혀진 기판을 액정 셀의 배향막으로 사용하여 액정의 배향을 유도하였을 때, trans-azobenzene 그룹들이 조밀한 packing을 하며 기판에 수직으로 배열한 자기조립체 구조 때문에 액정 분자들도 수직 homeotropic 배향을 하였다. 이와 같은 자기조립체 박막의 액정 셀에 UV 빛을 노광하면 azobenzene그룹이 광이 성화 반응을 일으켜 cis-isomer로 변하게 되며, 이로 인해 액정의 배향이 수직에서 수평 planar 배향으로 변함을 알 수있었다.

• 미술이론과 현장
• /
• 제9호
• /
• pp.151-170
• /
• 2010

As an art group, De Stijl (1917-1931) led a total art movement encompassing painting, sculpture, design, and architecture. Among these, architecture, as a model of the total art pursued by the group, was encapsulated by the term 'plastic architecture.' The term reflects architecture's shared features with plastic art, especially its pictorial characteristics. Firstly, De Stijl architecture shares geometric form with painting. Assembled in simple, clear and rational structures, the geometric forms signified universal forms, and extended the pictorial experimentation that Mondrian exercised through Neo-Plasticism to architecture. Constructed with colour fields made of concrete wall, De Stijl architecture is geometric abstract painting embodied in space. Together with such pictorial characteristics, large plate glass windows, narrow window frames, and cantilever structure minimize the building's visual weight. De Stijl architecture, which appears suspended in the air, is an architectural version of the abstract paintings of the era that revealed unknown spaces beyond perspective. De Stijl architecture is also an 'open' architecture, where the units placed as if radiating from the center form relations with each other flexibly and organically. The observer in such a space is encouraged to experience space within time, as his/her physical and visual mobility and extension are maximized. De Stijl architecture is an example of how the time-space continuum, represented within picture frame through Cubism, Futurism, and abstract art, can be realized in space. By transforming the ideal space of painting into real space in this way, 'plastic architecture' turned out to be an architectural manifestation of the utopianism of the era, aimed at building a society in 'perfect harmony.' However, such rationalism and universalism are not free from the violence of totalization that deletes various differences. This is evident in the history that followed as the geometric form of architecture and urban planning proliferated across the globe, engulfing the diverse natural landscapes and local cultures.

• 한국전기전자재료학회논문지
• /
• 제23권6호
• /
• pp.502-507
• /
• 2010

In order to design nano structured materials with enhanced thermoelectric properties, the alloys in the pseudo-binary $Bi_2Te_3$-PbTe system are investigated for their micro structure properties. For this synthesis, the liquid alloys are cooled by the water quenching method. Micro structure images are obtained by using an electron probe micro analyzer(EPMA). Dendritic and lamellar structures are clearly observed with the variation in the composition ratio between $Bi_2Te_3$ and PbTe. The increase in the $Bi_2Te_3$ composition ratio causes to change of the structure from dendritic to lamellar. The Seebeck coefficient of sample 5, in which the mixture rate of $Bi_2Te_3$ is 83%, is measured as the highest value. In contrast, the others decrease with the increase of the $Bi_2Te_3$ composition ratio. Meanwhile, p-type characteristics are observed in sample 6, at 91%-$Bi_2Te_3$ mixture rate. The power factors of the all samples are calculated with the Seebeck coefficient and resistivity.

• 한국강구조학회 논문집
• /
• 제30권2호
• /
• pp.77-85
• /
• 2018

각형강관 기둥을 이용한 모멘트 접합부는 주로 관통형 다이어프램 형식으로 사용되고 있으나, 제작 및 시공과정이 복잡하여 적용하는데 어려움이 있다. 본 연구에서 제안하는 강구조물 시스템은 단위 유닛 모듈(각형강관 기둥, H형강 보, 원웨이 볼트)을 현장으로 반입하여 볼트조립만으로 완성되는 것이다. 따라서 이 연구에서는 내부보강판의 길이, 내부보강판의 형상을 변수로 설정하여 제안된 기둥-보 접합부의 내력 및 강성, 연성능력, 에너지 소산능력을 비교 분석하여 제시된 강구조물 시스템을 평가하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.437-441
• /
• 2001

This paper describes the construction of a circular polariscope. Generally, a circular polariscope contains four optical elements and a light source. The first element following the light source is called the polarizer. It converts the ordinary light into plane-polarized light. The second element is a quarter wave plate which converts the plane-polarized light into circularly polarized light. Following the quarter wave plate, a specimen made of transparent photoelastic material is located in a loading device. The second quarter wave plate is set and the last element is the analyzer. These polarizing elements, two quarter wave plates and two polarizing filters, were purchased from the USA. Frames and other structures for holding polarizing filters were machined and assembled to be rotated. Light box, which include four incandescent lamps and two sodium-vapor lamps, was made. In order to proof the function of the newly built polariscope, Tardy compensation test was applied to a rectangular shaped specimen made of poly-carbonate material (PSM1). The error of the fringe constant, which was measured by the newly built polariscope, was within 4.4 percent compared to the standard value of this material. It is possible to make a good quality of polariscope if accurate polarizing filters will be used.

• 대한기계학회논문집B
• /
• 제40권3호
• /
• pp.149-155
• /
• 2016

휘발성 유기화합물과 같은 환경유해물질의 조기 검지는 인체 및 환경보호를 위한 중요성을 가진다. 그러나 기존의 모니터링 기술은 많은 시간과 값비싼 장비를 필요로 하고 있다. 본 논문에서는, 무전원으로 작동가능하며, 휴대가 용이하고 빠른 응답속도를 가지는 광결정 기반의 VOC 검출용 박막센서를 제안하였다. 휘발성 유기 화합물은 Polydimethylsiloxane(PDMS)를 팽창시키는 능력을 가지고 있어, 제안된 센서에 휘발성 유기 화합물이 노출되면 PDMS 가 팽창함에 따라 광결정의 구조변화를 가져오므로 색이 변하게 된다. 이러한 원리에 기초하여 휘발성 유기 화합물에 노출되었을 때 가시광선 영역의 정량적 색변화를 통해 검출할 수 있는 환경센서를 구현하였다. 제안된 센서는 수 초 이내의 빠른 반응속도를 보이며, 기체 상태의 휘발성 유기 화합물에도 색 변화를 일으키는 것을 성공적으로 확인하였다.

• 대한디지털의료영상학회논문지
• /
• 제11권2호
• /
• pp.85-92
• /
• 2009

This study, "The study about performance evaluations of mobile cover for X-ray's diffusion and distribution in mobile radiation" is based on the rules of mobile defense apparatus for radiation producer in 2006. To use the mobile cover for X-ray for diagnosis has been compulsory in common wards except operation rooms, emergency rooms and intensive care units. we have confirmed the effect in arbitrary shielding material after Qualitiy Control was carried out for accuracy in an experiment of mobile photographing equipment. The performance evaluation was conducted with the fabrics of selenium, 0.2 mmPb, 0.1 mmPb and aluminiums. Considering the result, we choosed 0.1 mmPb and attached cover to mobile photographing equipment. We have finished making the cover after drew up the draft to attach cover to mobile photographing equipment through the modeling and the structural analysis. the process of the study is that we assembled the manufactured structures and carried out the practical experiment to take the photograph after attaching the fabric of 0.1 mmPb to mobile photographing equipment. It is need of additional thesises hereafter that we compare the result between the part to improve for safety besides convenience in photographic experiment about clinical radiation and the effect of covering the diffusion in condition attached the cover.

• Journal of Welding and Joining
• /
• 제28권3호
• /
• pp.65-72
• /
• 2010

Some structural members of large-scale marine vessels such as large-scale offshore structures and very large container ships are assembled by very thick plates of which thickness exceeds 60mm. Also, high-tensile steels have been selected to meet the required structural strength and fatigue strength. Generally, multi-pass welding method such as FCA(Flux-Core Arc) welding has been used to join the thick plates. Considering the welding residual stresses, fatigue strength of the welded joints of thick plates should be assured since the residual stress influences the fatigue strength. This paper presents a numerical procedure to investigate the residual stress of structure joined by multi-pass FCA welding so that it can be incorporated into the fatigue strength assessment considering the effect of welding residual stress. The residual stress distribution is also measured by X-Ray diffraction method. The residual stress obtained by the computational model also has been compared with that of experiment. The results of FEA are in very good agreement with the experimental measurements.