• 제목/요약/키워드: Aspect ratio(AR)

검색결과 94건 처리시간 0.028초

A-TIG 용접에서 용입 형상비에 미치는 아크길이와 실드가스의 영향 (The Eeffect of Arc Length and Shield Gas on Penetration Aspect Ratio in A-TIG Welding)

  • 박인기;함효식;조상명
    • Journal of Welding and Joining
    • /
    • 제26권6호
    • /
    • pp.42-47
    • /
    • 2008
  • TIG welding enables to produce high quality weldment. However it has some problems such as shallow penetration and large distortion due to low penetration aspect ratio after welding. In order to overcome those problems, there are many ongoing studies on A-TIG welding, which use active flux. In this study, the effect of arc length and shield gas on penetration aspect ratio with melt-run welding on STS 304 6t, on which active flux was spreaded, was investigated. Arc length was changed from 1mm to 3mm, and aspect ratio became higher as arc length was decreased in this range. 100% Ar gas, Ar-$H_2$ mixed gas, Ar-He mixed gas, and 100% He gas were used as shield gas in this study. When Ar-$H_2$ mixed gas, Ar-He mixed gas, and 100% He gas were applied, penetration and melting efficiency were both increased as compared with 100% Ar gas. Aspect ratio was the highest with Ar-2.5% $H_2$ mixed gas.

Convective heat and mass transfer affected by aspect ratios for physical vapor transport crystal growth in two dimensional rectangular enclosures

  • Kim, Geug Tae;Kwon, Moo Hyun
    • 한국결정성장학회지
    • /
    • 제28권2호
    • /
    • pp.63-68
    • /
    • 2018
  • Natural convection of a two dimensional laminar steady-state incompressible fluid flow in a rectangular enclosure has been investigated numerically for low aspect ratios with the physical vapor transport crystal growth. Results show that for aspect ratio (Ar = L/H) range of $0.1{\leq}Ar{\leq}1.5$, with the increase in Grashof number by one order of magnitude, the total mass flux is much augmented, and is exponentially decayed with the aspect ratio. Velocity and temperature profiles are presented at the mid-width of the rectangular enclosure. It is found that the effect of Grashof number on mass transfer is less significant when the enclosure is shallow (Ar = 0.1) and the influence of aspect ratio is stranger when the enclosure is tall and the Grashof number is high. Therefore, the convective phenomena are greatly affected by the variation of aspect ratios.

종횡비에 따른 타원제트의 유동특성에 관한 실험적 연구 (The Effect of Aspect Ratio on the Flow Characteristics of Elliptic Jets)

  • 권영철;이상준
    • 대한기계학회논문집
    • /
    • 제16권6호
    • /
    • pp.1156-1162
    • /
    • 1992
  • 본 연구에서는 종횡비가 다른 3가지의 날카로운 모서리를 가진 타원 슬롯노즐 (AR=1,2,4)을 풍동 수축부 끝에 장착하여 타원제트의 유동특성 및 축교차현상을 3-D LDV 시스템을 이용하여 조사하였다.

DEM study on effects of fabric and aspect ratio on small strain stiffness of granular soils

  • Gong, Jian;Li, Liang;Zhao, Lianheng;Zou, Jinfeng;Nie, Zhihong
    • Geomechanics and Engineering
    • /
    • 제24권1호
    • /
    • pp.57-65
    • /
    • 2021
  • The effects of initial soil fabric and aspect ratio (AR) on the small-strain stiffness (G0) of granular soils are studied by employing discrete element method (DEM) numerical analysis. Elongated clumps composed of subspheres were adopted, and the G0 values were obtained by DEM simulations of drained triaxial tests under different densities and initial confining pressure (p0). The DEM simulations indicate that the initial soil fabric has an insignificant effect on G0. The effect of the AR on G0 is related to the initial density. Namely, for dense specimens, G0 first increases with increasing AR, reaching a plateau value when the AR ≥ 1.5. However, for loose specimens, G0 gradually increases as the AR increases. Microscopic examination reveals that G0 uniquely depends on the coordination number of the particles (CN-particle) rather than the subspheres (CN-sphere) at the particulate level for the effects of initial soil fabric and AR. Finally, Poisson's ratio ν0 is also determined by CN-particle. In addition, based on data in literature and this study, ν0 can be fitted as ν0 = 5.920(G0/(p0)1/3)-0.99, which can be used to predict ν0 of granular soils based on the measured G0.

Preliminary Studies on Double-Diffusive Natural Convection During Physical Vapor Transport Crystal Growth of Hg2Br2 for the Spaceflight Experiments

  • Ha, Sung Ho;Kim, Geug Tae
    • Korean Chemical Engineering Research
    • /
    • 제57권2호
    • /
    • pp.289-300
    • /
    • 2019
  • We have conducted a preliminary numerical analysis to understand the effects of double-diffusive convection on the molar flux at the crystal region during the growth of mercurous bromide ($Hg_2Br_2$) crystals in 1 g and microgravity (${\mu}g$) conditions. It was found that the total molar fluxes decay first-order exponentially with the aspect ratio (AR, transport length-to-width), $1{\leq}AR{\leq}10$. With increasing the aspect ratio of the horizontal enclosure from AR = 1 up to Ar = 10, the convection flow field shifts to the advective-diffusion mode and the flow structures become stable. Therefore, altering the aspect ratio of the enclosure allows one to control the effect of the double diffusive natural convection. Moreover, microgravity environments less than $10^{-2}g$ make the effect of double-diffusive natural convection much reduced so that the convection mode could be switched over the advective-diffusion mode.

후향계단이 있는 사각덕트 내부의 유동특성 연구 (A study of backward-facing step flow in a rectangular duct)

  • 김성준;최병대
    • 산업기술연구
    • /
    • 제19권
    • /
    • pp.59-65
    • /
    • 1999
  • This study is to analyze turbulent flow over a backward-facing step in a rectangular duct. The side wall effects on the internal flow were determined by varying the aspect ratio(defined as the step span-to-height ratio) from 1 to 20. In the flow behind a backward-facing step, separation, recirculation and redeveloping is occurred frequently. These phenomena appear in a particular variation by varying the aspect ratio. The results show that the aspect ratio has an influence on the velocity and reattachment length. When the AR is increased, the reattachment length is increased. For 6 over aspect ration, the rate of increase is decreased. The length of recirculation in the upper corner is increased, as the increase of aspect ration. It's width is not changed in the variation of aspect ration. The transverse, streamwise and spanwise velocities were decreased along the flow down stream of the step.

  • PDF

날개의 종횡비가 날개 짓 운동의 공기역학적 특성에 미치는 영향 (The Effect of Aspect Ratio on Aerodynamic Characteristics of Flapping Motion)

  • 오현택;최항철;김광호;정진택
    • 유체기계공업학회:학술대회논문집
    • /
    • 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
    • /
    • pp.217-220
    • /
    • 2006
  • The lift and drag forces produced by a wing of a given cross-sectional profile are dependent on the wing planform and the angle of attack. Aspect ratio is the ratio of the wing span to the average chord. For conventional fixed wing aircrafts, high aspect ratio wings produce a higher lift to drag ratio than low ones for flight at subsonic speeds. Therefore, high aspect ratio wings are used on aircraft intended for long endurance. However, birds and insects flap their wings to fly in the air and they can change their wing motions. Their wing motions are made up of translation and rotation. Therefore, we tested flapping motions with parameters which affect rotational motion such as the angle of attack and the wing beat frequency. The half elliptic shaped wings were designed with the variation of aspect ratio from 4 to 11. The flapping device was operated in the water to reduce the wing beat frequency according to Reynolds similarity. In this study, the aerodynamic forces, the time-averaged force coefficients and the lift to drag ratio were measured at Reynolds number 15,000 to explore the aerodynamic characteristics with the variation of aspect ratio. The maximum lift coefficient was turned up at AR=8. The mean drag coefficients were almost same values at angle of attack from $10^{\circ}$ to $40^{\circ}$ regardless of aspect ratio, and the mean drag coefficients above angle of attack $50^{\circ}$ were decreased according to the increase of aspect ratio. For flapping motion the maximum mean lift to drag ratio appeared at AR=8.

  • PDF

Wind loading of a finite prism: aspect ratio, incidence and boundary layer thickness effects

  • Heng, Herman;Sumner, David
    • Wind and Structures
    • /
    • 제31권3호
    • /
    • pp.255-267
    • /
    • 2020
  • A systematic set of low-speed wind tunnel experiments was performed at Re = 6.5×104 and 1.1×105 to study the mean wind loading experienced by surface-mounted finite-height square prisms for different aspect ratios, incidence angles, and boundary layer thicknesses. The aspect ratio of the prism was varied from AR = 1 to 11 in small increments and the incidence angle was changed from α = 0° to 45° in increments of 1°. Two different boundary layer thicknesses were used: a thin boundary layer with δ/D = 0.8 and a thick boundary layer with δ/D = 2.0-2.2. The mean drag and lift coefficients were strong functions of AR, α, and δ/D, while the Strouhal number was mostly influenced by α. The critical incidence angle, at which the prism experiences minimum drag, maximum lift, and highest vortex shedding frequency, increased with AR, converged to a value of αc = 18° ± 2° once AR was sufficiently high, and was relatively insensitive to changes in δ/D. A local maximum value of mean drag coefficient was identified for higher-AR prisms at low α. The overall behaviour of the force coefficients and Strouhal number with AR suggests the possibility of three flow regimes.

사각 실린더를 지나는 층류 유동특성 (FLOW PAST A RECTANGULAR CYLINDER)

  • 박두현;양경수;안형수
    • 한국전산유체공학회지
    • /
    • 제20권3호
    • /
    • pp.47-53
    • /
    • 2015
  • This study performed numerical simulation to elucidate the characteristics of flow past a rectangular cylinder with various values of the aspect ratio(AR) of the cylinder. We calculated the flow field, force coefficients and Strouhal number of vortex shedding depending on the Reynolds number(Re) and the aspect ratio. The $AR{\approx}1$ is preferred for drag reduction, and 0.375$AR{\approx}0$ is recommended if suppression of the lift-coefficient fluctuation and the shedding frequency is desirable. Furthermore the criticality of the Hopf bifurcation is also reported for each AR.

태양열 계간 축열조 내부 열성층화에 대한 탱크 종횡비 영향 연구 (Effect of an aspect ratio on thermal stratification in a solar seasonal thermal storage tank)

  • 김성근;정성용
    • 한국가시화정보학회지
    • /
    • 제18권2호
    • /
    • pp.28-34
    • /
    • 2020
  • In this study, we numerically investigated the thermal stratification in solar seasonal thermal storage tanks. The vertical in/out flows were unsuitable for the thermal stratification in a large scale. The effect of an aspect ratio (AR) on the thermal stratification was investigated. When AR was less than 2, water adheres and flows along the upper wall due to buoyance and the surface effect. Thereafter, hot water flows down and a large scale vortex occurs in entire tank. For high AR, jet flows ejected from the inlet pipe impinges to the opposite wall and splits. The divided flows create two vortex flows in the upper and lower regions. These different flows strongly influence temperature and thermal stratification. The thermal stratification was evaluated in terms of the thermocline thickness and degree of stratification. Compared to ARs, the maximum degree of stratification was obtained with AR of 5 having the minimum thermocline thickness.