• Magazine of the Korean Society of Agricultural Engineers
• /
• v.37 no.3_4
• /
• pp.90-98
• /
• 1995

The recycled concrete, average compressive strength of which was 2l0kg/cm$^2$ or higher with slump range of 14~18cm, was prepared by replacing 25% and 50% by weight of coarse aggregate with recycled aggregate from waste concrete. Mix design method for crushed aggregates was used and all specimens were cured by normal moisture curing method. A plasticiser and a fly ash were added to the mix to improve performance of recycled concrete. Flexural strength, stress- strain relationship and fracture toughness were evaluated by comparing with those of normal concretes. Recycled concrete showed, in general, lower flexural strength and fracture toughness, and higher strain under the same stress level. Fly ash in the concrete had an effect of reducing the strength and fracture toughness on both normal and recycled concretes. Since fly ash is known to improve many properties of concrete, while reducing strength properties, decision for using fly ash should be made carefully depending on the intended usage of the recycled concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.161-162
• /
• 2017

As the use of cement increases with the development of modern society along with the increase of buildings, environmental pollution intensifies and researches on industrial byproducts are continuing. Research on blast furnace slag and fly ash as industrial byproducts is increasing, and research on industrial byproducts such as polysilicon sludge and paper ash used in this study is increasing. Blast furnace slag, which is one of the industrial byproducts, has been widely studied as a material used with cement. However, in this study, we fabricated lightweight matrix of polysilicon sludge and paper ash replaced based on blast furnace slag, and performed SEM analysis.

• Journal of the Korean Ceramic Society
• /
• v.52 no.2
• /
• pp.159-164
• /
• 2015

We manufacture artificial lightweight aggregates (ALWAs) using bottom-ash as the primary raw material. We coat the ALWA surfaces with low-melting point materials in order to enable them to bloat, which is essential to reduce the bulk density of the aggregate. Then, we sinter the prepared aggregates at 1000, 1100, and $1200^{\circ}C$ using either the direct or two-step firing schedules. Finally, we evaluate the properties of the fired samples through analyzing their bulk density, water absorption, and microstructure. The surface-modified samples result in a reduction of their bulk density by $0.3{\sim}0.4g/cm^3$ regardless of the firing method used. Based on these results, we conclude that this approach could provide a viable method for the mass-production of ALWAs from industrial waste such as bottom-ash.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.701-704
• /
• 2008

Actuality, amount of electric power is rising together with business expansion. But the most power plant is consisted a thermal power. People have been burning fuel like a coal, and it bring the cinder concrete. Fly-ash is use to the high-degree in construction material, but in case of bottom-ash had been disused the whole quantity. Intermittently, the academic world laid his studies for bottom-ash. Thus, this study contents are a characteristic of be not harden concrete incorporating fine aggregate, a strength of harden concrete, elastic modulus and a unit mass. And there do for the sake to examine utility value of bottom-ash and improve of light weight concrete.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.1
• /
• pp.55-60
• /
• 2019

Growing plant in potting media without soil is known as Soilless cultivation. This method is used mostly in greenhouse cultivation to increase horticultural commodities production. Peat moss is commonly utilized as potting media substrate because of its characteristic. However, peat moss price is high because of the quantity of peat moss in nature has been decreased. Recently, most of the research is conducted to find the alternative growing medium to cultivate horticulture plant in potting media. Perlite and rice husk ash were mentioned that had a potent as alternative growing media for seasonal plants to increase agriculture production due to the lack of production area. This research aims to determine the growth of in rice husk ash, perlite and peat moss as growing substrates. The method used was the soilless cultivation. The chinese cabbage was planted in the pot with perlite media, rice husk ash media, and peat moss media. The chinese cabbage was measured after 35 days after planting. The result showed that peatmoss was more potentials in chinese cabbage growth performance than rice husk ash and perlite. Peat moss had the significant result of every research parameters such as plant height, plant weight, number of leaves, plant diameter, root length, and root weight. The best alternative for cultivation chinese cabbage without substrate based on this research was peat moss then rice husk ash and perlite.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.6
• /
• pp.85-91
• /
• 2010

As enormous construction projects of land development are carried out around Korea, useful construction materials are needed to perform the construction projects. However, there are no more enough of fill and reclamation materials in our country. That is why the coal ash is expected to be utilized as an alternative material. Since the coal ash has the characteristics of a pozzolan and a selfhardening material, it is adjudged that coal ash has a great possibility to be used as a fill and reclamation material. In this study, grain size analysis, Atterberg limit test, and specific gravity test were performed to examine the physical characteristics of the coal ash about a self-hardening material before utilizing the coal ash in the construction. Compaction test, unconfined compression test, direct shear test, and flexible wall permeability test were conducted to investigate the engineering characteristics according to mixture ratios of fly ash and bottom ash. As a result of the tests, it was confirmed that the mixing ratio 1:1 of fly ash and bottom ash is the most effective to use as a fill and reclamation material. If the mixture of coal ash is used as a backfill material with light weight around structure, it is expected to play a significant role in reducing earth pressure on the back of the structure. As the age of the mixture of coal ash goes by, it intends to decrease the coefficient of permeability. As described above, the coal ash should be considered as an alternative material of fill and reclamation materials since the result of the tests indicates that the coal ash is suitable to a useful material on the construction design.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.73-82
• /
• 2011

Coal ash of industial by-products was not recycled about 30% in total emissions. Moreover, it caused environmental pollution as well as wasted unnecessary expenses and time. Currently, fly ash(FA) is recycled as construction material however ponded ash(PA) is mostly buried. Lightweight foamed Controlled Low-Strength Materials(CLSM) evaluated in this study reduces unit weight by mixing foam in the traditional Controlled Low-Strength Material and has lightweight and flowability to be available for backfill materials in construction. Flow test, unconfined compressive strength test, and foamed-slurry unit weight test were performed in this study and the applicability of lightweight foamed CLSM for construction materials was evaluated. The results indicate that the mixture ratio(PA:FA) ranging from 70:30 to 50:50, cement of 7%, foam of 2~3%, and water content of 26.5~29.5% were required to satisfy the following standards such as flow value(i.e., 20cm), unconfined compressive strength(i.e., 0.8~1.2MPa), and foamed-slurry unit weight(i.e., $12{\sim}15kN/m^3$).

• Structural Engineering and Mechanics
• /
• v.72 no.3
• /
• pp.339-354
• /
• 2019

Reusing building materials and concrete of old buildings can be a promising strategy for sustained development. In buildings, the performance of materials under elevated temperatures is of particular interest for determining fire resistance. In this study, the effect of pozzolan and aggregate type on properties of concrete exposed to fire was investigated. In doing so, nanosilica with cement-replacement levels of 0, 2, and 4% as well as silica fume and ultrafine fly ash with cement-replacement levels of 0, 7.5, and 15% were used to study effect of pozzolan type, and recycled refractory brick (RRB) fine aggregate replacing natural fine aggregate by 0 and 100% was utilized to explore effect of aggregate type. A total of 126 cubic concrete specimens were manufactured and then investigated in terms of compressive strength, ultrasonic pulse velocity, and weight loss at $23^{\circ}C$ and immediately after exposure to 400 and $800^{\circ}C$. Results show that replacing 100% of natural fine aggregate with recycled refectory brick fine aggregate in the concretes exposed to heat was desirable, in that it led to a mean compressive strength increase of above 25% at $800^{\circ}C$. In general, among the pozzolans used here, silica fume demonstrated the best performance in terms of retaining the compressive strength of heated concretes. The higher replacement level of silica fume and ultrafine fly ash pozzolans in the mixes containing RRB fine aggregate led to a greater weight loss rate, while the higher replacement level of nanosilica reduced the weight loss rate.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.365-374
• /
• 2010

The ash reduction effects and fuel property changes of spent mushroom substrates by acid solution extraction, and the production possibilities of wood pellet fuel using them were studied. The ash weight of spent Pleurotus eryngii substrates was reduced from 8.81%(w/w) to 3.33%(w/w), and calorific value was increased from 3,958.3 kcal/kg to 4219.2 kcal/kg when extracted with a mixture of Acetic acid 2%(w/w) and Anhydrous citric acid 1%(w/w) in condition of liquid ratio 1:8, extraction temperature $55^{\circ}C$ and extraction time 180 min. The ash weight of spent Flammulina velutipes substrates was reduced from 14.91%(w/w) to 4.07%(w/w), and calorific value was increased from 4,190.3 kcal/kg to 4,219.2 kcal/kg when extracted with a mixture of Acetic acid 3%(w/w) and Anhydrous citric acid 1%(w/w) in condition of liquid ratio 1:8, extraction temperature $65^{\circ}C$ and extraction time 180 min. The ash weight of spent Pleurotus osteratus substrates was reduced from 3.31%(w/w) to 0.59%(w/w), and the smallest reduction was in calorific value from 4,558.6 kcal/kg to 4,216.2 kcal/kg when extracted with a mixture of Acetic acid 1%(w/w) and Anhydrous citric acid 1%(w/w) in condition of liquid ratio 1:8, extraction temperature $65^{\circ}C$ and extraction time 180 min.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.6
• /
• pp.81-95
• /
• 2011

This study investigates relative density test of standard sand and bottom ash which were devided into No.40, No.60, No.100, No.200 and resonant column tests were conducted for samples with the relative density of 40%, 55%, and 70% on the basis of the test results. Resonant column tests were also conducted for each residual bottom ash which contains the passing sample of No.200 with the relative density of 55%. By compressing each residual sample with the compaction energy of A-compact mold test, the passing percentage of No.200 sieve increased up to 30%, which led to the adjustment of relative density to 10%, 20%, and 30%. Test results show that maximum shear modulus and damping ratio of bottom ash are smaller than those of standard sand because crushing strength and unit weight of the former are smaller than those of the latter.