• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2006년도 Proceedings of ISRS 2006 PORSEC Volume II
• /
• pp.804-807
• /
• 2006

The SRI(Super Resolution Imager) with 800mm aperture primary mirror is the ground development model of the high resolution satellite camera. The SRI focal plane electronics including detector array generates the data for high-resolution images by converting incoming light into digital stream of pixel data. Since the focal plane including a detector is the basic building block of the camera system, the main system performances is directly determined by its performance. This paper measures the SRI focal plane electronics’ performance such as the dark signal, the dark signal noise, the linearity, the PRNU(Photo Response Non-Uniformity), the SNR(Signal to Noise Ratio) and the sensor saturation capability. In addition, this paper verifies the various functionalities of the SRI focal plane electronics. The electrical test equipment with the specialized software and the optical test equipments such as the integrating sphere, the rotation stage and the target are implemented and used to verify these functionalities and performances.

• 전기학회논문지
• /
• 제67권6호
• /
• pp.782-788
• /
• 2018

This paper proposes a novel method for the omnidirectional camera-based image rendering synchronization system using head mounted display. There are two main processes in the proposed system. The first one is rendering 360-degree images which are remotely photographed to head mounted display. This method is based on transmission control protocol/internet protocol(TCP/IP), and the sequential images are rapidly captured and transmitted to the server using TCP/IP protocol with the byte array data format. Then, the server collects the byte array data, and make them into images. Finally, the observer can see them while wearing head mounted display. The second process is displaying the specific region by detecting the user's head rotation. After extracting the user's head Euler angles from head mounted display's inertial measurement units sensor, the proposed system display the region based on these angles. In the experimental results, rendering the original image at the same resolution in a given network environment causes loss of frame rate, and rendering at the same frame rate results in loss of resolution. Therefore, it is necessary to select optimal parameters considering environmental requirements.

• Journal of the Optical Society of Korea
• /
• 제16권4호
• /
• pp.381-385
• /
• 2012

In this paper, we present a novel integral imaging pickup method. We extract each pixel's actual depth data from a real object's surface using a depth camera, then generate elemental images based on the depth map. Since the proposed method generates elemental images without a lens array, it has simplified the pickup process and overcome some disadvantages caused by a conventional optical pickup process using a lens array. As a result, we can display a three-dimensional (3D) image in integral imaging. To show the usefulness of the proposed method, an experiment is presented. Though the pickup process has been simplified in the proposed method, the experimental results reveal that it can also display a full motion parallax image the same as the image reconstructed by the conventional method. In addition, if we improve calculation speed, it will be useful in a real-time integral imaging display system.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1989년도 한국자동제어학술회의논문집; Seoul, Korea; 27-28 Oct. 1989
• /
• pp.1059-1062
• /
• 1989

This paper describes a new method for two-dimensional(2D) positioning system by use of crosscorrelation of vague M-arrays. An M-array pattern is attached on an object to be positioned and it is observed by a TV camera in out-of-focus condition. The crosscorrelation between the observed image data and the reference M-array gives us the information about the 2D position of the object.

• 전자공학회논문지D
• /
• 제34D권11호
• /
• pp.20-24
• /
• 1997

We have successfully fabricated high power (~20W) laser diode array, which are useful for pumping Nd:YAG lasers. The laser diode aray has 20 100.mu.m-wide cahnnels of which space was adjusted to 350.mu.m to improve thermal characteristics. And channel width is 100.mu.m. For an uncoated LD array, the output power of 15.66W has been obtained at 41A under quasi-CW operation, which results in about 0.42W/A slope efficiency. After aR(5%) and HR (95%) coatings on both facets, the output power was improved up to 21.18W at 40A under the same operation as above and the slope efficiency was 0.795W/A. On the other hand, by using a near field measurement system consisting of objective lens, eyepiece, CCD camera and image processing board, the typical near field patten of 1*20 LD array was observed.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.169-170
• /
• 2006

The main purpose of this study is to develop a program for sound field visualization system which gets noise signals in microphones array for incoming noise signals and it uses to operate noise signals and to store data in multi-channel FFT and is consisted to visualize noise signals with a image which is got by camera in center of array by using beamforming algorithm of the array signal processing.

• Current Optics and Photonics
• /
• 제6권3호
• /
• pp.304-312
• /
• 2022

Digital images of cultural relics captured using line scan cameras present limitations due to uneven intensity and low contrast. To address this issue, this report proposes a colour linear array image enhancement method that can maintain a constant colour. First, the colour linear array image is converted from the red-green-blue (RGB) colour space into the hue-saturation-intensity colour space, and the three components of hue, saturation, and intensity are separated. Subsequently, the hue and saturation components are held constant while the intensity component is processed using the established intensity compensation model to eliminate the uneven intensity of the image. On this basis, the contrast of the intensity component is enhanced using an improved local contrast enhancement method. Finally, the processed image is converted into the RGB colour space. The experimental results indicate that the proposed method can significantly improve the visual effect of colour linear array images. Moreover, the objective quality evaluation parameters are improved compared to those determined using existing methods.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1979년도 하계 전자.전기연합학술발표회논문집
• /
• pp.162-163
• /
• 1979

A new detector array scheme for the positron camera for tile improved image resolution and a method for the resolution improvement of the undersampled projection data from ring positron camera are proposed. Computer simulation results are presented and problems ana limitations are discussed.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2009년도 창립 20주년기념 특별학술발표회
• /
• pp.323-324
• /
• 2009

In this paper, we use multi-point sources to illuminate the sample in digital holographic microscopy. The resolution of digital holographic microscopy is enhanced without shifting the CCD camera. The specimen is illuminated from many directions by using multi-point sources which are easily created by a lens-array. The high frequency information of specimen can be captured at a fixed position of CCD camera. All information is then synthesized to increase the resolution.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1565-1567
• /
• 2004

Various defects are found in FPD (Flat Panel Display) manufacturing process. So detecting these defects early and reprocessing them is an important factor that reduces the cost of production. In this paper, the bare glass inspection system for the FPD which is the early process inspection system in the FPD manufacturing process is designed and implemented using the high performance and accuracy CCD line scan camera. For the preprocessing of the high speed line image data, the Image Processing Part (IPP) is designed and implemented using high performance DSP (Digital signal Processor), FIFO (First in First out), FPGA (Field Programmable Gate Array) and the Data Management and System Control part are implemented using ARM (Advanced RISC Machine) processor to control many IPP and cameras and to provide remote users with processed data. For evaluating implemented system, experiment environment which has an area camera for reviewing and moving shelf is made.