• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.3
• /
• pp.43-51
• /
• 2020

In this paper, the design of 64 array antennas applied to RWP (Radar Wind Profiler) was described. The design point of the antenna is to ensure isolation between each element and to match the vertical / horizontal radiation pattern. To this end, a single element of the array antenna was proposed as a Bend dipole type, and through simulation, When sequentially sending 5 beams including vertical, the east/west/south/north direction was ±20°, and it was confirmed that no Grating Lobe occurred when steering the beam. The 64 array antenna proposed in this paper was designed with performance equal to or higher than that of overseas products, and was confirmed to be applicable to RWP.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.8
• /
• pp.400-407
• /
• 1999

This paper treated the design, manufacture and the performance characteristics under each mode of high speed motor/generator for an electro-mechanical battery(EMB). This machine is employed as an integral part of a flywheel energy storage system(FESS), i.e., a modular flywheel system to be used as a device for storing electrical or mechanical energy. In this machine, the magnetic field system is constructed by using special magnet array, dipole Halbach array with 16 permanent magnet segments and the armature is composed of a plastic bobbin and multi-phase windings with Litz wire. The magnet array produces a highly uniform dipole field without back iron. The motor/generator is 3-phase machine in which the dipole Halbach array surrounding the winding is rotating. Since there are no iron laminations, this field system offers some unique advantages for the simplicity of the design and the theoretical prediction of characteristics of a high speed electric machine. This paper describes the results obtained when EMB system was tested in the laboratory.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.8
• /
• pp.1747-1754
• /
• 1997

The helical array antenna is designed for domestic DBS(Directcast Satellite) reception. The antenna diameter is determined 30cm with 168 element s to cover from Moojoo (beam center) to Seoul. The helical antenna with 2-turns and 4.deg. pitch angle is chosen as array elements for good axial ratio and antenna height. In array antenna design, row distance is 0.787.lambda., array distance is 0.824.lambda. in the same row. The feed is constructed using the radial waveguide to decrease the height of antenna. The measured values of the designed antenna are not only satisfied with the design goals but also similar to theoritical values except the axial ratio.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.2
• /
• pp.92-100
• /
• 2002

The 16-port feed waveguide array with inductive walls analyzed by Galerkin's method of moments are proposed for the DBS reception system mounted on vehicle. First of all, in order to verify the validity of electromagnetic analysis and design for a $\pi$-junction feed waveguide, it is designed and fabricated at DBS band. The measurement results of a $\pi$-junction feed waveguide agree well with the theoretical ones. Based on this design method, an array design for WR-90 standard waveguide is conducted. Since the width of a $\pi$-junction feed WR-90 standard waveguide is larger than a guided wave length in an array design, the difference of amplitude and phase of 8-port array are calculated 2.3 dB and 62 degrees, respectively. The bandwidth with return loss of -20 dB below is about 220 MHz and it doesn't satisfy DBS band. To solve this problem, we propose a novel design that the width of a $\pi$-junction feed waveguide equals to a guided wave length. By the proposed novel design for 8-port feed waveguide array, the difference of amplitude and phase are decreased 1 dB and 13 degrees, respectively. The broad bandwidth of 700 MHz is also realized. The size of 16-port waveguide away compared with WR-90 array is reduced about 10 cm. The measured antenna gain for the fabricated 16-port feed waveguide array is observed 24 dBi above at DBS band.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.2
• /
• pp.61-70
• /
• 1984

This paper examines the array antenna theory, basic relations between the array size (aperture) and its beamwidth and resultant patterns. This paper also provides array antenna system design criteria, mainly maximizing the signal-to-noise ratio (SNR) and its corresponding optimum array structure and weight functions. Explicit new expressions for array performance are also illustrated in terms of the array output SNR. An example is provided for a 37-element planar array to explicitly illustrate the beam-forming and nulling operations of the array. Fundamentals of sidelobe canceller (SLC) systems have been discussed along with a derivation of new SLC equations for optimum weights.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.5
• /
• pp.10-22
• /
• 2015

Recently, 3rd Generation Partnership Project (3GPP) has developed sidehaul system to cope with the explosively increasing mobile data traffic. The sidehaul system is based on single carrier-frequency division multiple access (SC-FMDA) due to its low peak to average power ratio (PAPR). Also, antenna array is designed to support multiple input multiple output (MIMO) in a restricted space. In this paper, we design the antenna array about uniform linear array (ULA), uniform circular array (UCA) and uniform planar array (UPA), and analysis the performance in sidehaul system. In addition, we propose the novel hybrid receiver full suppression cancellation (FSC) to reduce the interference from neighbor cell in sidehaul system. The proposed receiver can suppress and cancel the interference by combining interference rejection combining (IRC) with successive interference cancellation (SIC).

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.6
• /
• pp.43-55
• /
• 2013

In this paper, we propose a cylindrical active phased array antenna of Beam Steering Characteristics in the horizontal plane(H-plane) and vertical plane(E-Plane) on the cylinder form array structure. We design the bent dipole antenna of the cylindrical array structure adapted excellent mutual-coupling characteristics, designed and manufactured the cylindrical array antennas and power combiner/divider unit for power dividing and combining on the antenna. The radiating elements array spacing of Cylindrical array antenna were determined to avoid grating lobes at half power beam steering. Beam steering of the antenna was implemented with 6-bit phase shifter in the transceiver and have been designed based on the characteristics the antenna beam steering at -24 degrees to 24 degrees horizontal, vertical 0 degrees to 36 degrees beam steering. A cylindrical active phased array antenna that produced for verification the performance of the antenna are measured radiation characteristics in accordance with beam steering at L-Band.

• Korean Journal of Optics and Photonics
• /
• v.5 no.2
• /
• pp.204-211
• /
• 1994

Micro array lens systems are designed for a faximile or copy machine. The array type is hexagonal. Diameter of a lens is 0.16 mm and the distance of the center of the nearest neighbor is 0.192 mm. The magnitude of the lens system is 1:1. Working distane is 10.55 mm and the spot size is less than 0.04 mm radius on axis and 0.20 mm off-axis in case of single layer system. Working distance is 7.90 mm and the spot size is less than 0.07 mm radius on axis and 0.09 mm radius off axis in case of double layer system. Performance of single layer micro array lens system and double layer micro array lens system are compared with the characteristics of the ray fans.y fans.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.76-78
• /
• 2009

A liquid crystal display that does not use color filters is proposed. A backlight unit that employs compartmentalized RGB LED arrays and a lenticular lens array is used instead of the color filters in order to direct RGB LED lights into the RGB subpixels. A design of color-filterless LED backlight and experimental results are presented.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.3
• /
• pp.260-267
• /
• 2009

It is very difficult to form a desired complex sound field at a designated region precisely as an application of acoustic arrays, which is one of important objects of array systems. To solve the problem, a filter design method was suggested, which employed the concept of an inverse method using the acoustical holography based on the boundary element method. In the acoustical holography used for the source identification, the measured field data are employed to reconstruct the vibro-acoustic parameters on the source surface. In the analogous problem of source array design, the desired field data at some specific points in the sound field was set as constraints and the volume velocity at the surface points of the source plane became the source signal to satisfy the desired sound field. In the filter design, the constraints for the desired sound field are set, first. The array source and given space are modelled by the boundary elements. Then, the desired source parameters are inversely calculated in a way similar to the holographic source identification method. As a test example, a target field comprised of a quiet region and a plane wave propagation region was simultaneously realized by using the array with 16 loudspeakers.